Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-08-2019, 07:19 PM   #1
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Interest in new restoration project thread?

Some of you have expressed interest throughout the past that you'd enjoy a thread wherein I'd show the progress and perhaps some methods to one of my restorations.
I am just beginning a ground up, concourse restoration on a '40 Ford Business coupe.
So, the question is (kind of a poll), "who might enjoy this?"
Mind you, it (the restoration) will take approximately one year.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-08-2019, 07:24 PM   #2
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: Interest in new restoration project thread?

Yes please Mike! I appreciate the workmanship, knowledge and detail you exhibit.
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-08-2019, 07:27 PM   #3
Don W/Norfolk
Senior Member
 
Join Date: May 2010
Location: Norfolk, VA
Posts: 127
Default Re: Interest in new restoration project thread?

Count me in as VERY interested. Thanks for the offer, Mike. dw
__________________
I love this country; it's the damn idiots running the government I'm afraid of.
Don W/Norfolk is offline   Reply With Quote
Old 08-08-2019, 07:31 PM   #4
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Interest in new restoration project thread?

All of your post are interesting and informative, so yes!
JSeery is offline   Reply With Quote
Old 08-08-2019, 07:43 PM   #5
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,711
Default Re: Interest in new restoration project thread?

Can't wait.
Bob C is offline   Reply With Quote
Old 08-08-2019, 07:43 PM   #6
rufus39
Senior Member
 
rufus39's Avatar
 
Join Date: Jun 2012
Location: North Georgia
Posts: 111
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Mike,
Count me in. I always admire your work and level of expertise.
rufus39 is offline   Reply With Quote
Old 08-08-2019, 07:52 PM   #7
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Always dig your posts Kube.
Tinker is offline   Reply With Quote
Old 08-08-2019, 08:00 PM   #8
VeryTangled
Senior Member
 
VeryTangled's Avatar
 
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 3,386
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
"...who might enjoy this?"

Me.
__________________
-Jeff H

Have you thought about supporting the Early Ford V-8 Foundation Museum?
VeryTangled is offline   Reply With Quote
Old 08-08-2019, 08:12 PM   #9
jimalabam
Senior Member
 
jimalabam's Avatar
 
Join Date: May 2010
Location: Lee County Alabama
Posts: 828
Default Re: Interest in new restoration project thread?

Cube: Proceed - I am never to old (82) to learn new information and/or techniques...
jimalabam is offline   Reply With Quote
Old 08-08-2019, 08:37 PM   #10
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Kube, I am interested in following your upcoming restoration also.
Zeke3 is online now   Reply With Quote
Old 08-08-2019, 08:51 PM   #11
estout81
BANNED
 
Join Date: Jun 2010
Location: Utica, Ohio
Posts: 522
Default Re: Interest in new restoration project thread?

Good workmanship always appreciated.
estout81 is offline   Reply With Quote
Old 08-08-2019, 08:57 PM   #12
mhsprecher
Senior Member
 
mhsprecher's Avatar
 
Join Date: Aug 2012
Location: Takoma Park, MD
Posts: 2,811
Default Re: Interest in new restoration project thread?

Yes, indeed.
mhsprecher is offline   Reply With Quote
Old 08-08-2019, 09:05 PM   #13
swoopNZ
MEMBER EMERITUS
 
Join Date: May 2010
Location: New Zealand
Posts: 1,380
Default Re: Interest in new restoration project thread?

Always of interest.
swoopNZ is offline   Reply With Quote
Old 08-08-2019, 09:09 PM   #14
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,541
Default Re: Interest in new restoration project thread?

i'm sure everyone would enjoy seeing the process up to being one of your fine cars. thanks for your offer, and thanks for your time if you choose to go thru with it
cas3 is offline   Reply With Quote
Old 08-08-2019, 09:35 PM   #15
Cool Kat with Hot Car
Senior Member
 
Cool Kat with Hot Car's Avatar
 
Join Date: Jul 2010
Location: NorCal
Posts: 250
Default Re: Interest in new restoration project thread?

looking forward to following your restoration
Cool Kat with Hot Car is offline   Reply With Quote
Old 08-08-2019, 09:47 PM   #16
Mtn Wudy
Senior Member
 
Mtn Wudy's Avatar
 
Join Date: Nov 2012
Location: Montrose,CO
Posts: 224
Default Re: Interest in new restoration project thread?

Count me in .....!!!
Details,,,details........
Can’t Wait.....
__________________
Whether you think that you can,or that you can't,you are usually right....H.Ford
Mtn Wudy is offline   Reply With Quote
Old 08-08-2019, 09:47 PM   #17
TomT/Williamsburg
Senior Member
 
TomT/Williamsburg's Avatar
 
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,646
Default Re: Interest in new restoration project thread?

I would love to follow low along! Thank you!
TomT/Williamsburg is offline   Reply With Quote
Old 08-08-2019, 09:53 PM   #18
Elmo Rodge
Senior Member
 
Elmo Rodge's Avatar
 
Join Date: May 2010
Location: Salina, Utah
Posts: 324
Default Re: Interest in new restoration project thread?

Yes, please.
Wayno
__________________
Life is not a spectator sport.
Elmo Rodge is offline   Reply With Quote
Old 08-08-2019, 09:54 PM   #19
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,


Great idea!
DavidG is offline   Reply With Quote
Old 08-08-2019, 10:12 PM   #20
cmbrucew
Senior Member
 
cmbrucew's Avatar
 
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,063
Default Re: Interest in new restoration project thread?

I will follow it with great interest. Your cars are the picture of perfection.
Thanks for the offer.


Bruce
__________________
Works good
Lasts long time
cmbrucew is offline   Reply With Quote
Old 08-08-2019, 11:03 PM   #21
Ben38
Member
 
Ben38's Avatar
 
Join Date: May 2010
Location: Apple Valley, MN
Posts: 61
Default Re: Interest in new restoration project thread?

I’m very interested too.
Thanks Mike
Ben38 is online now   Reply With Quote
Old 08-08-2019, 11:18 PM   #22
Randy in ca
Senior Member
 
Randy in ca's Avatar
 
Join Date: May 2010
Posts: 1,628
Default Re: Interest in new restoration project thread?

For sure. Build threads always seem to be popular and well viewed and lately there seems to be a noticeable lack of them. Good to share your expertise.
Randy in ca is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-08-2019, 11:27 PM   #23
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: Interest in new restoration project thread?

Me to
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 08-09-2019, 12:55 AM   #24
Karl
Senior Member
 
Karl's Avatar
 
Join Date: May 2010
Location: Manawatu, New Zealand
Posts: 1,416
Default Re: Interest in new restoration project thread?

Me to-Karl
__________________
Such a fine sight to see-Its a Girl, My Lord, in a Flatbed Ford slowin' down to take a look at me.
Karl is offline   Reply With Quote
Old 08-09-2019, 01:08 AM   #25
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

I’ll be watching! For a year it’s going to take one HUGE bowl of popcorn!
But seriously, a year will go by way too fast. I think Lawson has it it right with the toilet paper roll euphemism.
RalphM is offline   Reply With Quote
Old 08-09-2019, 05:12 AM   #26
39portlander
Senior Member
 
39portlander's Avatar
 
Join Date: May 2010
Location: Suth'N Maine
Posts: 1,996
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Another way to also get us motivated with our own projects, there are some of these on various model T's and there great.

Very generous to offer and take the time to do this, should be as good as the write up of your 40 in the V8 times a few issues ago. Scott
39portlander is offline   Reply With Quote
Old 08-09-2019, 05:16 AM   #27
turnpikecrusier
Senior Member
 
Join Date: Jan 2012
Location: Roswell NM
Posts: 162
Default Re: Interest in new restoration project thread?

Yes Yes Yes Please
turnpikecrusier is offline   Reply With Quote
Old 08-09-2019, 05:26 AM   #28
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Mike, that would be fantastic.

If there could be some video content posted to Youtube that would be the icing on the cake. (You know I post videos up).

Mart.
Mart is offline   Reply With Quote
Old 08-09-2019, 05:39 AM   #29
40ford
Senior Member
 
40ford's Avatar
 
Join Date: May 2010
Location: Cherryville,N.C.
Posts: 535
Default Re: Interest in new restoration project thread?

Yes indeed Kube.You have helped me alot over the years.Russ
40ford is offline   Reply With Quote
Old 08-09-2019, 05:41 AM   #30
JRA66
Junior Member
 
Join Date: Sep 2017
Posts: 1
Default Re: Interest in new restoration project thread?

Would be of great interest.


Jim
JRA66 is offline   Reply With Quote
Old 08-09-2019, 05:49 AM   #31
dwaynec
Senior Member
 
dwaynec's Avatar
 
Join Date: Jan 2014
Location: Davenport, IA
Posts: 169
Default Re: Interest in new restoration project thread?

Me too.
__________________
Dwayne
dwaynec is offline   Reply With Quote
Old 08-09-2019, 06:01 AM   #32
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: Interest in new restoration project thread?

I'm in !!
Charlie ny
Charlie ny is offline   Reply With Quote
Old 08-09-2019, 06:48 AM   #33
KiWinUS
Senior Member
 
KiWinUS's Avatar
 
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,945
Default Re: Interest in new restoration project thread?

I’m in
KiWinUS is offline   Reply With Quote
Old 08-09-2019, 06:55 AM   #34
Shoebox
Senior Member
 
Shoebox's Avatar
 
Join Date: Jan 2014
Location: Holmen,Wisconsin
Posts: 772
Default Re: Interest in new restoration project thread?

Let's go!!
__________________
I went, I saw, I bought the T shirt

51 Ford Deluxe Tudor
32 Ford roadster
39 Mercury Towncar
Shoebox is offline   Reply With Quote
Old 08-09-2019, 07:20 AM   #35
Angledrive
Senior Member
 
Angledrive's Avatar
 
Join Date: May 2010
Location: Lakeland Florida
Posts: 302
Default Re: Interest in new restoration project thread?

Count me also
Angledrive is offline   Reply With Quote
Old 08-09-2019, 07:20 AM   #36
deuce5wndw
Senior Member
 
deuce5wndw's Avatar
 
Join Date: May 2010
Location: Liberty, KY
Posts: 896
Default Re: Interest in new restoration project thread?

Me too!
deuce5wndw is offline   Reply With Quote
Old 08-09-2019, 08:22 AM   #37
Planojc
Senior Member
 
Planojc's Avatar
 
Join Date: May 2010
Location: Plano, Texas
Posts: 829
Default Re: Interest in new restoration project thread?

yes for sure.
Planojc is online now   Reply With Quote
Old 08-09-2019, 08:23 AM   #38
Gary in La.
Senior Member
 
Gary in La.'s Avatar
 
Join Date: May 2010
Location: Louisiana
Posts: 866
Default Re: Interest in new restoration project thread?

