Forum: Early V8 (1932-53)
05-01-2024, 07:25 PM
|
|
Replies: 10
Views: 599
|
|
Forum: Early V8 (1932-53)
05-01-2024, 04:18 PM
|
|
Replies: 10
Views: 599
Re: Old brazed repairs on a 21 stud
Oh, I'm gonna pressure wash the heck out of it after I pull the valves today for sure. Then it'll go over to Harrell Engines LA & Alec can take a look at it, he's a real good guy to know in the...
|
|
Forum: Early V8 (1932-53)
05-01-2024, 03:28 PM
|
|
Replies: 10
Views: 599
Re: Old brazed repairs on a 21 stud
It's a 35 or 36 block, babbitt bearings not inserts. I'll probably have a little bit of test done on it, I always hate to throw a block away if it can be saved, Ford's not making them anymore, right?
|
|
Forum: Early V8 (1932-53)
05-01-2024, 12:56 PM
|
|
Replies: 10
Views: 599
Old brazed repairs on a 21 stud
Hi,
I'm tearing down this old block that's been out of service a long long time apparently. Everything looks pretty good inside, bearings are actually pretty nice, nothing was too loose or floppy,...
|
|
Forum: Early V8
04-23-2024, 04:03 PM
|
|
Replies: 1
Views: 285
|
|
Forum: Early V8
02-12-2024, 04:53 PM
|
|
Replies: 1
Views: 285
|
|
Forum: Early V8 (1932-53)
02-01-2024, 01:02 PM
|
|
Replies: 8
Views: 620
|
|
Forum: Early V8 (1932-53)
01-31-2024, 05:57 PM
|
|
Replies: 8
Views: 620
Mystery Crank Pulley
I had to buy two pulleys to get the one that I needed, wouldn't separate. The seller did not know the origin of the mystery pulley, please let me know if you recognize it, thanks!
|
|
Forum: Early V8 (1932-53)
01-31-2024, 05:51 PM
|
|
Replies: 3
Views: 403
Clutch disk question
Soo I got the motor and trans separated, it appears to me to be a 36-39 gearset. I quickly put a tape measure on the disk as I was turning out the lights and I'm pretty sure it's 9" or so. who's the...
|
|
Forum: Early V8 (1932-53)
01-31-2024, 05:47 PM
|
|
Replies: 7
Views: 909
Re: Remove Trans from 21 stud 36 flattie
Got it, pilot bearing was stuck, had to unbolt clutch basket through inspection plate and then it came apart easy. That bearing is really, really stuck on the end of that input shaft.
The bearing is...
|
|
Forum: Model A (1928-31)
01-31-2024, 03:56 PM
|
|
Replies: 3
Views: 409
Re: Mystery Crank Pulley
The crank snout is certainly bigger. The seller said he thought maybe it was a Mercury but I don't know. The wiper groove should be a big tell.
|
|
Forum: Model A (1928-31)
01-31-2024, 02:16 PM
|
|
Replies: 3
Views: 409
Mystery Crank Pulley
sorry all, posted this in the wrong forum, intended for Early V8 -
I had to buy two pulleys to get the one that I needed, wouldn't separate. The seller did not know the origin of the mystery...
|
|
Forum: Early V8 (1932-53)
01-30-2024, 11:05 PM
|
|
Replies: 73
Views: 4,950
Re: T5 advice
Probably a ford 8 inch, I have a couple laying around.
|
|
Forum: Early V8 (1932-53)
01-29-2024, 04:39 PM
|
|
Replies: 14
Views: 806
|
|
Forum: Early V8 (1932-53)
01-23-2024, 04:52 PM
|
|
Replies: 14
Views: 806
|
|
Forum: Early V8 (1932-53)
01-23-2024, 02:25 PM
|
|
Replies: 14
Views: 806
|
|
Forum: Early V8 (1932-53)
01-23-2024, 12:58 PM
|
|
Replies: 14
Views: 806
Ford 1935 - 1940 Open Car Door Latch
An eBay vendor mislabeled a part and sent me a open car door latch instead of a 1937 trunk latch. My bad for not paying more attention.
Any idea of the value to list it at? It seems to work fine...
|
|
Forum: Early V8 (1932-53)
01-22-2024, 02:17 AM
|
|
Replies: 73
Views: 4,950
Re: T5 advice
Good info all, thanks! The various T5 threads out there have great info, it’s a firehose though. So it’s good to get zero’d in with the fellow flatties who have the specific knowledge.
|
|
Forum: Early V8 (1932-53)
01-21-2024, 01:27 PM
|
|
Replies: 73
Views: 4,950
T5 advice
So I’ve read the T5 threads, I’m looking to have one built.
It sounds like to me I want a WC pre 93 S10 Chevy bolt pattern 14 spline input 26 spline output 3.76 mechanical speedo box to go behind...
|
|
Forum: Early V8 (1932-53)
01-21-2024, 02:53 AM
|
|
Replies: 7
Views: 909
|
|
Forum: Early V8 (1932-53)
01-19-2024, 12:46 AM
|
|
Replies: 7
Views: 909
Remove Trans from 21 stud 36 flattie
I swear I saw a thread about getting a stock trans off of a 21 stud block when the trans is not coming off. Looks like I got all the bolts out of the bellhousing, I took the motor and trans out of...
|
|
Forum: Early V8 (1932-53)
01-18-2024, 04:39 PM
|
|
Replies: 14
Views: 936
Re: 1937 Philco 1440
Great stuff! It's a neat old piece, I'm going to give it a chance to get going :)
|
|
Forum: Early V8 (1932-53)
01-18-2024, 04:36 PM
|
|
Replies: 6
Views: 441
|
|
Forum: Early V8 (1932-53)
01-16-2024, 06:37 PM
|
|
Replies: 6
Views: 441
|
|
Forum: Early V8 (1932-53)
01-16-2024, 04:41 PM
|
|
Replies: 6
Views: 441
|
