Re: model A and model B lifters I don't expect that a reground cam would last as long as a nos A or B cam. Some of the surface hardness would be removed. The better cam grinders don't remove that much from the tip of the lobe and the tip of the lobe is what counts. It is usually lift that is most important to most. the amount that is removed from the heel of the cam only adds to the lift and the heel of the cam is where the adjustment begins. the heel of the cam is not under valve spring pressure. Jim Brierly, the famous cam grinder that posts here has stated that the amount of surface hardness that is removed will make little difference. I don't expect to put another 50.000 miles on any of my model A's in my lifetime anyway. I've got two reground 3/4 race Winfield grinds from Bill Stipe that are performing and holding up very good. The cam in my speedster was installed twelve years ago and the one in the roadster has been running five years so far. Ive got a model B cam that was NOS when I installed it in my speedster in the early ninties. This engine is sitting in the back corner of my shop. This engine was still running when I removed it. I just replaced it with a more powerful engine with the reground 3/4 race cam. Maybe it wasn't the cam alone that made the difference. I have used the single lock adjustable lifters with every engine that I have done except one.
|
Re: model A and model B lifters Quote:
That doesn't sound like a NOS cam. The production era cams were forged and heat treated. The steel had a fairly high carbon content at .4%-.45%. The heat treatment provided a controlled displacement of the carbon. These were all bare steel. "B" cams supplied by Ford later were made from billet and carburized for hardening which is essentially inducing carbon to a base metal with only about .2% carbon. This is a form of case hardening. These were copper plated everywhere except the lobe and journal surfaces. The copper protected the other areas from the surface hardening which would otherwise become brittle. These cams came originally with shiny steel lobes similar to what you would get from Bill Stipe or in the past from Harvey Crane. Your cam still could be NOS and someone just messed with it before you got it. One sure way to tell is to put a straight edge across to journals, positioned over the tip of one lobe. If it is unused and unmolested there will only be about .001" between your lobe tip and the straight edge. |
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters In 1972 I worked at a place in Spokane Wa called Unit Engineering, an engine rebuild machine shop. I spent quite a bit of time on the cam grinder. Most all of the cams we ground had a taper to the lobe and the lifters were slightly parabolic on the bottom. If you held two new lifters bottom to bottom, they only contacted each other in the center. This taper of the cam lobe and "rounded" bottom of the tappet is what cause the lifter (and pushrods in ohv engines) to rotate when running. This created more of a bearing action than a wiping action We never hardened our regrinds but did tape the bearing journals with masking tape for protection and then immerse the freshly ground cam in a heated parkerizing solution for a time. This made the cam lobe turn black and take on an acid induced textured surface which would help hold oil and aid in turning the lifter. Never ground an A or T cam but assume they would be engineered the same.
|
Re: model A and model B lifters Did anyone notice that in the diagram Marco posted (is this from Ford service bulletin?) the B-6500 length is apparently greater, but the dimensions are not correct. Were these checked against the original drawings? Are the numbers correct but just in the wrong places?
|
Re: model A and model B lifters "Also, I've been told/informed (by cam people, in answer to my Q re reground cams) that NO ONE rehardens the surface on 'reground cams'. Anyone have an opinion whether that is TRUE?"
False. Many cam grinder's reharden reground cams, both steel and cast iron. For mild street grinds on steel cams such as the model A/B there is not enough material taken off to go through the original hardening which is usually.080 to .090 deep. The black or brown finish on some cams is Parkerizing. It is not original as Marco has said. It is however very helpful in prolonging the life of the cam. It helps to retain oil for initial break in. It is best applied to cast iron cams. Steel cams do not benefit as much. Purdy: A reground cam will last just a long as a new one if done properly. "Been in the cam business 59 years" |
Re: model A and model B lifters Thanks Pete, I was really hoping that a respected cam grinder, like you would speak up on this matter. Reground cams have really been hammered to hell by two or three individuals on this forum. I'm not necessarily reffering to Herm.
|
Re: model A and model B lifters Quote:
Yup noticed that the number looked to be 'out of place' for the drawings. Mabe 'transposed/reversed' :confused: |
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters Thanks Herm, It was not my intention to try and cause you to eat crow, or discredit your posts. This thread started out with the question by Jose Cartin if he could use model A lifters with a model B cam. I answered Jose and said that model B lifters had a larger base and were also longer than model A lifters. I suggested that if he used a model B cam that he would either need to use model B lifters or adjustable lifters. I also pointed out the fact that the double lock lifters that I have seen had a smaller base. I also pointed out the danger of smaller base lifters dropping of the nose of the cam quicker and scrapeing down the side of the lobe and causeing rapid wear. This was backed up by Ford and Vince Falters site. I was only trying to give helpful advice. Undoubtabtly Jose didn't see my answer or ignored it completely and asked the same question again. Another guy came on and said that he used MODEL A lifters with B cams on his rebuilds all of the time and bumped his post to the top. Maybe he does use model A lifters, I wouldn't doubt it. Maybe in an attempt to deminish my post on the previous thread, the guy really put his foot in his mouth. He was probably meaning that he used adjustable lifters. Just because adjustable lifters are listed in the model A parts catalogs doesn't mean that they are original model A or B lifters, neither left the factory with adjustable lifters. Also not to critisize but the lifters pictured on Ford Garage are all adjustable lifters and don't reflect the difference between original model A and B lifters. Then the thread turned to cam hardness and the poor quality of reground cams and the people that really couldn't afford a good cam. I felt that I had to keep coming back time after time to defend my cams and my credability. Nothing That I said was intended to discredit anybody. Just talking model A and trying to share my experiences and give helpful advice.
Thanks Purdy. |
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters Thanks Herm, I agree.
|
Re: model A and model B lifters Quote:
|
Re: model A and model B lifters Quote:
A "B" cam is a "B" cam but once it's reground it can be almost anything regardless of what name is placed on it. To start with, the lobes are SMALLER. It's worth noting (again) that it's impossible to duplicate ALL the characteristics of any given cam lobe at a reduced size. From my above comments is should be clear that says they use "B" cams in all their engines they must have purchased a boat load of cams from Bill Stipe or we are back to the apples and oranges syndrome. |
All times are GMT -5. The time now is 07:16 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.