What are you waiting for? Lets get this project moving!
Gary in La. is offline   Reply With Quote
Old 08-09-2019, 09:13 AM   #39
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Since I am finishing up my 40 V8 business coupe, I would be very interested to see what I could have done better! Of course I would love to follow your restoration!
deuce_roadster is offline   Reply With Quote
Old 08-09-2019, 09:22 AM   #40
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Count me in OR as one on the list!!!
rockfla is online now   Reply With Quote
Old 08-09-2019, 09:25 AM   #41
wamnram
Senior Member
 
wamnram's Avatar
 
Join Date: May 2010
Location: San Tan Valley, Arizona
Posts: 210
Default Re: Interest in new restoration project thread?

Awesome Kube, I'm just getting started on my 36 Cabriolet so I could definitely use some pointers!
Attached Images
File Type: jpg IMG_0182.jpg (91.8 KB, 125 views)
__________________
Wayne
wamnram is offline   Reply With Quote
Old 08-09-2019, 09:25 AM   #42
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by deuce_roadster View Post
Since I am finishing up my 40 V8 business coupe, I would be very interested to see what I could have done better! Of course I would love to follow your restoration!
I can't match your workmanship. No how, no way.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-09-2019, 09:27 AM   #43
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Okay guys... THANKS for all of the (too) kind messages.
I'll start the thread ASAP. I have no doubt a lot of it will be akin to watching paint dry. The "fun' part to me is when stuff starts going back together. That'll be quite a while.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-09-2019, 09:27 AM   #44
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Interest in new restoration project thread?

Sounds like a great idea to me.
TJ is offline   Reply With Quote
Old 08-09-2019, 09:28 AM   #45
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by wamnram View Post
Awesome Kube, I'm just getting started on my 36 Cabriolet so I could definitely use some pointers!
Wow! That looks like a great car to start with. Is it as solid as it appears? Fairly complete? Are you planning a concourse type restoration?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-09-2019, 10:25 AM   #46
wamnram
Senior Member
 
wamnram's Avatar
 
Join Date: May 2010
Location: San Tan Valley, Arizona
Posts: 210
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Kube View Post
Wow! That looks like a great car to start with. Is it as solid as it appears? Fairly complete? Are you planning a concourse type restoration?
Kube, Yes, its complete, even has matching serial on frame and tranny. I will restore to like original as best I can. My skills allow me to achieve what I call an "amateur' restoration. May try to do better with this one though.
__________________
Wayne
wamnram is offline   Reply With Quote
Old 08-09-2019, 10:57 AM   #47
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,421
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Some of you have expressed interest throughout the past that you'd enjoy a thread wherein I'd show the progress and perhaps some methods to one of my restorations.
I am just beginning a ground up, concourse restoration on a '40 Ford Business coupe.
So, the question is (kind of a poll), "who might enjoy this?"
Mind you, it (the restoration) will take approximately one year.
Any chance you could document it with a GoPro? Easy to use, edit and post. If you don't have one, the early ones, 3 Hero, are cheap enough on e-bay.

https://www.ebay.com/sch/i.html?_odk...3&_sacat=10073
Merc Cruzer is offline   Reply With Quote
Old 08-09-2019, 11:23 AM   #48
Hal Beatty
Senior Member
 
Hal Beatty's Avatar
 
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
Default Re: Interest in new restoration project thread?

Yes, very interested!
Hal Beatty is offline   Reply With Quote
Old 08-09-2019, 12:08 PM   #49
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: Interest in new restoration project thread?

Yes please, the 40 is one of my favorite cars. Hi Wayno great hearing from you, take care.
Ol' Ron is online now   Reply With Quote
Old 08-09-2019, 12:28 PM   #50
A bones
Senior Member
 
A bones's Avatar
 
Join Date: May 2010
Location: CLAYTON DE
Posts: 1,280
Default Re: Interest in new restoration project thread?

Both hands up. Both eyes and ears open.
__________________
Enjoy yer day. Tom
Hate can't fix what it started.
A bones is offline   Reply With Quote
Old 08-09-2019, 12:54 PM   #51
Bob NH
Senior Member
 
Bob NH's Avatar
 
Join Date: May 2010
Location: Meredith, N.H.
Posts: 766
Default Re: Interest in new restoration project thread?

YES Mike, let's light this candle !
Bob NH is offline   Reply With Quote
Old 08-09-2019, 01:26 PM   #52
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

I am in. Thanks, Mike.

You could actually make this into a book showing what's entailed in each part of a restoration.

Such as: exterior, frame and chassis, drive train, interior, wiring, glass, suppliers, etc.

Last edited by 19Fordy; 08-09-2019 at 02:17 PM.
19Fordy is offline   Reply With Quote
Old 08-09-2019, 01:54 PM   #53
Terranova
Senior Member
 
Join Date: May 2012
Location: Grove City, Oh
Posts: 255
Default Re: Interest in new restoration project thread?

Oh yes. Excited
Terranova is offline   Reply With Quote
Old 08-09-2019, 02:06 PM   #54
Ford46
Senior Member
 
Ford46's Avatar
 
Join Date: May 2010
Location: Southeastern, MA
Posts: 433
Default Re: Interest in new restoration project thread?

Looking forward to it!
Ford46 is offline   Reply With Quote
Old 08-09-2019, 02:14 PM   #55
Ricosan
Senior Member
 
Ricosan's Avatar
 
Join Date: May 2018
Location: Tallahassee
Posts: 375
Default Re: Interest in new restoration project thread?

I’m in!
Ricosan is offline   Reply With Quote
Old 08-09-2019, 04:40 PM   #56
B-O-B
Senior Member
 
B-O-B's Avatar
 
Join Date: May 2010
Location: Ft Mohave,Az
Posts: 1,984
Default Re: Interest in new restoration project thread?

Move over there bud I need a seat for this one. I'm in, Take your time.
B-O-B is offline   Reply With Quote
Old 08-09-2019, 06:05 PM   #57
Bill E Bob
Junior Member
 
Join Date: Feb 2018
Location: Skiatook, Ok
Posts: 8
Default Re: Interest in new restoration project thread?

Let's see some of your elegant engineering.
__________________
Aim low--Achieve your goals!
Bill E Bob is offline   Reply With Quote
Old 08-09-2019, 06:50 PM   #58
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
I can't match your workmanship. No how, no way.
Uh, Mike, I think it is the other way around! But thanks!
deuce_roadster is offline   Reply With Quote
Old 08-09-2019, 07:11 PM   #59
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

double post, my error.
deuce_roadster is offline   Reply With Quote
Old 08-09-2019, 09:19 PM   #60
flatjack9
Senior Member
 
flatjack9's Avatar
 
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,516
Default Re: Interest in new restoration project thread?

Count me in.
flatjack9 is offline   Reply With Quote
Old 08-09-2019, 09:54 PM   #61
zoegrant
Senior Member
 
zoegrant's Avatar
 
Join Date: Jun 2010
Location: tolland CT
Posts: 773
Default Re: Interest in new restoration project thread?

definitely count me in....
zoegrant is offline   Reply With Quote
Old 08-09-2019, 10:00 PM   #62
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Interest in new restoration project thread?

Nah, not interested.

Just kidding, I just don't want your head to get too big. Let's get on with it!
tubman is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-10-2019, 04:47 AM   #63
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Of course it's easy for us to say. it's no effort at all on our part but lots of work on Mikes part. Taking pictures, writing the text, getting the images cropped and edited, getting them uploaded (Not great on the barn). PhotoBucket used to be ideal but not any more.
It's a lot of work. I know. I've done it.

But Mike, we would all appreciate any progress reports you can make for us. maybe a weekly update? Week 1, week 2 etc.?

Thanks for at least thinking about doing it.

Mart.
Mart is offline   Reply With Quote
Old 08-10-2019, 06:26 AM   #64
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: Interest in new restoration project thread?

Yes, sir.
rich b is offline   Reply With Quote
Old 08-11-2019, 06:41 AM   #65
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: Interest in new restoration project thread?

My hand is raised..... meaning "heck yeah"!!
We can always learn from others, IF we have a mind too.
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Old 08-11-2019, 10:40 AM   #66
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
My '40 could use some freshening up. Go ahead and motivate me.....
Russ/40 is offline   Reply With Quote
Old 11-04-2019, 07:25 PM   #67
40ford
Senior Member
 
40ford's Avatar
 
Join Date: May 2010
Location: Cherryville,N.C.
Posts: 535
Default Re: Interest in new restoration project thread?

Kube,are you still considering the restoration thread on a 40?
40ford is offline   Reply With Quote
Old 11-06-2019, 02:48 PM   #68
'36 5W
Senior Member
 
'36 5W's Avatar
 
Join Date: Aug 2010
Location: Vancouver, Wa.
Posts: 193
Default Re: Interest in new restoration project thread?

Ditto here; subscribed!
'36 5W is offline   Reply With Quote
Old 11-07-2019, 04:05 AM   #69
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

I'm interested for sure.
RobR'35 is offline   Reply With Quote
Old 11-07-2019, 11:14 AM   #70
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: Interest in new restoration project thread?

Mike,
By all means step back into it. Your convertible restoration was a classic.....the
'issue' where you described fitting the trunk lid encouraged my buddy with a 40 coupe to
pie cut his lid as you did , to get it to lay down right and lock up with a clunk. I'm
hoping to get a piece of whatever is on your to do list.
Charlie ny
Charlie ny is offline   Reply With Quote
Old 11-07-2019, 11:17 AM   #71
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,844
Default Re: Interest in new restoration project thread?

Like so many others, I look forward to this thread!
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is online now   Reply With Quote
Old 11-07-2019, 11:19 PM   #72
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Geez... I opened this thread hoping to see a project. But no!


Get to it Mike "Mr. Kube" posting! we love your work!


Hope all is well!


.
Tinker is offline   Reply With Quote
Old 11-08-2019, 04:59 AM   #73
48-710
Senior Member
 
Join Date: May 2010
Location: Mildura ,Australia
Posts: 163
Default Re: Interest in new restoration project thread?

I'm also in. Lights,action,camera.
48-710 is offline   Reply With Quote
Old 11-08-2019, 06:05 AM   #74
turnpikecrusier
Senior Member
 
Join Date: Jan 2012
Location: Roswell NM
Posts: 162
Default Re: Interest in new restoration project thread?

I'll be following this with great interest, especially the hood installation.
turnpikecrusier is offline   Reply With Quote
Old 11-08-2019, 08:49 AM   #75
sidevalve8ba
Senior Member
 
sidevalve8ba's Avatar
 
Join Date: May 2013
Location: Harrisonburg, VA
Posts: 841
Default Re: Interest in new restoration project thread?

