|
|||||||
| Sponsored Links (Register now to hide all advertisements) |
|
|
![]() |
|
Thread Tools | Display Modes |
|
|
#1 |
|
Senior Member
Join Date: Sep 2024
Location: California
Posts: 121
|
My 1951 Ford convertible has a front brake drum that is 8 oz. out of balance. My Shoebox guru says to forget about it because the imbalance radius is so small, but I am concerned about it. What do you think?
|
|
|
|
|
|
#2 |
|
Super Moderator
Join Date: May 2010
Location: Wisconsin, USA
Posts: 10,541
|
Eight ounces? Eight?
That's a LOT. Are you sure it is eight ounces? Eight grams perhaps?
__________________
"I can explain it for you. However, I can't understand it for you". |
|
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
|
|
#3 |
|
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 6,581
|
If it is too unbalanced it will show up in the ride and tires.
|
|
|
|
|
|
#4 |
|
Senior Member
Join Date: Sep 2024
Location: California
Posts: 121
|
I used a magnet, bolts, and a postal scale to determine the imbalance; it was 8 oz.
|
|
|
|
|
|
#5 |
|
Senior Member
Join Date: May 2010
Location: middle of Iowa
Posts: 1,001
|
I used JB Weld to attach a 1/4” chunk of steel to the outer surface of a 40 front drum on my car a few seasons ago. Hasn’t fallen off yet.
|
|
|
|
|
|
#6 |
|
Senior Member
Join Date: Sep 2024
Location: California
Posts: 121
|
Sponsored Links (Register now to hide all advertisements)
|
|
|
|
|
|
#7 |
|
Senior Member
Join Date: Jan 2011
Location: Beverly Kansas
Posts: 5,557
|
I would grind off whats needed if you have a way to static balance them, like on the spindle with dry bearings set loose.
|
|
|
|
|
|
#8 |
|
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 2,156
|
Take it to shop where they balance engines; should be able to fix it right up.
|
|
|
|
|
|
#9 | |
|
Super Moderator
Join Date: May 2010
Location: Wisconsin, USA
Posts: 10,541
|
Quote:
I'm still trying to comprehend an eight ounce out of balance condition. That's huge!
__________________
"I can explain it for you. However, I can't understand it for you". |
|
|
|
|
|
|
#10 |
|
Senior Member
Join Date: May 2010
Posts: 5,394
|
Any engine rebuilder should be able to guide you to a balance shop.
|
|
|
|
|
|
#11 |
|
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 3,024
|
I can’t believe something isn’t visible…..8 oz doesn’t sound like a lot…until you call it “half a pound”!….on that small of a diameter …..any tires I’ve balanced take 2-4 oz…..but the diameter is so much more….can you show us the method for checking it that you’re using?………Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver…RIP |
|
|
|
|
|
#12 |
|
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,672
|
How much oversized is the drum? might be better to buy new instead of paying to have it balanced
|
|
|
|
|
|
#13 |
|
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 12,137
|
|
|
|
|
|
|
#14 | ||
|
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 2,156
|
Quote:
Quote:
I found repop drums listed that look to be Argentina full cast iron. I have seen one of those; but for an F-1, that machined "off center" which leaves one side of the drum thicker than the other. Could very well be way heavy on one side. |
||
|
|
|
|
|
#15 |
|
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 3,024
|
Comment Deleted
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver…RIP Last edited by flatford8; 10-30-2024 at 04:51 PM. Reason: Reread last post |
|
|
|
|
|
#16 |
|
Senior Member
Join Date: May 2010
Posts: 5,313
|
Before I became a Boling Bros dealer I was using Lincoln drums that were foreign made from another manufacturer and out of balance drums were common. Fortunately I only sold maybe a dozen pairs of them on customer chassis before going to the Boling USA made drums. No further problems. I did my best to help the customers with the bad drums. Most of them had them spin balanced with the tire and wheel on the car.
|
|
|
|
|
|
#17 |
|
Senior Member
Join Date: May 2010
Location: NJ
Posts: 7,227
|
|
|
|
|
![]() |
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|