Forum: Model A (1928-31)
06-08-2022, 08:09 AM
|
Replies: 29
Views: 4,009
Re: Stuck Head
My head puller:
I started with a 8" x 12" × 1/2" piece of steel from the scrap yard at 35 cents/lb.
1. Drilled and tapped holes for 7/16-20 x 6" bolts that thread through the plate and sit on...
|
Forum: Model A (1928-31)
06-04-2022, 11:10 AM
|
Replies: 21
Views: 4,343
|
Forum: Model A (1928-31)
05-23-2022, 10:42 AM
|
Replies: 18
Views: 2,572
|
Forum: Model A (1928-31)
05-23-2022, 06:21 AM
|
Replies: 18
Views: 2,572
Re: Water Inlet Leak
I don't recall using a cork one. If it's too thick and you do not tighten the bolts evenly I guess you could snap off one of the ears.
This would be more likely for the water outlet where head nut...
|
Forum: Model A (1928-31)
05-22-2022, 08:33 AM
|
Replies: 18
Views: 2,572
Re: Water Inlet Leak
I use this on hose connections. It's the Permatex version of the old Hylomar Blue:
...
|
Forum: Model A (1928-31)
05-22-2022, 08:08 AM
|
Replies: 18
Views: 2,572
Re: Water Inlet Leak
They are blind holes.
Remove ALL old gasket material and CLEAN mounting surfaces with a solvent to remove all residue. I use permatex on both surfaces and a paper gasket. A bit of permatex on the...
|
Forum: Model A (1928-31)
04-08-2022, 05:19 PM
|
Replies: 5
Views: 1,141
|
Forum: Model A (1928-31)
04-08-2022, 06:41 AM
|
Replies: 5
Views: 1,141
Radiator Filler Neck Replacement
The filler neck on my '30 original radiator is damaged and needs to be replaced. Since the originals are crimped on and soldered, how is that done?
|
Forum: Model A (1928-31)
03-31-2022, 04:27 PM
|
Replies: 12
Views: 1,955
|
Forum: Model A (1928-31)
03-16-2022, 05:21 AM
|
Replies: 23
Views: 2,552
|
Forum: Model A (1928-31)
03-04-2022, 08:16 AM
|
Replies: 18
Views: 1,640
|
Forum: Model A (1928-31)
01-14-2022, 08:04 AM
|
Replies: 28
Views: 4,806
Re: Fried rear bearing
Schwalms is the place to go.
Strasburg PA is about 250 miles from Yorktown VA. Don't drive I-95 during rush hour or bad weather. Even on beautiful sunny days it's a crap shoot.
|
Forum: Model A (1928-31)
01-13-2022, 10:11 AM
|
Replies: 41
Views: 6,282
Re: 1930 Tudor accident
I too have Hagerty insurance in Virginia. After reading this thread, I called them and added "Cherished Salvage" coverage to my policy. The additional premium was less than $20/yr. Basically, if...
|
Forum: Model A (1928-31)
01-09-2022, 08:01 AM
|
Replies: 32
Views: 5,584
|
Forum: Model A (1928-31)
01-08-2022, 06:14 AM
|
Replies: 25
Views: 5,436
Re: Bad manifold gaskets
Would it be better to use solid rings made from mild steel or cutting 304 stainless steel rings with a hacksaw to allow some thermal expansion?
|
Forum: Model A (1928-31)
01-06-2022, 11:57 PM
|
Replies: 25
Views: 5,436
Re: Bad manifold gaskets
What about rings cut from 316SS tube (1.500" OD X 16GA (0.065"))? With a significantly higher coefficient than cast iron can they still be solid or is a gap needed for thermal expansion?
|
Forum: Model A (1928-31)
12-23-2021, 10:16 AM
|
Replies: 25
Views: 5,436
|
Forum: Model A (1928-31)
12-23-2021, 07:13 AM
|
Replies: 25
Views: 5,436
Re: Bad manifold gaskets
I've read posts of homemade gland rings made from seamless steel pipe. Do those need to be cut to provide end gap for thermal expansion?
|
Forum: Model A (1928-31)
11-30-2021, 09:04 AM
|
Replies: 11
Views: 1,408
Re: Ignition cable through firewall
I have a look-a-like pop out switch and the thin cable to the distributor.. I've tried a couple of repro armored cables and they are way too stiff. I'd like to find an original cable with a good...
|
Forum: Model A (1928-31)
11-24-2021, 06:39 AM
|
Replies: 13
Views: 2,196
Re: Horn rod
Every repro retainer clip I've used needed to be dressed with a file to fit in the recess.
|
Forum: Model A (1928-31)
11-20-2021, 03:39 PM
|
Replies: 16
Views: 1,977
Re: Oil Pan Gaskets
Has anyone used a BESTgasket brand oil pan gasket?
Are the sold by any of the vendors?.
|
Forum: Model A (1928-31)
11-14-2021, 04:21 PM
|
Replies: 7
Views: 1,786
|
Forum: Model A (1928-31)
11-13-2021, 11:44 AM
|
Replies: 4
Views: 1,187
Re: Ignition Cable
How long have you had the shorter cable? I tried one probably 10 years ago and it was almost too stiff to bend at all. I've heard they are better now. The motor is out right now so I can't check...
|
Forum: Model A (1928-31)
11-12-2021, 10:21 PM
|
Replies: 7
Views: 1,786
Oil Drain Tube Thread Size
The hole in the rear bearing cap is 1/8-27 NPT. The tubes sold by the vendors are 3/8-32 UNF..
Should they be the same?
|
Forum: Model A (1928-31)
11-12-2021, 04:30 PM
|
Replies: 4
Views: 1,187
Ignition Cable
I currently have the thin stainless steel covered wire and a Nurex look-a-like pop out switch. For a more authentic appearance I purchased one of these short cables.
...
|