Count me in!
sidevalve8ba is offline   Reply With Quote
Old 11-08-2019, 10:05 AM   #76
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Good morning gentleman.

Life is finally settling back down in to my normal. My normal equates to working 18+ hours a day and loving it. Businesses, horses (eleven of them) writing my book and well, life, kinda gets in the way of restoration threads.
I'll start this thread with the hopeful understanding that these restorations are a hobby / passion for me. It takes me about twelve to fourteen months to complete a full restoration.
It can fairly be argued that there as many approaches to a restoration as there are projects. My approach is just one and there's little doubt not the best one by far. I continue to learn day after day and on occasion wonder how and why "I didn't think of that" much earlier in life.
Anyway, feel free to express advice, raise queries, heck, (positive) criticize.

As a bit of overlook, I tend to inspect the vehicle closely and take many photos prior to disassembly. As many of these as I've done, I forget stuff. Oh, this is #17 - all were either '39 or '40 Fords with the exception of two Buicks, a '31 and a '38 (sorry guys).
I then disassemble the car down to the very last nut and bolt. I don't tend to label and bag as much as I used to as I for the most part know exactly "what bolt goes where".

The next step is to take a written inventory of any and all parts I feel I may need for the completion of the project. I use as few reproduction parts as possible but some (repop) parts I find necessary and / or prudent to utilize.
I promptly seek and purchase all pieces I think I may need. I don't care to be held up simply because I can't locate a certain required piece on any day.

I do tend to work on a number of assemblies simultaneously. Why? Well, I tend to get "burned out" if I spend countless hours / days working on (example) on fender.
I tend to complete the chassis first as heck, it's the foundation of all to come afterward.

While finishing the frame, I will also finish each subassembly. As an example, the brake backing plates will be fully restored and assembled. Another example? The brake / clutch pedal assembly will be fully restored. All of these subassemblies will have their respective fasteners placed with them in storage. And yes, I keep a very accurate inventory of what part is in what box and on what shelf.
I believe you can picture how a chassis comes together easily for me. It so much fun (yeah, a sickness) to be able to work hours upon hours assembling the chassis with no interruptions as all the required pieces are finished, in a box, awaiting installation. Another benefit of this approach is when the chassis is assembled, it is all very fresh and pristine at the same moment.
Okay, thanks for putting up with me thus far.
Oh, I am 100% certain my restorations are not for everyone. They are without argument "over restored". However, only in the fit and finish are they over restored.
Correct? I will discuss with anyone - anything, that they may feel is incorrect. Like I'd mentioned earlier, I continue to learn.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 10:09 AM   #77
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Here's a couple of phots of the car I'd received. Upon initial inspection, it appeared to be beautiful. Isn't that often the case upon initial inspections?
Attached Images
File Type: jpg left 14 b4.jpg (46.4 KB, 287 views)
File Type: jpg interior front b4 (1).jpg (62.4 KB, 278 views)
File Type: jpg headliner rear b4.jpg (54.8 KB, 262 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 10:17 AM   #78
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Then I disassemble the entire car. Many of the small pieces get media blasted ASAP. Some will get powder finished, many more will be painted.
The body, fenders, doors, etc. get sent out for plastic media blasting. Why?
Plastic will not warp any sheet metal surface and unlike acid dipping, it will not come back to haunt you years later.
Also, unlike acid dipping, heavy rust will not be removed with plastic beads. This is of no concern to me as I repair / replace and compromised sheet metal.
The frame will get sand blasted - quite aggressively.
Attached Images
File Type: jpg 8-1-19 2.jpg (65.8 KB, 224 views)
File Type: jpg 8-1-19.jpg (43.0 KB, 224 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 10:28 AM   #79
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Thanks for posting the start of your new restoration.It will be a great documentation for the owner as well as other interested folks. The time and effort you take to do this is much appreciated. Be sure and take photos of "the small stuff" as that's often taken for granted as stuff folks already know. Will be following you. Love the way you lay the parts out so neatly for photos. I hope you will be able to feature this as part of your book. It would be a wonderful eye-opener. Thanks. Jim
19Fordy is offline   Reply With Quote
Old 11-08-2019, 10:29 AM   #80
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

As I'd said earlier, there always are "surprises" not seen upon initial inspection. This car was no different than any previously restored.
While the body shell, doors, hood, etc. are as beautiful as I'd thought, the floor, well, not so much.
I can't quite grasp what happened to necessitate the repair but I can tell you it was done poorly at best. My guess is it was done decades ago when a coupe like this had very little value.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 10:34 AM   #81
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I tend to be very methodical during the process of restoration. That method seemingly keeps me from having to do things twice.
I measure, then measure again, and again - whatever is necessary. I trial fit all parts before any finish is applied.
All of the factory welds are removed and will be replaced when appropriate.
I am using a reproduction tail pan as well as the rear most trunk floor. Both pieces are "okay" as delivered. Okay at best. Both took quite a bit of massaging to get to fit properly.
The center floor pan is not available as reproduction and even though this one was beat up, it will be beautiful once reinstalled.
Note the tool tray was very solid. Most of the authentic tar paper lining remained intact.
This car was hit from behind at some point in its life. What I am unable to determine is why the floor was damaged as it was. the rear quarters have zero damage and zero repairs. The tail pan and rear most trunk floor were both damaged fairly bad.
I gut tells me two distinct causes. Tail pan? Simple rear end type accident. Floor? Perhaps something very heavy was tossed in there? hey, it happens. I'd restored a '40 coupe about six years ago that was 100% rust and dent free. Beautiful car to start with. Trunk floor was dented so badly, sheet metal stretched... turns out the previous owner threw an engine block in the trunk!
Attached Images
File Type: jpg P1050313.JPG (147.5 KB, 363 views)
File Type: jpg P1050315.JPG (143.5 KB, 362 views)
File Type: jpg P1050316.JPG (151.0 KB, 349 views)
File Type: jpg trunk b4.jpg (77.0 KB, 347 views)
__________________
"I can explain it for you. However, I can't understand it for you".

Last edited by Kube; 11-08-2019 at 10:41 AM.
Kube is offline   Reply With Quote
Old 11-08-2019, 10:51 AM   #82
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
Thanks for posting the start of your new restoration.It will be a great documentation for the owner as well as other interested folks. The time and effort you take to do this is much appreciated. Be sure and take photos of "the small stuff" as that's often taken for granted as stuff folks already know. Will be following you. Love the way you lay the parts out so neatly for photos. I hope you will be able to feature this as part of your book. It would be a wonderful eye-opener. Thanks. Jim
Jim, The book will have zero in regard to restoration processes. My gosh man, it's been years of research to get this far on that (book) project. I can't imagine how much more time would be required to do a restoration phase. That sounds like a different book entirely. For someone else to do.
I do photograph most assemblies "before" and "after". I place them in a photo album side by side in an order leading up to the final end result.
I figure these will be my "coloring books" for when I am able to do little more than look at them and (hopefully) recall them
The horns depicted in the accompanying photos are from a '39 wagon I'd restored. The steering column from a '40 coupe.
If the cars are sold, a hard copy of the album is always included with the sale.
Attached Images
File Type: jpg horns before.jpg (50.3 KB, 204 views)
File Type: jpg horns after.jpg (70.0 KB, 208 views)
File Type: jpg column lock b4.jpg (45.7 KB, 211 views)
File Type: jpg column lock aft.jpg (33.7 KB, 224 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-08-2019, 10:52 AM   #83
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Wow. Thanks for posting the story so far mike. This is an excellent subject. While your and my approaches to restoration are at polar opposites, I really appreciate the way you do what you do.

Mart.
Mart is offline   Reply With Quote
Old 11-08-2019, 10:55 AM   #84
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Mart View Post
Wow. Thanks for posting the story so far mike. This is an excellent subject. While your and my approaches to restoration are at polar opposites, I really appreciate the way you do what you do.

Mart.
What is your approach Mart?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 10:59 AM   #85
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Leave it alone as much as possible and just take care of any mechanical/safety issues. As I said in a previous post talking about over restoration: I said "I tend to under restore my heaps". Lol.
Mart is offline   Reply With Quote
Old 11-08-2019, 11:02 AM   #86
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Mart View Post
Leave it alone as much as possible and just take care of any mechanical/safety issues. As I said in a previous post talking about over restoration: I said "I tend to under restore my heaps". Lol.
You're funny! And probably a lot more (mentally) healthy
Me? I can't leave any of them alone. Every one must be perfect! No doubt, it's a bit of a sickness. I'm okay with that!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2019, 11:05 AM   #87
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Mike, since you have already done many of these, you probably already have enough pictures for you to assemble a "restoration" book of your own for sale. All you would need to do is minimal text for your steps and of course the sequence. No need to go into detail how to shrink metal, weld, wet sand, paint etc. Would be easy after you have decided you have restored enough cars.
Thanks for sharing your procedures as they can be relevant to any restoration, even brand X!
deuce_roadster is offline   Reply With Quote
Old 11-10-2019, 09:02 AM   #88
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I am currently preparing the frame for paint. Although a super nice frame - very straight and only a few pits, it did have the typical damage to a middle cross member.
I do repair all dings, waves, pits, etc. Then prime, wet sand and shoot single stage gloss black.
Attached Images
File Type: jpg P1050201.JPG (145.0 KB, 305 views)
File Type: jpg P1050335.JPG (141.0 KB, 284 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-10-2019, 11:18 AM   #89
Don Rogers
Senior Member
 
Don Rogers's Avatar
 
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
Default Re: Interest in new restoration project thread?

Mike, I'm glad that you are making a distinction between a "how to restore" book and a "how did Henry make them" book. There are a lot of "how to restore" books and few "what was correct" books. Your efforts on behalf of a "factory correct" 1940 Ford are certainly appreciated. Once again, if you need any help putting the book together, let me know.
Don Rogers is offline   Reply With Quote
Old 11-10-2019, 11:32 AM   #90
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Don Rogers View Post
Mike, I'm glad that you are making a distinction between a "how to restore" book and a "how did Henry make them" book. There are a lot of "how to restore" books and few "what was correct" books. Your efforts on behalf of a "factory correct" 1940 Ford are certainly appreciated. Once again, if you need any help putting the book together, let me know.
Don, I very much appreciate your kind offer. Lord knows you've earned my respect!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-10-2019, 01:29 PM   #91
40ford
Senior Member
 
40ford's Avatar
 
Join Date: May 2010
Location: Cherryville,N.C.
Posts: 535
Default Re: Interest in new restoration project thread?

Kube,that looks almost like a dual exhaust cut-out some time long ago!I know my 40 had duals on it some time or another and the drivers side has been motified for exhaust.
40ford is offline   Reply With Quote
Old 11-10-2019, 02:09 PM   #92
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: Interest in new restoration project thread?

