Forum: Late V8 (1954+)
Yesterday, 08:20 PM
|
Replies: 25
Views: 670
Re: 56 TBird
I'll end my responses by saying you need help. Maybe another banishment will be that help. I understand you have more than one ??
.
|
Forum: Late V8 (1954+)
Yesterday, 10:49 AM
|
Replies: 9
Views: 241
|
Forum: Late V8 (1954+)
Yesterday, 10:36 AM
|
Replies: 25
Views: 670
|
Forum: Late V8 (1954+)
Yesterday, 10:28 AM
|
Replies: 25
Views: 670
Re: 56 TBird
He is not "calling out' on the timing cover. He is just stating a fact of what he is using. Why are you "calling out" about a simple statement he made.
Get real and stick to facts.
I...
|
Forum: Late V8 (1954+)
06-03-2024, 06:50 PM
|
Replies: 9
Views: 241
|
Forum: Late V8 (1954+)
06-03-2024, 06:47 PM
|
Replies: 25
Views: 670
Re: 56 TBird
It's had to see your fascination over the fact that he is using a truck (or service part) timing cover. May be he is not a fanatic over "correct" parts.
|
Forum: Early V8 (1932-53)
06-02-2024, 06:48 PM
|
Replies: 14
Views: 534
Hand Opersted Tachometer ??
There is an ad in the Late V8 for sale for a Hand Operated Tachometer. In all my years that is a new one for me. What would this be used for
|
Forum: Early V8 (1932-53)
05-31-2024, 02:31 PM
|
Replies: 7
Views: 416
|
Forum: Early V8 (1932-53)
05-29-2024, 06:40 PM
|
Replies: 9
Views: 419
|
Forum: Late V8 (1954+)
05-23-2024, 09:53 PM
|
Replies: 4
Views: 226
|
Forum: Late V8 (1954+)
05-20-2024, 07:17 PM
|
Replies: 4
Views: 174
Re: 54 Mercury skirt gasket
I use the 3M weatherstrip adhesive. Is there any small holes where the gasket goes? If so, they were held by staples. I've used both on my 56 Tbird. Glued the gasket down and then used the...
|
Forum: Questions & Suggestions
05-15-2024, 07:43 PM
|
Replies: 1
Views: 197
Re: Fuse sizes
Only questions about the site are to be posted here.
However, your owners manual may have a listing for all the fuses. If you don't have one, try ebay for it. Or get a Shop manual
|
Forum: Late V8 (1954+)
05-14-2024, 07:11 PM
|
Replies: 11
Views: 563
Re: Mercury 312
Stock spec for rocker arm gap,is .019. See if you can locate the noisy rocker and make sure the push rod goes up and down
|
Forum: Late V8 (1954+)
05-14-2024, 07:08 PM
|
Replies: 5
Views: 283
Re: Windlace clip
Try Restoration Specialties in PA. They have lots of hardware items.
|
Forum: Early V8 (1932-53)
05-13-2024, 07:37 PM
|
Replies: 10
Views: 718
Re: pertronix distributor
The stock 53 carb vacuum source will not work with the Pertronix. The stock vacuum is very low while the Pertronic will require a stronger vacuum "pull" and is usually connected to a source below...
|
Forum: Late V8 (1954+)
05-11-2024, 03:54 PM
|
Replies: 8
Views: 388
Re: 1955 Ford Customline Power Steering Filter
One thing to watch out for and that is filter size. The early 50's cars used a bigger filter than later cars (No idea of the cutoff). Using the later, smaller filter in a car that used the larger...
|
Forum: Late V8 (1954+)
05-09-2024, 07:22 PM
|
Replies: 15
Views: 608
|
Forum: Early V8 (1932-53)
05-09-2024, 07:08 PM
|
Replies: 14
Views: 719
|
Forum: Early V8 (1932-53)
05-09-2024, 07:06 PM
|
Replies: 14
Views: 719
|
Forum: Late V8 (1954+)
05-08-2024, 07:21 PM
|
Replies: 15
Views: 608
|
Forum: Late V8 (1954+)
05-07-2024, 08:11 PM
|
Replies: 15
Views: 608
Re: '59 Fuel Pump Issue
A source for a rebuild of yours is AG Rebuilders in Massachusetts. I have had a few done by them with no problems.
|
Forum: Early V8 (1932-53)
05-03-2024, 07:48 PM
|
Replies: 4
Views: 230
|
Forum: Early V8 (1932-53)
05-03-2024, 03:08 PM
|
Replies: 4
Views: 230
|
Forum: Early V8 (1932-53)
05-03-2024, 03:05 PM
|
Replies: 5
Views: 356
|
Forum: Late V8 (1954+)
05-02-2024, 07:08 PM
|
Replies: 9
Views: 464
Re: 1954 Mercury underhood question
No hood prop for a 54 mercury from the factory if it's the same as my 54 Ford. 54's had very poor hinges plus you may be missing some springs at the hinge. There are two, one a typical coil and a...
|