The Ford Barn

branch133 · 02-16-2013, 08:03 PM

Installed new inserted engine from Antique Engine and Snyder HC head. Absolutely happy after about 400 miles except clutch will slip when i "get on it" at about 30 mph. I replaced clutch disc and "inspected" the pressure plate.
Am I overlooking something obvious or is it new pressure plate time? Was looking at the new one listed in Snyders. Will this handle all my new "raging power˝?
Bob

Tom Wesenberg · 02-16-2013, 09:05 PM

Are you sure you have correct freeplay?

Maybe your new engine has too much horsepower!

dave in australia · 02-16-2013, 09:23 PM

Does the A clutch plate have an offset centre? I had a 64 Holden that ran fine until I went to take off uphill one day, the clutch slipped and wouldn't grab completely. I nursed it home, figuring the clutch was just worn out. When I got the plate out, the centre had almost been cut through. The centre is offset forward and rear, and it was installed the wrong way around, and I could still read the markings saying which side faces the flywheel. The previous person who installed the plate got it wrong.

branch133 · 02-16-2013, 09:35 PM

Free play is adjusted properly. Never had slipping issue with old engine and worn disc.

redmodelt · 02-16-2013, 09:58 PM

Sponsored Links (Register now to hide all advertisements)

Could be a number of things. The fingers need adjusting, springs are too weak or if the flywheel was surfaced it may not have had the recess for the pressure plate cut down to match what was removed from the face.

02-16-2013, 08:03 PM	#1
branch133 Junior Member Join Date: Apr 2012 Location: Colfax, La 71417 Posts: 12	clutch slipping after new engine Installed new inserted engine from Antique Engine and Snyder HC head. Absolutely happy after about 400 miles except clutch will slip when i "get on it" at about 30 mph. I replaced clutch disc and "inspected" the pressure plate. Am I overlooking something obvious or is it new pressure plate time? Was looking at the new one listed in Snyders. Will this handle all my new "raging power˝? Bob

02-16-2013, 09:05 PM	#2
Tom Wesenberg Senior Member Join Date: May 2010 Location: Mpls, MN Posts: 27,582	Re: clutch slipping after new engine Are you sure you have correct freeplay? Maybe your new engine has too much horsepower!

02-16-2013, 09:23 PM	#3
dave in australia Senior Member Join Date: May 2010 Location: Victoria, Australia Posts: 1,178	Re: clutch slipping after new engine Does the A clutch plate have an offset centre? I had a 64 Holden that ran fine until I went to take off uphill one day, the clutch slipped and wouldn't grab completely. I nursed it home, figuring the clutch was just worn out. When I got the plate out, the centre had almost been cut through. The centre is offset forward and rear, and it was installed the wrong way around, and I could still read the markings saying which side faces the flywheel. The previous person who installed the plate got it wrong.

02-16-2013, 09:35 PM	#4
branch133 Junior Member Join Date: Apr 2012 Location: Colfax, La 71417 Posts: 12	Re: clutch slipping after new engine Free play is adjusted properly. Never had slipping issue with old engine and worn disc.

02-16-2013, 09:58 PM	#5
redmodelt Senior Member Join Date: May 2010 Location: Portland OR Posts: 6,347	Re: clutch slipping after new engine Sponsored Links (Register now to hide all advertisements) Could be a number of things. The fingers need adjusting, springs are too weak or if the flywheel was surfaced it may not have had the recess for the pressure plate cut down to match what was removed from the face.