Go for it, one of my favorite cars. I did a repaint in Black laquer, some new glass 37 DeSota bumpers etc. Nice car, sold it for 600 bucks, Raising a family, added another mouth.
Ol' Ron is online now   Reply With Quote
Old 11-10-2019, 02:13 PM   #93
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 40ford View Post
Kube,that looks almost like a dual exhaust cut-out some time long ago!I know my 40 had duals on it some time or another and the drivers side has been motified for exhaust.
If I recall correctly, nearly every 39 - 40 I have ever restored has had damage to that brace.
I always figured it was some "backyard hack" to install a replacement exhaust. You know... why do it right when it's so much easier to hack out a chunk of the brace?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-10-2019, 02:31 PM   #94
mhsprecher
Senior Member
 
mhsprecher's Avatar
 
Join Date: Aug 2012
Location: Takoma Park, MD
Posts: 2,811
Default Re: Interest in new restoration project thread?

Thanks for taking the time to do a thread. A lot of work is involved in putting one together. It is like writing a book, but with very short chapters.
__________________
1924 Model T Coupe
1928 Model A Roadster
1930 Model A Town Sedan
1939 Deluxe Fordor
1945 pickup
1951 Custom convertible
mhsprecher is offline   Reply With Quote
Old 11-11-2019, 02:11 AM   #95
Karl
Senior Member
 
Karl's Avatar
 
Join Date: May 2010
Location: Manawatu, New Zealand
Posts: 1,416
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
You're funny! And probably a lot more (mentally) healthy
Me? I can't leave any of them alone. Every one must be perfect! No doubt, it's a bit of a sickness. I'm okay with that!
You guys Stateside are so lucky compared with Mart and I . You have a lot more access to correct parts than we do. In my case 12000 miles of shipping really whacks up the restoration costs. I have spend a lot of money making my cars look right but a fine points guy would spot many things wrong with all of them. For example on my Model A the generator looks correct but is 6 months younger than my car-Getting the correct generator out of the States is feasible but not economically viable when only one person in 10,000 here would identify it as correct.

The distance means that our cars often don't follow the accepted time lines any way. My 1934 Fordor was registered in New Zealand In April 1934 but was probably assembled Stateside in Jan 1934 It has a combination of 33 and 34 Parts on it from new.

Due to our isolation and hence cost of new parts our cars have often been kept going with Farmers fixes over the years rather than expensive genuine parts . This again complicates restoration.

For the above reasons Fine point judging doesn't really exist over here. I wish it did -but then I'd be to scared to drive them

In short do you need any aging car mad Doctors in the States LOL !
__________________
Such a fine sight to see-Its a Girl, My Lord, in a Flatbed Ford slowin' down to take a look at me.
Karl is offline   Reply With Quote
Old 11-11-2019, 07:30 AM   #96
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

[QUOTE=Karl;1820079]You guys Stateside are so lucky compared with Mart and I . You have a lot more access to correct parts than we do. In my case 12000 miles of shipping really whacks up the restoration costs. I have spend a lot of money making my cars look right but a fine points guy would spot many things wrong with all of them. For example on my Model A the generator looks correct but is 6 months younger than my car-Getting the correct generator out of the States is feasible but not economically viable when only one person in 10,000 here would identify it as correct.


Karl, I have often admired you guys from across the great pond. I've shipped a lot of parts in your direction and as you'd stated, the shipping costs are insane.
I hope you are able to continue enjoying your hobby.
__________________
"I can explain it for you. However, I can't understand it for you".

Last edited by Kube; 11-11-2019 at 08:58 AM.
Kube is offline   Reply With Quote
Old 11-11-2019, 08:50 AM   #97
funrunr
Senior Member
 
funrunr's Avatar
 
Join Date: May 2010
Location: Belleville,MI
Posts: 1,426
Default Re: Interest in new restoration project thread?

Kube, Do you do all the restoration yourself? Example being for instance; the horns, generators and windings, rebuilding the clocks and parts like that? Where do you draw the line?
Once again, thanks for bringing us along.
Mark
__________________
Thank God
this is only a hobby!
funrunr is online now   Reply With Quote
Old 11-11-2019, 08:58 AM   #98
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by funrunr View Post
Kube, Do you do all the restoration yourself? Example being for instance; the horns, generators and windings, rebuilding the clocks and parts like that? Where do you draw the line?
Once again, thanks for bringing us along.
Mark
Good morning Mark.

I do most of the work. However, some things are simply out of my hands.
Plating and most machining come to mind.

I used to be able to do the engine machining when employed as a tool maker. Unfortunately, after I'd retired, I'd lost access to the necessary machines.
Clocks you ask? More often than not, they simply need to be cleaned and lightly oiled.
I do rebuild the horns myself as well as generators, starters, transmissions, differentials, etc.
I now send my distributors, some fuel pumps and carburetors out to Charlie Schwendler. I used to do my own but find the minimal cost (of Charlie's work) along with the high quality, well, I just figure it is no longer worth my time / efforts to do them any longer.
I don't mount my tires or cut my own glass.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-11-2019, 01:47 PM   #99
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

No doubt, Kubarth ("Kube") surely has restored an appreciable number of '39s and '40s over the last several years. I really don't understand how he is able to complete each in the seemingly-short time that he usually spends completing one. Of all the cars Mike has done over the years and has had judged, I've only managed to scrutinize two of his earlier restorations...the little blue coupe that shows in his avatar, and that now-infamous blue '40 Convert (with accompanying drink holder) that eventually ended-up selling out of the Dingman Collection for a reported $165K several years back. I remember Mike saying that that car judged ONLY 999 points, and that because of a 1-point deduction for two tiny pits in one of the rear axle housings. I honestly believe that the blue avatar coupe must surely be one of his favorites as Mike sold that coupe to someone in the northeast I believe, only to re-purchase it at a later date. I understand that he eventually sold it a second time, and have since heard that he would really like to have it back AGAIN. Almost kind of comical! But my whole point here is to express my thoughts about the extent of the detail and workmanship that Mike puts into these jewels by bringing attention to a couple of oft-overlooked and frequently forgotten areas for restoration. On the two "Kubarth" '40s that I'm familiar with above, you could look down past the roll-up windows in the doors and notice the result of what must have been some painstaking effort to make the insides and bottoms of those doors look just as pristine and finished as the paint on the fenders. Not only were the door innards a work of art, but the underside and rear of the instrument panel area along with the upper, inside of the dash (firewall) were finished every bit as nicely as any other part of the interior that shows in plain view. The guy seems to have this 1940 Ford restoration process about down to a science. I think that Mike really must be, by his own admission, one of those seriously-afflicted OCD types, as he seems to be the consummate artisan, always paying the utmost of attention to the minute details that make any "Kubarth Restoration" a significant work of note. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 11-11-2019, 02:34 PM   #100
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Interest in new restoration project thread?

What a wonderful opportunity! For rookies, like myself, describe, for example, the frame process....






media blasting, filing , sanding, paint.....






Maybe I'm getting ahead of you. When I saw those horns, I was curious as to the steps of making them look so nice.






Thank you for your time, it's one thing to do a restore, it's another to take time and post about it all along the way...
Flathead Youngin' is offline   Reply With Quote
Old 11-11-2019, 04:14 PM   #101
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
No doubt, Kubarth ("Kube") surely has restored an appreciable number of '39s and '40s over the last several years. I really don't understand how he is able to complete each in the seemingly-short time that he usually spends completing one. Of all the cars Mike has done over the years and has had judged, I've only managed to scrutinize two of his earlier restorations...the little blue coupe that shows in his avatar, and that now-infamous blue '40 Convert (with accompanying drink holder) that eventually ended-up selling out of the Dingman Collection for a reported $165K several years back. I remember Mike saying that that car judged ONLY 999 points, and that because of a 1-point deduction for two tiny pits in one of the rear axle housings. I honestly believe that the blue avatar coupe must surely be one of his favorites as Mike sold that coupe to someone in the northeast I believe, only to re-purchase it at a later date. I understand that he eventually sold it a second time, and have since heard that he would really like to have it back AGAIN. Almost kind of comical! But my whole point here is to express my thoughts about the extent of the detail and workmanship that Mike puts into these jewels by bringing attention to a couple of oft-overlooked and frequently forgotten areas for restoration. On the two "Kubarth" '40s that I'm familiar with above, you could look down past the roll-up windows in the doors and notice the result of what must have been some painstaking effort to make the insides and bottoms of those doors look just as pristine and finished as the paint on the fenders. Not only were the door innards a work of art, but the underside and rear of the instrument panel area along with the upper, inside of the dash (firewall) were finished every bit as nicely as any other part of the interior that shows in plain view. The guy seems to have this 1940 Ford restoration process about down to a science. I think that Mike really must be, by his own admission, one of those seriously-afflicted OCD types, as he seems to be the consummate artisan, always paying the utmost of attention to the minute details that make any "Kubarth Restoration" a significant work of note. DD
Yep, just a tad OCD.
Your words are too kind and undeserved.
Thank you. I appreciate your comments.

I'm blushing
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2019, 10:46 AM   #102
Planojc
Senior Member
 
Planojc's Avatar
 
Join Date: May 2010
Location: Plano, Texas
Posts: 829
Default Re: Interest in new restoration project thread?

Looking forward to seeing what you do on your lunch hour.
Planojc is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-13-2019, 05:27 PM   #103
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Flathead Youngin' View Post
What a wonderful opportunity! For rookies, like myself, describe, for example, the frame process....media blasting, filing , sanding, paint.....
Thank you for your time, it's one thing to do a restore, it's another to take time and post about it all along the way...
Tomorrow is (gloss black) paint time on the frame. I am eager.

You'd asked about the process in regard to the frame...
I start by removing all components from it. Then I clean away all the grease, etc. Then it's sand blasted quite aggressively.
Once I am certain the frame is true, I begin to repair any bends, dings, etc. If there are "extra" holes that don't belong in a restored frame, those get welded shut and metal finished smooth.
This frame required one of the middle cross braces to be replaced. The replacement was riveted in as was authentic.
Then I prime and sand. I prepare my frames as I prepare hoods, fenders, etc. As most realize, the proper preparation is paramount to a beautiful finished result.
Then, I prime and sand again.
This was a rather nice frame to begin with. Very few pits and other than that damaged brace, little other repair work was required.

Tomorrow I will wipe this down with Pre-Cleano one more time and shoot...
Attached Images
File Type: jpg P1050340.JPG (156.0 KB, 200 views)
File Type: jpg P1050341.JPG (155.0 KB, 199 views)
File Type: jpg P1050342.JPG (153.0 KB, 190 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2019, 07:53 PM   #104
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,


A detour, but I wanted you to know that you are not alone.
Attached Images
File Type: jpg 20190416_170146.jpg (51.4 KB, 219 views)
DavidG is offline   Reply With Quote
Old 11-13-2019, 08:29 PM   #105
Willi_D
Junior Member
 
Willi_D's Avatar
 
Join Date: Mar 2014
Location: N. Illinois
Posts: 12
Default Re: Interest in new restoration project thread?

