Dead in the road

[vern hodgson]

Left garage on a four mile cruise, two miles in, engine cuts out and restarts happened second time, restarted, third time no go, no lites, no horn but turns over. Where to look, terminal box, switch?

[Bob from Northport]

Check the ignition wire that runs from the starter to the generator for power. Is there a fuse in the engine compartment??

[vern hodgson]

No fuse, will check wire later today, to hot, to tired. Thanks.

[Doug Linden]

If you have working.a test light, start at the terminal on the starter switch and follow the wires to see where the light stops. That should give you a answer where the problem is located.

[GRutter]

If no fuse as Bob suggested, then jump the two terminals together in the firewall junction box. That will bypass the Amp Meter. Repro meters are failure prone, and fits your description of no lights, no horn, no ignition, but turns over.

[vern hodgson]

Sponsored Links (Register now to hide all advertisements)

Originally Posted by GRutter

If no fuse as Bob suggested, then jump the two terminals together in the firewall junction box. That will bypass the Amp Meter. Repro meters are failure prone, and fits your description of no lights, no horn, no ignition, but turns over.

First thing in the am,thanks

[Patrick L.]

I carry an old distributor primary cable end with the armor stripped off and a spring clip attached.

A jumper lead as GR suggests is a good thing to carry around.

[burner31]

Originally Posted by Patrick L.

I carry an old distributor primary cable end with the armor stripped off and a spring clip attached.

A jumper lead as GR suggests is a good thing to carry around.

I have one also
Back in the day the cops would pinch you for having one of those

[warrene]

Yea' ... repro' ammeters are JUNK, I finally found an old one on eBay, end of problems.

[old31]

Originally Posted by GRutter

If no fuse as Bob suggested, then jump the two terminals together in the firewall junction box. That will bypass the Amp Meter. Repro meters are failure prone, and fits your description of no lights, no horn, no ignition, but turns over.

Just so I undestand. Do you mean you are putting a jumper on both the driver and passenger side of the dogbones?

[Patrick L.]

Originally Posted by burner31

I have one also
Back in the day the cops would pinch you for having one of those

Really ? Interesting. I didn't know that.

[Gary WA]

Is your road still dead?

[Chuck Sea/Tac]

It must be”stinking to high heaven” by now.

Seriously, any luck yet?

[Fred K OR]

May be coil. I had similar problem and it was coil. Just guess.

[GRutter]

Originally Posted by old31

Just so I undestand. Do you mean you are putting a jumper on both the driver and passenger side of the dogbones?

Yes - across both terminals in the junction box. If you look at the wiring diagram, jumping the two terminals does nothing more than eliminate the ammeter.

[vern hodgson]

So… dropped t box cover, no juice on either terminal, inspected wires all seem ok, laid a wrench across t box studs and hit the horn button. She sounded off like a new bride on her honeymoon. Replaced ammeter. Now to find an original.

[vern hodgson]

Originally Posted by vern hodgson

So… dropped t box cover, no juice on either terminal, inspected wires all seem ok, laid a wrench across t box studs and hit the horn button. She sounded off like a new bride on her honeymoon. Replaced ammeter. Now to find an original.

So a big THANKS to every one. What a feeling to conquer the dreaded electrical monster

[GRutter]

Originally Posted by vern hodgson

So a big THANKS to every one. What a feeling to conquer the dreaded electrical monster

Glad you got it solved. Just follow the wiring diagrams. Model A wiring is relatively simple even for the 'electrically challenged'. It's not a monster - you just keep nibbling at it until it you nail it.