Forum: Early V8 (1932-53)
07-03-2021, 01:44 PM
|
|
Replies: 5
Views: 999
Brittle floor mat
My rubber floor mat 10 years old has become brittle. Is Dennis Carpenter the only place where you can purchase 1933 taupe rubber floor mat?
|
|
Forum: Early V8 (1932-53)
07-02-2021, 11:57 AM
|
|
Replies: 7
Views: 3,028
Re: Southside Obsolete?
I spoke with Fred this morning about ordering a part.
Thanks V8Coopman..For the new information.
I was using an old There was a disconnected number listed on the internet.
|
|
Forum: Early V8 (1932-53)
07-01-2021, 06:58 PM
|
|
Replies: 7
Views: 3,028
|
|
Forum: Early V8 (1932-53)
07-01-2021, 06:11 PM
|
|
Replies: 7
Views: 3,028
|
|
Forum: Model A (1928-31)
06-29-2021, 08:42 AM
|
|
Replies: 17
Views: 5,671
Re: Car jumps out of gear
The two lock plungers (A-7233) can also be worn on the ends so as to not
snap smartly into the rail slots.
Is it easy to replace the lock plungers on a 1933 model B transmission?
or is this...
|
|
Forum: Early V8 (1932-53)
07-29-2020, 07:23 AM
|
|
Replies: 3
Views: 1,623
installing windshield rubber gasket.
Is the groove in the windshield frame supposed to be tight enough to retain the rubber gasket without the use of adhesive? this is especially noticeable along the lower portion of the frame?
|
|
Forum: Early V8 (1932-53)
07-23-2020, 03:50 PM
|
|
Replies: 3
Views: 1,236
|
|
Forum: Early V8 (1932-53)
07-23-2020, 05:39 AM
|
|
Replies: 3
Views: 1,236
original Vinyl top look
I have been using Gerots Garage vinyl and rubber protectant for my top and running boards. The running boards look great, but the top is not shiney.
Should the top be shiney looking?
|
|
Forum: Early V8 (1932-53)
07-14-2020, 11:32 AM
|
|
Replies: 19
Views: 4,481
Re: supplier of 1933-34 Ford Windshield Rubber
This defect was not because of the installation, that would have given a tearing during the process. everything assembled properly. The rubber gasket was in place perfectly for 1 to 2 years. Then one...
|
|
Forum: Early V8 (1932-53)
07-14-2020, 11:28 AM
|
|
Replies: 19
Views: 4,481
|
|
Forum: Early V8 (1932-53)
07-14-2020, 04:31 AM
|
|
Replies: 19
Views: 4,481
Re: supplier of 1933-34 Ford Windshield Rubber
I installed it..
I totally cleaner out the channel, checked every inch. I did not break during the installation but only after a year or so in place. I noticed the separation along the left edge!
|
|
Forum: Early V8 (1932-53)
07-14-2020, 04:26 AM
|
|
Replies: 19
Views: 4,481
|
|
Forum: Early V8 (1932-53)
07-12-2020, 11:05 AM
|
|
Replies: 19
Views: 4,481
|
|
Forum: Early V8 (1932-53)
07-05-2020, 01:47 PM
|
|
Replies: 19
Views: 4,481
Re: supplier of 1933-34 Ford Windshield Rubber
I tried to superglue the separated area and it held for about 2 hours. I guess the tension was too much for the glue. Do you think jb weld would hold better than superglue. It is hard to glue to...
|
|
Forum: Early V8 (1932-53)
07-04-2020, 02:33 PM
|
|
Replies: 19
Views: 4,481
|
|
Forum: Model A (1928-31)
06-27-2020, 10:21 AM
|
|
Replies: 19
Views: 3,548
|
|
Forum: Model A (1928-31)
06-24-2020, 05:56 PM
|
|
Replies: 17
Views: 3,933
|
|
Forum: Model A (1928-31)
06-21-2020, 09:12 AM
|
|
Replies: 17
Views: 3,933
|
|
Forum: Model A (1928-31)
06-17-2020, 06:00 PM
|
|
Replies: 10
Views: 2,435
|
|
Forum: Model A (1928-31)
06-17-2020, 04:14 PM
|
|
Replies: 10
Views: 2,435
removing distrubutor shaft
Is there a way to remove the distributor shaft without messing up the timing? I am thinking of replacing my head gasket.
|
|
Forum: Early V8 (1932-53)
06-12-2020, 06:55 AM
|
|
Replies: 4
Views: 1,835
Re: 1933 model b pops out of 3 gear into neutral
Thanks..sounds like a great starting point. I have to find my van Pelts transmission book..
It has been a while since I looked at it. I am hoping that it is something I can replace, without removing...
|
|
Forum: Early V8 (1932-53)
06-11-2020, 07:10 AM
|
|
Replies: 4
Views: 1,835
|
|
Forum: Early V8 (1932-53)
05-22-2020, 12:06 PM
|
|
Replies: 15
Views: 2,730
Re: Car transporter?
no one better fully enclosed, best guy you will ever meet.
Bill's Auto Works
Senior Member
|
|
Forum: Early V8 (1932-53)
05-20-2020, 07:30 AM
|
|
Replies: 9
Views: 3,423
Re: HELP with FENDER WELT on 34 Coupe
THis shop has changed hands but used to sell the original type weltting material
Now mike driskol that has the original type stuff
http://fordscript.com/
|
|
Forum: Early V8 (1932-53)
05-04-2020, 01:31 PM
|
|
Replies: 10
Views: 2,208
|