Nice ..wish I had more free Time & Garage space to work on mine..
Willi_D is offline   Reply With Quote
Old 11-13-2019, 08:35 PM   #106
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by DavidG View Post
Mike,


A detour, but I wanted you to know that you are not alone.
Wow! I'd like to think great minds think alike but there is only one great mind at work here - yours.
So, I'll chalk this up to coincidence. Very cool Dave. Thanks for sharing!

What's your frame going to end up under?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2019, 08:46 PM   #107
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Interest in new restoration project thread?

Mike, Nice work! those frames sure are a pain to sand all the little crevices to remove the pitting, as you know. Assembly seems to be the easy part on a Early Ford V-8, but the sanding, blocking and paint related tasks are where he work really is in my opinion.

On a side note, what brand primer do you use? Also what about paint?

If you have never checked out Tamco Paint, I would recommend it highly as it seems to out surpass the PPG counterparts. I would bet most everything I own that that beautiful frame David posted a photo of was done with Tamco Products.

Hat's off to you, and excellent work!
35fordtn is offline   Reply With Quote
Old 11-13-2019, 09:24 PM   #108
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,

Under these things, but there is a fundamental difference in that what you show is your handiwork and in my photos, the handiwork is that of a couple of long-time good friends who happen to be world-class painters and paint preparers. My role is researcher, parts finder, and final assembler where the devil in the details.
Attached Images
File Type: jpg 20181122_135448-1.jpg (41.9 KB, 164 views)
File Type: jpg 20190419_143907-1.jpg (41.3 KB, 165 views)

Last edited by DavidG; 11-13-2019 at 09:31 PM.
DavidG is offline   Reply With Quote
Old 11-13-2019, 09:30 PM   #109
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 35fordtn View Post
Mike, Nice work! those frames sure are a pain to sand all the little crevices to remove the pitting, as you know. Assembly seems to be the easy part on a Early Ford V-8, but the sanding, blocking and paint related tasks are where he work really is in my opinion.

On a side note, what brand primer do you use? Also what about paint?

If you have never checked out Tamco Paint, I would recommend it highly as it seems to out surpass the PPG counterparts. I would bet most everything I own that that beautiful frame David posted a photo of was done with Tamco Products.

Hat's off to you, and excellent work!
Hey Michael,
You are of course correct in regard to the task of sanding these frames. I could check my notes but off the top of my head, I'd say I have well over 100 hours in this frame to date.
And to think this was a nice frame to begin with!

I've been using ChromaBase primer and Nason Ful-Thane color for years upon years.
Cost is reasonable and it has proven to last very well for years upon years.
I doubt I'll change but appreciate your advice. This stuff has worked so well, for so very long... plus, I know just how to handle it.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2019, 09:35 PM   #110
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Mike,


Under these things.
My gosh man! Good for you!

Ya know, you'd made a comment in an earlier post that "I am not alone".
You are correct but beyond you and I, well, we might be alone
I've had more than one person suggest that you and I are the only two remaining doing this type of (read OCD) work.

Here's a photo of the inside of the cab on that '40 PU I'd recently completed.
I ask you: How many guys (other than the two of us) that block out the interiors?
Attached Images
File Type: jpg floor aft.jpg (49.7 KB, 903 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2019, 09:40 PM   #111
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Interest in new restoration project thread?

Mike, as with anything when you find something that works, stick with it! Out of curiosity do you use Nason on the sheet metal as well?

I haven’t sprayed much DuPont products other than some chromabase (base coat) as it’s hard to find around here. I assume Nason is a DuPont product?

Again excellent work in a world where most frames receive krylon from walmart!
35fordtn is offline   Reply With Quote
Old 11-13-2019, 09:47 PM   #112
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Mike,

Under these things, but there is a fundamental difference in that what you show is your handiwork and in my photos, the handiwork is that of a couple of long-time good friends who happen to be world-class painters and paint preparers. My role is researcher, parts finder, and final assembler where the devil in the details.
David, you indeed have the best painters I’ve ever in my extremely inexperienced short life have encountered. One of your painters has thought me more in short conversations in the last two years about painting than I had ever learned before. Take that and add it to your extensive research and patience in correctly assembling them, and you get the final results that are typical of yours or Kubes cars in the fact that they are the best there is in the world of early v-8’s
35fordtn is offline   Reply With Quote
Old 11-13-2019, 10:01 PM   #113
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by '36 5W View Post
Ditto here; subscribed!
How do you subscribe?

Charlie Stephens
Charlie Stephens is offline   Reply With Quote
Old 11-13-2019, 11:02 PM   #114
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post

How many guys (other than the two of us) that block out the interiors?

This is but one example of what I was talking about in Post #99. DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 11-13-2019, 11:08 PM   #115
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,


Re. the '40 p.u.; super duper!
DavidG is offline   Reply With Quote
Old 11-14-2019, 12:56 AM   #116
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

great stuff!
Tinker is offline   Reply With Quote
Old 11-14-2019, 03:33 AM   #117
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

Mike,
On the frame, what do you do to ensure the doubled up area in the rear mostly, is clean? I find it very hard to clean, and even harder to paint properly. Is separating them an option?

Thank you,
Ralph
RalphM is offline   Reply With Quote
Old 11-14-2019, 08:48 AM   #118
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

We are not worthy!
Mart is offline   Reply With Quote
Old 11-14-2019, 09:04 AM   #119
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by RalphM View Post
Mike,
On the frame, what do you do to ensure the doubled up area in the rear mostly, is clean? I find it very hard to clean, and even harder to paint properly. Is separating them an option?

Thank you,
Ralph
This is one of those numerous areas Michael Driskall eluded to in his previous post. A definite pain in the butt... lots of effort to get this area clean and even more to get it smooth for painting.
The trick to preparing? Patience, lots of patience.
The trick to painting in those areas? For me, it's turn the pressure way down at the gun.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-14-2019, 09:51 AM   #120
Ian1932
Senior Member
 
Ian1932's Avatar
 
Join Date: Nov 2017
Location: Knoxville, TN
Posts: 317
Default Re: Interest in new restoration project thread?

Wow! Some nice looking paint jobs in this thread! I love watching people progress from rust and dents to glass like finishes! Watching...
Ian1932 is offline   Reply With Quote
Old 11-14-2019, 12:16 PM   #121
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

I was wondering how you eliminated blow back and bare spots when painting into an enclosed frame pocket. I still use a siphon gun on sheet metal topcoats even though I do have a high quality HVLP gun. The time involved in prep work and the cost of paint is such I am chicken to take a chance with something I am not completely used to. I still use the same siphon gun I bought in 1972 (DeVilbiss JGA 502).
Wish I could farm out the body/prep/paint work!
deuce_roadster is offline   Reply With Quote
Old 11-14-2019, 12:26 PM   #122
super flat
Senior Member
 
super flat's Avatar
 
Join Date: Jan 2011
Location: west bend wi
Posts: 314
Talking Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Some of you have expressed interest throughout the past that you'd enjoy a thread wherein I'd show the progress and perhaps some methods to one of my restorations.
I am just beginning a ground up, concourse restoration on a '40 Ford Business coupe.
So, the question is (kind of a poll), "who might enjoy this?"
Mind you, it (the restoration) will take approximately one year.
Please count me in!
__________________
I am usually relatively happy------Gary
super flat is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-14-2019, 12:30 PM   #123
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

V8: No doubt about it, when it comes to 40 Fords,
Mike is an "supranatural resource" with the patience of a toothache.
19Fordy is offline   Reply With Quote
Old 11-14-2019, 01:31 PM   #124
Randy in ca
Senior Member
 
Randy in ca's Avatar
 
Join Date: May 2010
Posts: 1,628
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Charlie Stephens View Post
How do you subscribe?

Charlie Stephens
-

Use "Thread Tools" on the red bar.
Randy in ca is offline   Reply With Quote
Old 11-14-2019, 06:41 PM   #125
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

A good day indeed!
Attached Images
File Type: jpg P1050344.JPG (164.0 KB, 1070 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-14-2019, 06:49 PM   #126
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by 35fordtn View Post
Mike, as with anything when you find something that works, stick with it! Out of curiosity do you use Nason on the sheet metal as well?

I haven’t sprayed much DuPont products other than some chromabase (base coat) as it’s hard to find around here. I assume Nason is a DuPont product?

Again excellent work in a world where most frames receive krylon from walmart!
Michael,
The Nason is simply that - Nason. No affiliation with DuPont that I am aware of.

I've been using DuPont Chromabase on the sheet metal for the last six cars or so. Typically four coats of color and three or four coats of clear. I figure on sanding off one coat of clear prior to buffing.
I have learned to manage the ChromaBase fairly well and have grown comfortable with it.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-14-2019, 07:11 PM   #127
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
A good day indeed!

Not too shabby, especially for a day that started-out at about 17 degrees. DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 11-14-2019, 09:19 PM   #128
melvinm39
Junior Member
 
Join Date: Jun 2015
Posts: 2
Default Re: Interest in new restoration project thread?

That would be great
melvinm39 is offline   Reply With Quote
Old 11-14-2019, 10:11 PM   #129
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Super!
DavidG is offline   Reply With Quote
Old 12-05-2019, 09:12 PM   #130
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sorry but now the project as always slows. The body work takes more time than any other part of my restorations. I'd mentioned in an earlier post that to keep me fairly sane, I will often prepare subassemblies while the body work continues - just for a little break in the action.
In the past week, I'd managed to complete quite a few things. The horn / bracket assembly as well as the headlamp bucket assemblies are ready to install. Some of you may note all of the requisite hardware is in place. Once I start assembling the car, I like to stay in the assembly mode and not have to switch in (and out of) the search mode.
Attached Images
File Type: jpg headlamps b4.jpg (62.3 KB, 100 views)
File Type: jpg headlamps aft.jpg (58.7 KB, 112 views)
File Type: jpg horns b4.JPG (94.6 KB, 99 views)
File Type: jpg horns after.JPG (97.1 KB, 100 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-05-2019, 09:18 PM   #131
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

The body work is going along actually quite well. In a different thread here on the Barn, the question was raised as to the quality of the reproduction rear tool tray pan.
Well, let's say it's "okay". Better than what I had for certain. Still, it required a lot of work to get it to fit properly. this one came from Pacific Parts. I do not know if they supply Drake and Carpenter. If you look at the photos carefully, you'll see I had to cut each side near the fender mount and move the panel in. About 1/8" was required on the left side, nearly 1/4" on the right side.
My guess is most guys would simply install this pan and figure "good enough". Me? I can't seem to force myself to accept "good enough". This pan was simply too wide. From my experience as a tool maker, it appears to have been formed poorly.
Anyway, it's welded up and the shape and width are now correct for a '40 Ford.
Attached Images
File Type: jpg P1050370.JPG (154.0 KB, 248 views)
File Type: jpg P1050371.JPG (143.0 KB, 246 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-05-2019, 09:22 PM   #132
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Managed to get the backing plate assemblies done as well. I have found it so much easier to have these ready to install to the spindles and rear axle housings as assemblies than build them on the chassis.
I did have to shorten the spring that is over the brake cable. The reproduction is fit with a spring at each end that is considerably longer than it was authentically and will cause issues if left as received.
Attached Images
File Type: jpg backing plate aft.jpg (27.2 KB, 203 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-05-2019, 09:39 PM   #133
Hal Beatty
Senior Member
 
Hal Beatty's Avatar
 
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
Default Re: Interest in new restoration project thread?

