Forum: Early V8 (1932-53)
05-06-2024, 04:46 AM
|
Replies: 12
Views: 863
|
Forum: Early V8 (1932-53)
04-18-2024, 05:14 AM
|
Replies: 3
Views: 581
Re: alameda, ca swap meet???
You can try Treasure Island there is lots of available space call Rich with TIDA
415 297-3112
Biggie crane has a big empty hanger on the island too there advertising renting I’m sure they would...
|
Forum: Early V8 (1932-53)
12-17-2023, 11:50 AM
|
Replies: 18
Views: 1,228
Re: Need help ftting rear glass? 39 truck
Hello, Im by far no expert. I took my rear glass out to replace the gasket a couple years ago I installed the new gasket on the window and wrapped a 3/16 nylon cord in the body groove lubed it up...
|
Forum: Early V8 (1932-53)
12-02-2023, 06:38 AM
|
Replies: 120
Views: 9,348
Re: Shoud I relieve my block
I’m no expert however I do have bunch of old literature from early days of Harley Davidson on their development of the side valves. All their successful racing engines had a relief area.
Hopping up...
|
Forum: Early V8
07-28-2021, 05:41 AM
|
Replies: 0
Views: 512
Wanted 8’ express bed
Wanted 8’ bed for 1938-1942 Ford tonner. Will use wider post ‘42 if available
Thanks
|
Forum: Early V8 (1932-53)
05-15-2021, 09:01 AM
|
Replies: 3
Views: 972
Re: A 41 Ford Truck Comes Home
What a great story. Like most of us we all have something that started us on our our
old vehicle path. As a kid in the mid to late 60’s we went to a camp, the owner would “Let” us kids haul the...
|
Forum: Early V8
05-15-2021, 07:20 AM
|
Replies: 0
Views: 337
Two Bolt Timing cover
Need to buy a good two bolt timing Cover for a 1947 Flathead V8 tonner
Also need a choke rod for same truck. PayPal check or money order.
PM or email
[email protected]
Thanks
|
Forum: Early V8 (1932-53)
05-07-2021, 05:44 PM
|
Replies: 20
Views: 6,348
Re: 1940 3/4 ton pickup
Hello, Real Nice Truck, definitely a ‘40. Tonner Express. Definitely a 3/4 hauler. These are great trucks. I got my brakes at Napa.
The wheels are of the wide five pattern, but are wider than cars...
|
Forum: Early V8
04-24-2021, 09:18 AM
|
Replies: 0
Views: 507
Harmon Collins
Hello, I need to purchase a timing plate for a Harmon Collins magneto on a 3 bolt 1940 Ford truck. Any leads would be appreciated
Thank you
|
Forum: Early V8 (1932-53)
04-24-2021, 09:15 AM
|
Replies: 62
Views: 13,513
|
Forum: Early V8 (1932-53)
03-17-2018, 07:32 AM
|
Replies: 8
Views: 1,324
Re: 1939 pickup firewall insulation
Hello, I am not finding an answer to a question That's most likely been asked. Does anyone make original type cardboard firewall pad not the ABS ??
|
Forum: Early V8
03-08-2018, 07:11 AM
|
Replies: 0
Views: 902
1940 Truck dash Knobs
Hello, I am needing a set of original Lights, Choke and Throttle knobs for a 1940
Truck, Will pay $70 plus shipping for a good set.
|
Forum: Early V8 (1932-53)
06-25-2017, 08:59 PM
|
Replies: 12
Views: 1,845
|
Forum: Early V8 (1932-53)
06-25-2017, 08:24 PM
|
Replies: 12
Views: 1,845
|
Forum: Early V8 (1932-53)
06-25-2017, 08:07 PM
|
Replies: 12
Views: 1,845
Re: 1940 Ford Tonner production numbers
Hello, Yes it is most deffinately 18-BB and ends 9Y. so is my father inlaw's ton an a half. BB is big truck single B is four cylinder. Both of these trucks where bought new localy here in western...
|
Forum: Early V8 (1932-53)
06-25-2017, 02:48 PM
|
Replies: 12
Views: 1,845
Re: 1940 Ford Tonner production numbers
Hello, I have the 17" wheels that came with the truck, but I also picked up a set of 16". Lots of tire options. I have been talking with another guy who might be parting with a set of 20" wheels. If...
|
Forum: Early V8 (1932-53)
06-25-2017, 01:36 PM
|
Replies: 28
Views: 8,931
|
Forum: Early V8 (1932-53)
06-25-2017, 01:29 PM
|
Replies: 12
Views: 1,845
Re: 1940 Ford Tonner production numbers
Could my father inlaw's estimate forgotten a zero?? I have seen a 122" wheel base trucks over the years so 2500 seems short, I saw in a thread source 1/2 ton numbers but could find anything for 1 ton.
|
Forum: Early V8 (1932-53)
06-25-2017, 12:41 PM
|
Replies: 12
Views: 1,845
1940 Ford Tonner production numbers
Hello Everyone !! New to the forum this past year, just been reading great info. I own and have owned several old rides, both with four wheels and two. Travel a lot for work so I get to hit many swap...
|