Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-27-2020, 07:11 AM   #1
Jacques1960
Senior Member
 
Jacques1960's Avatar
 
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
Default Wire splicing

Have to replace some of the under dash 6 v wiring; when attaching new (cloth) to old, what is the best means of covering the splice ? I’ve read that friction tape may have been used from time to time on the assembly line, and also note the existence of what appear to be Bakelite splicing “tubes” in a couple of locations. As always, thank you.
Jacques1960 is offline   Reply With Quote
Old 09-27-2020, 07:24 AM   #2
KiWinUS
Senior Member
 
KiWinUS's Avatar
 
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,945
Default Re: Wire splicing

I would suggest “bullet” connectors.
KiWinUS is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-27-2020, 07:29 AM   #3
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: Wire splicing

The best way is to solder splice covered with shrink tubing. If you need to take apart again , the bullet connector would be better.
marko39 is offline   Reply With Quote
Old 09-27-2020, 07:28 AM   #4
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Wire splicing

My first piece of advice is to NOT splice. Rather, replace the harness. If splicing is necessary, it makes me think the harness is old and becoming brittle (not safe).
If you insist on splicing, solder the connections and use heat shrink tubing. Both easy to do and far superior to tape.
Those "tubes" you mention must be hard as a rock for you to see them as Bakelite. They are rubber sleeves over the metal connectors within.
Yes, from your description, I must ask you to please replace the harness. Your car is too nice to chance old, unsafe wiring and connections.
I'd recently purchased harnesses from Mike Driskell. Reasonably priced, shipped quickly and very good quality.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 09-27-2020, 07:48 AM   #5
Jacques1960
Senior Member
 
Jacques1960's Avatar
 
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
Default Re: Wire splicing

Thank you; wasn’t sure of “period correctness” when it comes to wiring. Sounds like safety clearly trumps authenticity in this area. The harness itself appears to have been replaced, with the exception of under dash clock light lead and cigar lighter connections. Rubber sleeves are indeed rock (!) hard at existing butt connection (1) and Y splice (1)
Jacques1960 is offline   Reply With Quote
Old 09-27-2020, 08:57 AM   #6
big job
Senior Member
 
big job's Avatar
 
Join Date: Sep 2013
Location: Dighton, Mass
Posts: 1,225
Default Re: Wire splicing

Sponsored Links (Register now to hide all advertisements)
Another: strip a good 1 inch from each wire the slide shrink wrap over one. Then we
do a "line mans splice" twisting the two into flat then solder then shrink it. twisting flat
means no bulge twisting the ends out with four fingers.
big job is offline   Reply With Quote
Old 09-27-2020, 09:13 AM   #7
Jacques1960
Senior Member
 
Jacques1960's Avatar
 
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
Default Re: Wire splicing

Lineman splice it is - no way that goes anywhere once soldered ����
Jacques1960 is offline   Reply With Quote
Old 09-27-2020, 10:07 AM   #8
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: Wire splicing

Jacques. Take heed to Kube's response. I was repairing the interior courtesy lights in my '46 Coupe, and found a real fire hazard, due to had brittle insulation. The wire runs from the glove box area through the A pillar, over the door opening to the light fixture. I found a number bare spots along the length, and the insulation just crumbled as I handled the wire. As this wire is hot at all times, I'm lucky it never shorted out.
51woodie is offline   Reply With Quote
Old 09-27-2020, 05:52 PM   #9
WBrown
Junior Member
 
WBrown's Avatar
 
Join Date: Sep 2017
Location: Skiatook, Ok
Posts: 26
Default Re: Wire splicing

Quote:
Originally Posted by 51woodie View Post
Jacques. Take heed to Kube's response. I was repairing the interior courtesy lights in my '46 Coupe, and found a real fire hazard, due to had brittle insulation. The wire runs from the glove box area through the A pillar, over the door opening to the light fixture. I found a number bare spots along the length, and the insulation just crumbled as I handled the wire. As this wire is hot at all times, I'm lucky it never shorted out.
Can the courtesy light wire be fished through the A pillar etc? My '47 Fordor has the original headliner and alas the only wire in the harness that hasn't been replaced.
__________________
Aim low--achieve your goals.
WBrown is offline   Reply With Quote
Old 09-27-2020, 07:28 PM   #10
paul2748
Senior Member
 
paul2748's Avatar
 
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,965
Default Re: Wire splicing

Original type bullet connectors are available aftermarket. They used a special FORD size bullet. These are also available aftermarket. They usually come with a plastic cover at the wire connection point, but I removed these, connected the wire to the bare end and then used shrink wrap over it.
__________________
48 Ford Conv
56 Tbird
54 Ford Victoria
paul2748 is offline   Reply With Quote
Old 09-27-2020, 10:07 AM   #11
fourtydlx
Senior Member
 
fourtydlx's Avatar
 
Join Date: May 2010
Location: bloomington,ca 92316
Posts: 784
Send a message via Yahoo to fourtydlx
Default Re: Wire splicing

car is to nice replace that wire
fourtydlx is offline   Reply With Quote
Old 09-27-2020, 10:17 AM   #12
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Wire splicing

You can purchase wire by the foot from RI wiring. Should be able to find a color/tracer pattern to match what you currently have.

http://www.riwire.com/

There is a 10 ft minimum per wire style, but the cost is not that much.