Looking good Mike!
Hal Beatty is offline   Reply With Quote
Old 12-05-2019, 10:42 PM   #134
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Interest in new restoration project thread?

Mike,
Might I ask how the ?!?! you remove the brake adjusters to have them plated??
35fordtn is offline   Reply With Quote
Old 12-05-2019, 10:48 PM   #135
copgib
Member
 
copgib's Avatar
 
Join Date: Aug 2017
Location: Williston, Florida
Posts: 82
Default Re: Interest in new restoration project thread?

count me in too! Hugh
copgib is offline   Reply With Quote
Old 12-07-2019, 12:45 PM   #136
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Made a bit more progress this past week. Ya laugh but here goes:
The trunk lid did not fit as well as I would like. It was in fact too close in many areas to the body. You can note in the photos some of my inked marks as to where I needed to cut the edges and where I needed to add to them. Now the lid fits beautifully.
Back fenders? I ended up cutting the flange that the attachment bolts go through in order to match the curve of the fenders with the curve of the body. Yes, the welt would conceal most of this mismatch but I'd know it was lurking. So, cutting the "flange" in a number of spots allowed me to move the fender around to where I was happy with it.
Yes guys... it is a sickness
Attached Images
File Type: jpg P1050376.JPG (151.5 KB, 336 views)
File Type: jpg P1050377.JPG (145.0 KB, 323 views)
File Type: jpg P1050378.JPG (153.5 KB, 228 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-07-2019, 01:24 PM   #137
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Nice work, Mike.

I can relate to this type of effort. We often have to remove thin sections of fenders not originally from the subject project car to ensure proper fit and once in a while even if the fender was original equipment to the car.

At times seriously original car bodies with original paint intact will show evidence of in-plant sheet metal 'adjustments'. Serious hammers were standard equipment in assembly plants until numerical control equipment minimized sheet metal variations that were previously inevitable in stamping operations.
DavidG is offline   Reply With Quote
Old 12-07-2019, 01:59 PM   #138
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Excellent work and discussion. It's good for all of us to know what it takes. How much of it we choose to apply is up to us, but at least we know what to do.

Thanks Mike (and the other contributors adding their thoughts).
Mart is offline   Reply With Quote
Old 12-07-2019, 02:08 PM   #139
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Nice work, Mike.

Serious hammers were standard equipment in assembly plants until numerical control equipment minimized sheet metal variations that were previously inevitable in stamping operations.

I went through the then-new Corvette factory in Bowling Green, Ky. back in September of 1982. It was amazing as we got toward the end of the line, to watch some of the beating-on, bending, jerking-on, tugging and whanging with fists and open palms to make various components fit something like the original design called for. Barbaric process for sure, yet most of 'em didn't look too shabby going out the big door. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 12-07-2019, 02:43 PM   #140
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

I think it's really cool that "Kube" is willing to share his knowledge and show the results with others. Lots of folks take it all with them on their last ride.
19Fordy is offline   Reply With Quote
Old 12-07-2019, 03:42 PM   #141
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
I think it's really cool that "Kube" is willing to share his knowledge and show the results with others. Lots of folks take it all with them on their last ride.
Is this my last ride? Oh my gosh! I didn't realize that. ARGGGHHHH!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-07-2019, 07:44 PM   #142
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Is this my last ride? ARGGGHHHH!

Yikes, NO....can't be!! TOO much still left to do. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-09-2019, 11:25 AM   #143
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

A Nason paint system was mentioned previously. I think they are now under the Axalta banner along with Dupont coatings by brand names. Dupont coatings was spun off some years ago to Axalta. I was around Nason way back when I worked in a NAPA warehouse while going to aviation school but I've not used any of there stuff. It's been a while since I used Imron Elite but it and Chromabase are also Axalta products now days.

I sort of avoid painting the helicopters now days because it's so much work with a million rivets to block around. Because of this, I'm well aware how much fun the frames and interior pieces would be to refinish. My hat is off to those that make the attempt.
rotorwrench is offline   Reply With Quote
Old 12-10-2019, 04:07 PM   #144
lazycarguy
Junior Member
 
Join Date: Dec 2015
Posts: 3
Default Re: Interest in new restoration project thread?

Yes!
lazycarguy is offline   Reply With Quote
Old 12-18-2019, 09:52 PM   #145
Larry
Member
 
Join Date: May 2010
Posts: 52
Default Re: Interest in new restoration project thread?

Hi Mike, I just found your thread on the restoration. Count me in. Thanks Larry
Larry is offline   Reply With Quote
Old 12-19-2019, 09:16 AM   #146
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Larry View Post
Hi Mike, I just found your thread on the restoration. Count me in. Thanks Larry
I haven't had too much to "show" lately. I've been working on the doors which were very nice to begin with as well as building up the differential / Columbia.
I probably should have photographed the process of replacing the torque tube bearing but once I was immersed in that project, I didn't "look up" until I was done. I am so happy I relieved my wallet years ago when offered the KR Wilson tools dedicated for this task.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-19-2019, 09:53 AM   #147
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

I'll bet it's cool to use tools specifically made for the task.
I search and search for a good deal on them. I completely understand what u mean when u say "relieve your wallet"
I ended up making some of the tools I used in rebuilding my Columbia. It's been a few years now since the rebuild and I've never had an issue with it since. Of course with the info from the guys on here it makes it a bit easier to achieve.
RobR'35 is offline   Reply With Quote
Old 12-19-2019, 10:57 AM   #148
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

I have my torque tubes powder coated on the outside and since they have been sandblasted inside and out, I Glyptol the inside of the tube so it won't rust. It is really effortless to pull in the new center bearing with the KRW tool. I sight down and line up the arrow on the tool with the hole for the grease fitting, wipe a little liquid soap on the outer rubber donut and it slides in up to the stop very easily, dead on the grease hole in the T tube with the grease hole in the rubber donut.
deuce_roadster is offline   Reply With Quote
Old 12-19-2019, 07:08 PM   #149
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by deuce_roadster View Post
I have my torque tubes powder coated on the outside and since they have been sandblasted inside and out, I Glyptol the inside of the tube so it won't rust. It is really effortless to pull in the new center bearing with the KRW tool. I sight down and line up the arrow on the tool with the hole for the grease fitting, wipe a little liquid soap on the outer rubber donut and it slides in up to the stop very easily, dead on the grease hole in the T tube with the grease hole in the rubber donut.
Spoken by a man that (obviously) has the KRW tool
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-20-2019, 10:17 AM   #150
Darrell S
Senior Member
 
Darrell S's Avatar
 
Join Date: Aug 2015
Location: Everett WA
Posts: 346
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Spoken by a man that (obviously) has the KRW tool
Could one of you guys that has the KRW tool please post a picture of it?
Darrell S is offline   Reply With Quote
Old 12-20-2019, 11:05 AM   #151
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

I will get to that later today.
deuce_roadster is offline   Reply With Quote
Old 12-20-2019, 12:42 PM   #152
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

The one I made is pretty much like the KRW and didn't cost much. This is a link to one that is similar to mine. Mine is more refined since I have a lot of resources at hand. The KRW stuff will cost more in money but less in time. Both get the job done.
https://www.fordbarn.com/forum/showt...eshaft+bearing

Last edited by rotorwrench; 12-20-2019 at 12:48 PM.
rotorwrench is offline   Reply With Quote
Old 12-20-2019, 03:46 PM   #153
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Pictures of KRW Torque Tube center bearing tool.[IMG][/IMG]

[/IMG]



Note the end the bearing goes on is solid with the shaft and has a square notch that a square rubber protrusion (which is in line with grease hole in the rubber) from the rubber the bearing is encased in locks the bearing so it cannot spin on the shaft.
At the transmission bell end note that the disk has an arrow to line up the tool with the grease fitting hole, I temporarily install a new grease fitting to more easily sight down and line up the tool. Also notice the groove in the shaft and the pin in the disk that prohibits the disk from turning on the shaft and prevents the shaft from turning relative to the disk. These things are what makes the tool so easy to use and accurate.

Last edited by deuce_roadster; 12-20-2019 at 04:31 PM. Reason: added pictures, more text
deuce_roadster is offline   Reply With Quote
Old 12-20-2019, 07:17 PM   #154
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Interest in new restoration project thread?

Thanks for sharing! Now about 200 of us can be on the look-out for one..... hahaha
Flathead Youngin' is offline   Reply With Quote
Old 12-21-2019, 02:14 PM   #155
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: Interest in new restoration project thread?

There is also a similar KRW tool for removing the old center bearing. This tool will allow you to remove the bearing without damaging it. Usually they are beyond reusing but occasionally one is still nice enough to use over.
40larry is offline   Reply With Quote
Old 12-22-2019, 09:08 AM   #156
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 40larry View Post
There is also a similar KRW tool for removing the old center bearing. This tool will allow you to remove the bearing without damaging it. Usually they are beyond reusing but occasionally one is still nice enough to use over.
I've got that tool as well. It looks pretty much like the installer but different dimensions. I can post photos if so desired.
I've never considered reusing that bearing as it's too much work to R&R after the car is restored and assembled.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-22-2019, 10:34 AM   #157
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

I have taken a few bearings out where the bearing look OK but the rubber was like bubble gum.
deuce_roadster is offline   Reply With Quote
Old 12-22-2019, 11:15 AM   #158
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

Rubber in it's natural form, doesn't have a very long life span even if kept in controlled environments. Neoprene lasts longer but is still life limited and vulnerable to ozone and some solvents. The fluorocarbon and fluorosilicon elastomers have the longest shelf and working life but they are more expensive to produce. Both were developed in the mid 50s due to a need for low and high temp seals for aerospace applications with good swell resistance to lubricants and solvents. If they could use more modern elastomers, to reproduce stuff like this then it would last a very long time. I'm not sure what is used on the ones Skip sells but it is likely neoprene.
rotorwrench is offline   Reply With Quote
Old 12-23-2019, 11:53 AM   #159
Cecil/WV
Senior Member
 
Cecil/WV's Avatar
 
Join Date: May 2010
Location: Gerrardstown, WV
Posts: 2,265
Default Re: Interest in new restoration project thread?

