The Ford Barn

russcc · 02-21-2017, 07:03 PM

Any known sources for good quality USA made new sector shafts, 78-3575
or O1A- 3574 worm gear w/out shaft, or good used ? Also a good source for 78-3576-A sector bushings. I see Dennis Carpenter has the bushings, but they are split. Concerned about splint ones pushing in evenly. Thank you Fordbaners.

Ken/Alabama · 02-21-2017, 07:11 PM

I've used the split bushings with no problems.

TJ · 02-21-2017, 08:51 PM

Try the Early Ford Store in San Dimas Ca. or All Ford Parts In Campbell, Ca. Both have big inventories of NOS parts. Both are listed in the links/vendors section on the V-8 Club website.

Lawson Cox · 02-22-2017, 12:21 AM

What is one of these NOS shafts worth nowadays? I have an extra one I'm probably never going to use.

russcc · 02-22-2017, 07:13 PM

Lawson, Fred Wilner at So Side has NOS, NORS/military ones for $125. for reference. He does not have any worm gears though.

rotorwrench · 02-22-2017, 07:27 PM

Sponsored Links (Register now to hide all advertisements)

The worm gears are reproduced. There was a thread here just the other day about changing them out.

woodiewagon46 · 02-22-2017, 08:40 PM

Anyone know who purchased all of Job Lots stock, they had them, NOS.

Mac VP · 02-22-2017, 08:59 PM

We bought most of their transmission parts stock last year. I know that they didn't have any of the NOS steering sector shaft assemblies.....for several years. I would have bought a bunch if they did. We recently found one and it's available if you don't find it elsewhere.

russcc · 02-23-2017, 09:36 AM

I followed up on a couple leads provided by TJ on Early Ford Parts Store & All Ford Parts in CA. The Store has repop worm gears for $75., as well a repop sectors. Waiting to hear back from All Ford Parts. The original sectors, as I posted, are available from Fred at SO Side. Will advise on what I find out about worm gears.

02-21-2017, 07:03 PM	#1
russcc Senior Member Join Date: May 2010 Posts: 2,871	Source for 37-48 Ford steering sector shaft Any known sources for good quality USA made new sector shafts, 78-3575 or O1A- 3574 worm gear w/out shaft, or good used ? Also a good source for 78-3576-A sector bushings. I see Dennis Carpenter has the bushings, but they are split. Concerned about splint ones pushing in evenly. Thank you Fordbaners.

02-21-2017, 07:11 PM	#2
Ken/Alabama Senior Member Join Date: May 2010 Location: Alabama Posts: 3,455	Re: Source for 37-48 Ford steering sector shaft I've used the split bushings with no problems.

02-21-2017, 08:51 PM	#3
TJ Senior Member Join Date: May 2010 Location: Napa,California Posts: 6,773	Re: Source for 37-48 Ford steering sector shaft Try the Early Ford Store in San Dimas Ca. or All Ford Parts In Campbell, Ca. Both have big inventories of NOS parts. Both are listed in the links/vendors section on the V-8 Club website.

02-22-2017, 12:21 AM	#4
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 7,119	Re: Source for 37-48 Ford steering sector shaft What is one of these NOS shafts worth nowadays? I have an extra one I'm probably never going to use. __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".

02-22-2017, 07:13 PM	#5
russcc Senior Member Join Date: May 2010 Posts: 2,871	Re: Source for 37-48 Ford steering sector shaft Lawson, Fred Wilner at So Side has NOS, NORS/military ones for $125. for reference. He does not have any worm gears though.

02-22-2017, 07:27 PM	#6
rotorwrench Senior Member Join Date: Jun 2010 Location: San Antonio, Texas Posts: 18,007	Re: Source for 37-48 Ford steering sector shaft Sponsored Links (Register now to hide all advertisements) The worm gears are reproduced. There was a thread here just the other day about changing them out.

02-22-2017, 08:40 PM	#7
woodiewagon46 BANNED Join Date: Jun 2012 Location: Long Island,NY Posts: 1,568	Re: Source for 37-48 Ford steering sector shaft Anyone know who purchased all of Job Lots stock, they had them, NOS.

02-22-2017, 08:59 PM	#8
Mac VP Senior Member Join Date: May 2010 Location: Cincinnati, OH Posts: 1,465	Re: Source for 37-48 Ford steering sector shaft We bought most of their transmission parts stock last year. I know that they didn't have any of the NOS steering sector shaft assemblies.....for several years. I would have bought a bunch if they did. We recently found one and it's available if you don't find it elsewhere. __________________ VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com

02-23-2017, 09:36 AM	#9
russcc Senior Member Join Date: May 2010 Posts: 2,871	Re: Source for 37-48 Ford steering sector shaft I followed up on a couple leads provided by TJ on Early Ford Parts Store & All Ford Parts in CA. The Store has repop worm gears for $75., as well a repop sectors. Waiting to hear back from All Ford Parts. The original sectors, as I posted, are available from Fred at SO Side. Will advise on what I find out about worm gears.