Last edited by JSeery; 09-27-2020 at 10:43 AM.
JSeery is offline   Reply With Quote
Old 09-27-2020, 11:14 AM   #13
Jacques1960
Senior Member
 
Jacques1960's Avatar
 
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
Default Re: Wire splicing

Thank you
Jacques1960 is offline   Reply With Quote
Old 09-28-2020, 06:31 AM   #14
Jacques1960
Senior Member
 
Jacques1960's Avatar
 
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
Default Re: Wire splicing

Has anyone tried the new “solder seal” heat shrink connectors ?
__________________
No job’s done ‘til it’s all done
Jacques1960 is offline   Reply With Quote
Old 09-28-2020, 08:11 AM   #15
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 524
Default Re: Wire splicing

WBrown. If you remove the passenger courtesy light, you can disconnect the wire that comes from the dash/glovebox area. I had my glove box liner removed at the time, so it was easy to access the dash end of the wire. My wire was free to move when I pulled on it, so I connected a strong 6' piece of string to the light end, and pulled the wire out under the dash. I reversed the process to get the new wire in. Just make sure your wire/string splice is "smooth" with no knobs to get caught on anything. I hope this works for you.
Attached Images
File Type: jpg Courtesey Light.jpg (49.5 KB, 29 views)
51woodie is offline   Reply With Quote
Old 09-29-2020, 04:47 PM   #16
WBrown
Junior Member
 
WBrown's Avatar
 
Join Date: Sep 2017
Location: Skiatook, Ok
Posts: 26
Default Re: Wire splicing

Quote:
Originally Posted by 51woodie View Post
WBrown. If you remove the passenger courtesy light, you can disconnect the wire that comes from the dash/glovebox area. I had my glove box liner removed at the time, so it was easy to access the dash end of the wire. My wire was free to move when I pulled on it, so I connected a strong 6' piece of string to the light end, and pulled the wire out under the dash. I reversed the process to get the new wire in. Just make sure your wire/string splice is "smooth" with no knobs to get caught on anything. I hope this works for you.
WOW! THANKS LARGE Nice to be able to preserve the headliner.
__________________
Aim low--achieve your goals.
WBrown is offline   Reply With Quote
Old 10-04-2020, 03:14 AM   #17
Zeke5180
Member
 
Join Date: Feb 2019
Location: Illinois
Posts: 48
Default Re: Wire splicing

If you want to keep the cloth look, Ron Francis sells heat shrink tube with a black cloth otter lining. It looks and works pretty well.
Zeke5180 is offline   Reply With Quote
Old 10-04-2020, 03:15 AM   #18
Zeke5180
Member
 
Join Date: Feb 2019
Location: Illinois
Posts: 48
Default Re: Wire splicing

If you want to keep the cloth look, Ron Francis sells heat shrink tube with a black cloth outer lining. It looks and works pretty well.
Zeke5180 is offline   Reply With Quote
Old 09-28-2020, 08:08 AM   #19
woodiewagon46
Senior Member
 
Join Date: Jun 2012
Location: Long Island,NY
Posts: 1,551
Default Re: Wire splicing

Sometimes soldering two or more wires isn't possible for several reasons. Using the proper crimp butt connector is totally acceptable. The biggest issues with compression splices is using the wrong size compression connector and the wrong crimping tool. Each wire terminal or splice is color coded and specifically designed for each wire size. I have seen 20 gauge wire crimped together with a connector that should have been used for 10 gauge wire. Using a cheap $2.00 crimping tool will only result in a loose and potentially dangerous crimp. Also, if you do use shrink sleeve tubing don't use an open flame torch to shrink the tube, use a heat gun designed for shrink sleeve. If you use the correct fitting and crimping tool you will not have a problem.
woodiewagon46 is offline   Reply With Quote
Old 09-28-2020, 10:18 AM   #20
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: Wire splicing

I've been using un-insulated barrel connectors for the last few years. I started usage on my motorcycles when I started to find failed soldered connections that aged hardened and broke due to vibration. This is normally not the case for our cars but the barrel type are very handy to use without soldering. I cover them with normally two layers of shrink tubing.


The RTL crimper and dies I bought here:


http://www.vintageconnections.com/Products


http://www.vintageconnections.com/Products/Detail/94
glennpm is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:02 AM.