Skip Haney sent me instructions along with the center bearing on how to install the bearing with a tool fabricated from PVC pipe. Worked great and was cheap to make! used it on my '40 pickup.
Cecil/WV is offline   Reply With Quote
Old 12-23-2019, 05:16 PM   #160
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Is Skip's bearing a sealed bearing or is the grease fitting on the TT still in play?
Good use of this thread while waiting for the next installment of pictures from Kube!
deuce_roadster is offline   Reply With Quote
Old 12-24-2019, 11:31 AM   #161
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by deuce_roadster View Post
Is Skip's bearing a sealed bearing or is the grease fitting on the TT still in play?
Good use of this thread while waiting for the next installment of pictures from Kube!
Nothing too interesting to post lately. Have the seat tracks re-plated and will soon reassemble them.
I might, if time allows, complete the differential today. If so, I'll post that stuff.

Merry Christmas to all! Let's hope 2020 is bright, peaceful and we all stay healthy.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-24-2019, 11:49 AM   #162
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

The photos that I've seen indicate that is has a grease port on the outer race.
rotorwrench is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-24-2019, 01:14 PM   #163
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Mike, I would tend to say that all steps even mundane ones you take are interesting due to the exactness and quality of your work.
Merry Christmas to you and " Let's hope 2020 is bright, peaceful and we all stay healthy" that would be the best gift of all! Thanks!
deuce_roadster is offline   Reply With Quote
Old 12-24-2019, 03:52 PM   #164
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Interest in new restoration project thread?

Merry Christmas to you Mike and all the other '40 Ford lovers. Best looking old Ford that Henry ever built.
TJ is offline   Reply With Quote
Old 12-25-2019, 11:14 AM   #165
Cecil/WV
Senior Member
 
Cecil/WV's Avatar
 
Join Date: May 2010
Location: Gerrardstown, WV
Posts: 2,265
Default Re: Interest in new restoration project thread?

It has been a while, but I think it is a sealed bearing. although I do remember lining up for the fitting.
Cecil/WV is offline   Reply With Quote
Old 12-25-2019, 11:39 AM   #166
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Cecil/WV View Post
It has been a while, but I think it is a sealed bearing. although I do remember lining up for the fitting.

Here are a couple of pictures of Skip's bearing. DD





__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 12-28-2019, 10:02 AM   #167
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Good day fellas!
Now that the seasonal rush is over, I should have a little more time to "play". I'm certain most of you can understand the need to get your hands dirty.
I did manage to get the differential together along with the Columbia overdrive. Went to install the (finished) radius rods and discovered a huge oversight on my part. The right rod was bent where it bolts to the axle housing. ARGGHH! How I missed this is beyond me but I did - a certain "Bozo" moment. That set me back as I really wanted to have this entire assembly tucked beneath the car by now.
Just plain stupid at times

Today I am planning on wrapping the springs. I'll try to remember to take a few photos of that process. It's tedious work but in my opinion worth the efforts.
Attached Images
File Type: jpg P1050392.JPG (157.0 KB, 156 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-28-2019, 12:51 PM   #168
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Managed to get the rims painted yesterday. I wish all the rims I restore were as nice as these. Not a pit nor ding on any of them.
Attached Images
File Type: jpg P1050391.JPG (155.5 KB, 126 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-28-2019, 01:04 PM   #169
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Interest in new restoration project thread?

Hey, Kube, tell us about your setup..... dedicated paint room? dirty tear down area? clean storage area?

Thanks for the update and keep telling us about your process....

The rims looks wonderful
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Old 12-28-2019, 02:05 PM   #170
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Flathead Youngin' View Post
Hey, Kube, tell us about your setup..... dedicated paint room? dirty tear down area? clean storage area?

Thanks for the update and keep telling us about your process....

The rims looks wonderful
Dedicated body work / paint area. NOT the best situation but the one I'd found myself in. LOTS of cleaning before any spraying is done.
All of the disassembly is done in another area away from this room. Again, NOT the best situation but I have managed to make it work. Yes, you can read bull headed stubbornness in to that

VERY clean storage area.
__________________
"I can explain it for you. However, I can't understand it for you".

Last edited by Kube; 12-28-2019 at 02:57 PM.
Kube is offline   Reply With Quote
Old 01-01-2020, 10:01 AM   #171
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Installed the spring perch pins yesterday as well as the spring covers.
I always install NOS (OEM) springs o restore the proper / designed height and handling characteristics to the vehicle. I clean and powder finish the individual leaf's and apply a thin coat of fifth axle grease between each leaf upon assembly.
The KRW tool makes installing the pins a breeze - perhaps 5 minutes each maximum.
The covers were NOS, my last set. Note the spring must be flat in order to install these. The entire job took a bit more than three hours.
Attached Images
File Type: jpg P1050393.JPG (147.5 KB, 212 views)
File Type: jpg P1050395.JPG (141.0 KB, 213 views)
File Type: jpg P1050396.JPG (150.0 KB, 204 views)
File Type: jpg P1050398.JPG (149.5 KB, 206 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 01-01-2020, 10:14 AM   #172
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

Very cool Kube. You do some impressive work.
RobR'35 is offline   Reply With Quote
Old 01-01-2020, 10:16 AM   #173
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Kube, Happy 2020. Thanks for posting the photos of how you install the spring covers. I never knew how it was done. Sure is a neat spring holder (flattener) device. You sure do a 100 point restoration that a lucky customer will enjoy.
19Fordy is offline   Reply With Quote
Old 01-01-2020, 10:57 AM   #174
av8coupe
Senior Member
 
Join Date: Jun 2010
Location: Wilbraham MA
Posts: 150
Default Re: Interest in new restoration project thread?

Somehow I just discovered this thread, so I ushered in 2020 binge reading. Thanks for sharing your expertise and approach to turning out cars that most of us only dream about. Subscribed from here out...
av8coupe is offline   Reply With Quote
Old 01-01-2020, 11:28 AM   #175
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Guys, thanks for the kind words.
I can't take credit for the spring "jig". It's kind of a copy of the KR Wilson fixture.
The only thing I'd wish I'd done differently is make the bottom channel out of aluminum. Of course, when I made this, I was younger (stronger). It seems the older I get, the heavier stuff becomes. Hmmm???

happy new year to all!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 01-01-2020, 11:54 AM   #176
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

Mike,
I have a set of shackle bushings to do and was considering making a tool like that out of an old C clamp, or possibly making adapters for my ball joint press.
Do you have any better pictures of it?
Thanks,
Ralph
RalphM is offline   Reply With Quote
Old 01-01-2020, 12:24 PM   #177
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by RalphM View Post
Mike,
I have a set of shackle bushings to do and was considering making a tool like that out of an old C clamp, or possibly making adapters for my ball joint press.
Do you have any better pictures of it?
Thanks,
Ralph
Ralph, I'll try to take some nice shots of the tool later today. I have heard of guys making a comparable tool out of a ball joint press. I have not heard how well they'd worked. I'd think they would be fine for a spring but the axle housings and front axle??? I'd think the close proximity of the housing / axle would require a smaller bodied tool such as the KRW.
On occasion, these are offered on eBay. They seem to go in the $250+ range without the adapters. The adapters can be made easy enough if a guy has decent lathe skills.
I am not certain how a C-clamp might work as there needs to be a bushing at the "far end" to center the installation of the pin.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 01-01-2020, 12:35 PM   #178
Flathead Youngin'
Member
 
Join Date: Oct 2019
Location: Kentucky
Posts: 69
Default Re: Interest in new restoration project thread?

It has VERY fine looking threads too.....more torque?
__________________
"Constipated, can't pass a thing! Don't laugh, bud, your daughter may be in here. They don't call 'em flyn' flatheads for nothin'!"
Hot Rod (Kennie) Holmes
Flathead Youngin' is offline   Reply With Quote
Old 01-01-2020, 12:44 PM   #179
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

When I did my rear spring on my AV8, I had a new spring, but drive in new pins with a tool/hammer. Not the best way, but spring was warm and I put bushings outside at -30, so it went ok.
But when it came to the axle perches I cheated and used modern slip in bushings made to look like original.
RalphM is offline   Reply With Quote
Old 01-01-2020, 01:44 PM   #180
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Ralph, the spring ends are easier because it can open up as pressure is being applied. It is a whole different story on the rear axle housings and front end parts as Kube explained there is less room. I have the KRW tool and remember what a war it was before I got it. I don't think a C clamp frame is ridged enough for doing the hard (solid steel hole areas) the KRW tool is VERY stout.
deuce_roadster is offline   Reply With Quote
Old 01-01-2020, 03:10 PM   #181
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by RalphM View Post
Mike,
I have a set of shackle bushings to do and was considering making a tool like that out of an old C clamp, or possibly making adapters for my ball joint press.
Do you have any better pictures of it?
Thanks,
Ralph
Ralph,
Does this help? Let me know please.
Note the bushing on the working end is both internally relived as well as threaded. It gets threaded on to the pin until it bottoms out against the pin body. That way, both the pin and body are pressed simultaneously. The other end fits nearly size for size within the "far end" of the tool. That bushing is relieved so it fits nearly size for size within the perch and spring ends. Of course, the inside of this bushing is relieved to allow the pin to enter it during installation.
Attached Images
File Type: jpg P1050399.JPG (152.5 KB, 143 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 01-01-2020, 04:08 PM   #182
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

Thank you! Yes that helps. The tool that I used to hammer the bushing in before is kind of the same way it screws onto the stud and then bottoms out on the sleeve so that you press the bushing in all as one piece. Maybe I can modify that and make it work on a screw type press.
I have a friend with a lathe and I believe that he could make the sleeve for the other end without any problems.
These bushings are going in a 1947 front and and as you say the only drawback is getting a tool that will fit with the axle /wishbone assembly in place.
RalphM is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-01-2020, 04:35 PM   #183
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

For what it's worth I once improvised a press for the rear axle perch bushings on the 33. I put the bushes in the spring using a good bench vise. I couldn't do that with the axle so took the vise to the axle. It worked well.

Mart.
Mart is offline   Reply With Quote
Old 01-01-2020, 06:26 PM   #184
KiWinUS
Senior Member
 
KiWinUS's Avatar
 
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,945
Default Re: Interest in new restoration project thread?

