Forum: Early V8 (1932-53)
Today, 11:12 PM
|
Replies: 11
Views: 481
Re: 1935 front motor mount
In 1937, Ford redesigned the inlet manifold, lowering the generator mount. As the fan was now lower, they could increase its diameter, but also changed the distributor coil to provide clearance......
|
Forum: Early V8 (1932-53)
Today, 09:58 PM
|
Replies: 1
Views: 29
it came home
I attended a swap meet last weekend and found a relieved 99 engine, minus heads, front cover etc, that had been modified in the way I tend to build an engine; it had been modified for external oil...
|
Forum: Early V8 (1932-53)
Today, 01:54 AM
|
Replies: 12
Views: 356
|
Forum: Early V8 (1932-53)
Today, 12:28 AM
|
Replies: 11
Views: 481
Re: 1935 front motor mount
so the 37 style pump i put on the engine will not work. I have 37 style heads.
what would i have to change to make them work?
Rest assured, it will all bolt up, 37 water pump mount...
|
Forum: Early V8 (1932-53)
05-19-2024, 01:35 PM
|
Replies: 10
Views: 455
|
Forum: Early V8 (1932-53)
05-18-2024, 10:05 PM
|
Replies: 10
Views: 455
Re: 1934 hydraulic rear brakes
What about the B- wheel bearing vs The 68- ?
Just use the appropriate bearings to suit the hubs. The axle housings /inner races are all the same dia.
If you use the BB brakes on rear,...
|
Forum: Early V8 (1932-53)
05-18-2024, 04:35 AM
|
Replies: 14
Views: 709
|
Forum: Early V8 (1932-53)
05-15-2024, 01:34 AM
|
Replies: 91
Views: 3,303
Re: My next flathead build?
That is a C59A block... in the C69A block, the top row of coolant holes are oval/elongated...whereas the C59A block has round holes as pictured in post #20 in this thread.
|
Forum: Early V8 (1932-53)
05-11-2024, 12:19 AM
|
Replies: 11
Views: 524
Re: Was at the Gilmore last week
I have had the honour of riding in an '03 Model A. [also an '03 Oldsmobile, very similar]. This particular model A # 486, was imported in 1904 by John J. Boyd. He bequeathed the car to a relative,...
|
Forum: Early V8 (1932-53)
05-10-2024, 03:17 AM
|
Replies: 38
Views: 2,343
|
Forum: Early V8 (1932-53)
05-10-2024, 12:28 AM
|
Replies: 7
Views: 477
2 overdrives
Is anyone on here running two overdrives in an early Ford? Call me mad if you will, but I currently have a fixation on overdrives. I currently run a Columbia in my 35 sedan...when I first fitted it,...
|
Forum: Early V8 (1932-53)
05-07-2024, 12:48 AM
|
Replies: 16
Views: 720
|
Forum: Early V8 (1932-53)
05-07-2024, 12:43 AM
|
Replies: 16
Views: 600
Re: How to disassemble a Columbia rearend
Yes, 4.44:1 is standard ratio with Lincoln Zephyr. I believe, after looking at your pictures posted, that your diff is actually 38-39 Lincoln Zephyr...it is a hypoid rear, which first came out in...
|
Forum: Early V8 (1932-53)
05-05-2024, 09:31 PM
|
Replies: 16
Views: 600
Re: How to disassemble a Columbia rearend
You need to remove the regular LH housing from the banjo. Then, undo the bolts holding the crownwheel. Then you can remove crownwheel and LH axle. Then you can see the spider gears etc, move that...
|
Forum: Early V8 (1932-53)
05-02-2024, 09:13 PM
|
Replies: 6
Views: 607
Re: Lincoln pinion backlash
thank you Ken and Pete, I actually set it all up and fitted it a week ago by reading the gear mesh pattern. A bit of work with the Columbia, I had to fit a .005" shim behind the Columbia side bearing...
|
Forum: Early V8 (1932-53)
05-02-2024, 01:51 PM
|
Replies: 6
Views: 594
|
Forum: Early V8 (1932-53)
04-28-2024, 11:03 PM
|
Replies: 22
Views: 1,125
|
Forum: Early V8 (1932-53)
04-27-2024, 11:54 PM
|
Replies: 95
Views: 6,248
|
Forum: Early V8 (1932-53)
04-24-2024, 01:56 AM
|
Replies: 3
Views: 493
Re: Lincolin Zephyr gears
22 tooth, confused now? Look here; http://www.vanpeltsales.com/FH_web/flathead_trans-gearratios.htm
|
Forum: Early V8 (1932-53)
04-24-2024, 12:21 AM
|
Replies: 19
Views: 1,629
Re: Compression and flow
Assemble your short block, then machine the heads to achieve the desired .040" odd thou quench. Getting that clearance from top of piston at TDC to head to within .040-.050" is paramount for optimum...
|
Forum: Early V8 (1932-53)
04-22-2024, 11:04 PM
|
Replies: 6
Views: 607
Lincoln pinion backlash
I'm in the process of setting up a Lincoln [hypoid] rear end. I'm quite familiar with how to set up a banjo rear, having done numerous Fords over the years, but I don't know the specs for backlash...
|
Forum: Early V8 (1932-53)
04-22-2024, 12:02 AM
|
Replies: 20
Views: 1,476
|
Forum: Early V8 (1932-53)
04-20-2024, 02:22 AM
|
Replies: 4
Views: 480
|
Forum: Early V8 (1932-53)
04-19-2024, 12:58 AM
|
Replies: 4
Views: 480
oil type recommendation
I'm converting a Lincoln [hypoid] rear end to Columbia, hypoid rear ends have special additives, the Columbia contains yellow metal components. So, what oil specification do I put into this thing?...
|
Forum: Early V8 (1932-53)
04-18-2024, 12:27 AM
|
Replies: 19
Views: 1,629
Re: Compression and flow
There is a wealth of information about this matter in both printed form and on the internet. Ronnie above makes a valid point which backs up my comments....[Hemis] . Obviously, if one could achieve...
|