The Ford Barn

The Ford Barn (https://www.fordbarn.com/forum/index.php)
-   Model A (1928-31) (https://www.fordbarn.com/forum/forumdisplay.php?f=3)
-   -   Whet do you do here? (https://www.fordbarn.com/forum/showthread.php?t=50311)

Terry, NJ 10-14-2011 12:29 AM
Whet do you do here?
 

First off, I can't show a picture, I can't get a pic to load. This deals with the last/rear cross piece of wood that fits on the sub rails of my 30, Town Sedan. There are two short (about 3") steel channel/clamps pieces at both sides with four bolts each. My problem is that the channels/clamps won't go over the new wood. I've got to grind about 1/8 of an inch off the wood for the channels to fit.
1) Is it best to take it off the top or bottom of the wooden cross piece?
2) What do these channels/clamps do? I can't see how they serve any purpose. I'm sure that's not the case, but what do they do?
Terry

Marco Tahtaras 10-14-2011 09:53 AM
Re: Whet do you do here?
 

It sounds like Briggs body. Do you have the original wood to compare? If that cross sill is too thick are the side sills also too thick? If so it can cause minor problems elsewhere. Those brackets support the rear bumper arms. The rear most bolts clamp the brackets tightly and the forward holes align with the bumper arms. Yes, you want them there.

Mike V. Florida 10-15-2011 12:31 AM
Re: Whet do you do here?
 

Quote:
Originally Posted by Terry, NJ (Post 288762)
First off, I can't show a picture, I can't get a pic to load. This deals with the last/rear cross piece of wood that fits on the sub rails of my 30, Town Sedan. There are two short (about 3") steel channel/clamps pieces at both sides with four bolts each. My problem is that the channels/clamps won't go over the new wood. I've got to grind about 1/8 of an inch off the wood for the channels to fit.
1) Is it best to take it off the top or bottom of the wooden cross piece?
2) What do these channels/clamps do? I can't see how they serve any purpose. I'm sure that's not the case, but what do they do?
Terry
Terry do you think you could email me pictures? I would then post them for you.

FL&WVMIKE 10-15-2011 09:40 AM
Re: Whet do you do here?
 

Quote:
Originally Posted by Terry, NJ (Post 288762)
First off, I can't show a picture, I can't get a pic to load. This deals with the last/rear cross piece of wood that fits on the sub rails of my 30, Town Sedan. There are two short (about 3") steel channel/clamps pieces at both sides with four bolts each. My problem is that the channels/clamps won't go over the new wood. I've got to grind about 1/8 of an inch off the wood for the channels to fit.
1) Is it best to take it off the top or bottom of the wooden cross piece?
2) What do these channels/clamps do? I can't see how they serve any purpose. I'm sure that's not the case, but what do they do?
Terry
Terry NJ ..............................
Did you resize your image down to 800 pixals wide ? If not, Fordbarn will not take them and won't tell you why.
MIKE :)

Terry, NJ 10-15-2011 07:51 PM
Re: Whet do you do here?
 

Thanks for the response. Correct! It is a Briggs. So from what you're saying, I would want to maintain the the surface on the bottom and remove any wood from the top of the sill, Am I correct about this?
Terry




Quote:
Originally Posted by Marco Tahtaras (Post 288886)
It sounds like Briggs body. Do you have the original wood to compare? If that cross sill is too thick are the side sills also too thick? If so it can cause minor problems elsewhere. Those brackets support the rear bumper arms. The rear most bolts clamp the brackets tightly and the forward holes align with the bumper arms. Yes, you want them there.

Terry, NJ 10-15-2011 07:57 PM
Re: Whet do you do here?
 

Quote:
Originally Posted by Mike V. Florida (Post 289301)
Terry do you think you could email me pictures? I would then post them for you.
I'l try! My problem is not with Ford Barn, It's with the Kodak camera/software that doesn't allow me to pick out single pics . I'll give it a shot though! Thanks again.
Terry


All times are GMT -5. The time now is 10:03 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.