This kit can be modified for many uses. Pushing out & pulling in wheel studs is just one. It may be able to be modified for shackles https://www.harborfreight.com/ball-j...les-63279.html
Great work Kube.
KiWinUS is offline   Reply With Quote
Old 02-05-2020, 08:08 PM   #185
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Nope, I haven't stopped working on this coupe - just not much interesting to report. At this point ALL of the metal work is done. Now it's down to the finish work. The roof was the last part to metal finish - that got completed today.
Attached Images
File Type: jpg P1050470.JPG (153.5 KB, 252 views)
File Type: jpg P1050313.JPG (147.5 KB, 237 views)
File Type: jpg P1050471.JPG (154.0 KB, 240 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 02-05-2020, 09:40 PM   #186
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,541
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
why all the grinding on the roof, hail damage?
cas3 is offline   Reply With Quote
Old 02-06-2020, 12:42 AM   #187
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Could be metalworking rust pits. I did a lot of that on my avatar roadster, hadn't thought of hail damage. Don't see that in this area.
deuce_roadster is offline   Reply With Quote
Old 02-06-2020, 02:20 AM   #188
Raffyjoy1102
Junior Member
 
Join Date: Sep 2019
Posts: 9
Default Re: Interest in new restoration project thread?

Yes!!!
Raffyjoy1102 is offline   Reply With Quote
Old 02-06-2020, 09:07 AM   #189
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by deuce_roadster View Post
Could be metalworking rust pits. I did a lot of that on my avatar roadster, hadn't thought of hail damage. Don't see that in this area.
You got it! Very small rust pits.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 02-06-2020, 09:33 AM   #190
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

So, how do you treat the small rust spots, spot sandblast or chemically?

I would also like to see more pictures of the tailpan and toolbox replacement. I have that repair to deal with on my '37 coupe.

Thanks for taking us along on this project.
Zeke3 is online now   Reply With Quote
Old 02-06-2020, 10:10 AM   #191
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
So, how do you treat the small rust spots, spot sandblast or chemically?

I would also like to see more pictures of the tailpan and toolbox replacement. I have that repair to deal with on my '37 coupe.

Thanks for taking us along on this project.
Zeke,
First, the entire body gets (plastic) bead blasted. The pros of this method? NO warping and NO pitting of the sheet metal. The cons? It won't remove rust. On the plus side, it makes it that much easier to see even the smallest rust spot for proper repair / metal replacement.
I do some sand blasting. Areas like the gutters and other difficult areas to access.
I never use any chemical stripping agents on any part that has lapped sheet metal or other area(s) that may have the (remote) possibility the chemical may not be thoroughly cleansed. Too many times, I've seen chemicals come back to "haunt" an otherwise beautiful paint job. It can take years but it too often can have disastrous effects. In my opinion - why chance it?

I'll see what I can find for the tail pan R&R. I will strongly advise you to remove the old pan by spot facing ALL of the authentic spot welds and removing the lead at the factory seam. Also, only tack the new pan in place and fit both the trunk lid, the trunk latch and both rear fenders before committing to the pan's installation.
The pans I'd purchased from Drake many years ago were very nice and required very little to fit properly. The current pans on the market are "okay" at best and require some serious modification to fit the way I demand of my own work.
__________________
"I can explain it for you. However, I can't understand it for you".

Last edited by Kube; 02-06-2020 at 10:16 AM.
Kube is offline   Reply With Quote
Old 02-06-2020, 10:17 AM   #192
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Zeke,
These three photos were all I took of the rear pan installation. What is not shown is the fact I needed to remove approximately 3/16" vertically from both sides of the pan where it bolts to the fenders. Simply put, the repop pan was a tad wider than the authentic pan.
There was also some modification required where the lip the rubber seal goes on meets the adjoining lip of the body. The lip on the repop pan was much taller than the authentic pan. Easy fix but something to watch for.
Attached Images
File Type: jpg P1050370.JPG (154.0 KB, 188 views)
File Type: jpg P1050315.JPG (143.5 KB, 192 views)
File Type: jpg P1050337.JPG (143.0 KB, 188 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 02-06-2020, 02:56 PM   #193
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Excellent work Mike. Thanks for taking the effort to post up the pics.

Mart.
Mart is offline   Reply With Quote
Old 02-06-2020, 03:14 PM   #194
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Kube, thank you for the additional information. I remembered you had said earlier in the thread about plastic bead blasting the sheet metal. I was not aware of the limitation this process not removing rust.

I also understand your concern about chemical stripping with seams and lapped joints, I have seen the telltale signs of the chemical leaching out of seams years after the body was dipped.

I think my options for a repop tailpan for a 37 coupe are pretty limited, EMS or make it myself. I did find an article in an old V-8 Times issue discussing how a fellow made a repair tail pan panel. That will be a challenge.

Again, thanks for putting this thread together. I enjoy following along.
Zeke3 is online now   Reply With Quote
Old 02-06-2020, 03:54 PM   #195
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
Kube, thank you for the additional information. I remembered you had said earlier in the thread about plastic bead blasting the sheet metal. I was not aware of the limitation this process not removing rust.

I also understand your concern about chemical stripping with seams and lapped joints, I have seen the telltale signs of the chemical leaching out of seams years after the body was dipped.

I think my options for a repop tailpan for a 37 coupe are pretty limited, EMS or make it myself. I did find an article in an old V-8 Times issue discussing how a fellow made a repair tail pan panel. That will be a challenge.

Again, thanks for putting this thread together. I enjoy following along.
As you are no doubt already aware of... EMS makes poopy for the most part. The pan from them might, just might, be a decent starting point. I wish you the best with this.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 02-06-2020, 04:21 PM   #196
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Interest in new restoration project thread?

I used the EMS pan on a '37 and it is a good starting point. It does take some maneuvering to get it to fit. The lip for the rubber seal is definitely too wide and will need trimming. Unless they have changed, they do not put the bumper iron cutouts in the pan. I'm not sure, but I thought that McPherson College in Kansas was making some panels for '37 in their restoration shop.
TJ is offline   Reply With Quote
Old 02-06-2020, 05:51 PM   #197
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Great work as always, Mike.
DavidG is offline   Reply With Quote
Old 02-06-2020, 06:17 PM   #198
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

TJ, I will follow up on that tip.
Zeke3 is online now   Reply With Quote
Old 02-06-2020, 07:37 PM   #199
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Great work as always, Mike.
Gosh Dave, coming from you means a ton to me. Thank you.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 02-06-2020, 10:08 PM   #200
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,


You're welcome as it is earned.
DavidG is offline   Reply With Quote
Old 04-12-2020, 10:32 AM   #201
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Yikes! I kind of forgot about this thread. Things like "life" got in the way I suppose.
Here's a little "catch up" on how this project is proceeding. Time to dedicate to it has been sparse recently. However, I have managed to get a number of things completed.
The dash, steering wheel, column, all window bezels, etc. are done.

Body has now had the second prime done and for the most part, it's blocked out. One more coat of prime, another block and wet sand should be enough.
Attached Images
File Type: jpg dash aft frt.JPG (149.5 KB, 231 views)
File Type: jpg dash aft rear.JPG (153.0 KB, 217 views)
File Type: jpg r quarter.JPG (150.0 KB, 217 views)
File Type: jpg floor.JPG (150.0 KB, 213 views)
File Type: jpg firewall.JPG (157.5 KB, 202 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-12-2020, 12:11 PM   #202
Hal Beatty
Senior Member
 
Hal Beatty's Avatar
 
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
Default Re: Interest in new restoration project thread?

Looks great! Thanks for the update.
Hal Beatty is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-12-2020, 02:51 PM   #203
jstrez5
Senior Member
 
Join Date: Aug 2012
Location: PA
Posts: 263
Default Re: Interest in new restoration project thread?

Cant wait for you to start jim s.
jstrez5 is offline   Reply With Quote
Old 04-12-2020, 04:50 PM   #204
Old School Iron
Junior Member
 
Join Date: Apr 2020
Location: Bellevue, Nebraska
Posts: 3
Default Re: Interest in new restoration project thread?

For sure! That would be cool. Ready to learn! Thanks
Old School Iron is offline   Reply With Quote
Old 04-12-2020, 11:56 PM   #205
Mike Conshafter
Senior Member
 
Mike Conshafter's Avatar
 
Join Date: May 2010
Location: Detroit
Posts: 140
Default Re: Interest in new restoration project thread?

This is the definition of perfection. What color are you going with Mike?
Mike Conshafter is offline   Reply With Quote
Old 04-13-2020, 01:22 AM   #206
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Mike Conshafter View Post
This is the definition of perfection. What color are you going with Mike?

THIS...…..is the definition of "Perfection"! This is a convertible Mike did several years ago. This car since sold at a Sotheby's Auction for $165K....and you heard that correctly! This is the car that Mike now jokingly refers to as the one that was docked 1 point, which resulted in a score of 999 because of two tiny pits a judge found on one of the rear axle bells. Kubarth does some nice stuff, no? DD








………………..
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 04-13-2020, 08:34 AM   #207
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Mike Conshafter View Post
This is the definition of perfection. What color are you going with Mike?
Hey Mike,
This one will be Folkstone Gray. Black wall tires. Mohair interior.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-13-2020, 08:42 AM   #208
KGS
Senior Member
 
KGS's Avatar
 
Join Date: May 2010
Location: Schooley's Mountain
Posts: 530
Thumbs up Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Hey Mike,
This one will be Folkstone Gray. Black wall tires. Mohair interior.
Kube, Perfect color choice. Ken
KGS is offline   Reply With Quote
Old 04-13-2020, 01:13 PM   #209
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

Incredibly nice!
RobR'35 is offline   Reply With Quote
Old 04-13-2020, 05:07 PM   #210
38bill
Senior Member
 
38bill's Avatar
 
Join Date: Apr 2014
Location: Minnesota
Posts: 1,162
Default Re: Interest in new restoration project thread?

Kube, do you keep track of the hours you spend on a restoration?
38bill is offline   Reply With Quote
Old 04-13-2020, 07:54 PM   #211
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 38bill View Post
Kube, do you keep track of the hours you spend on a restoration?
Fairly well, yes.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-15-2020, 06:10 PM   #212
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Today is kind of exciting for me. Sprayed a light guide coat on yesterday and began the wet sand process today. Once I have the entire body sanded out, I'll do another guide coat and repeat the wet sand process.
I sand in four directions which ultimately provides a STRAIGHT body regardless of the angle one may look at it.
Attached Images
File Type: jpg guide coat.JPG (153.0 KB, 637 views)
File Type: jpg guide coat +1.JPG (149.0 KB, 114 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-15-2020, 07:30 PM   #213
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Kube….I'm gonna show my possible dumbness here, or at least some long-term memory loss, but do all '40s have that double "hole/slot" at every fender bolt location (as seen in your pic) or is that something you possibly dreamed-up to aid in perfectly aligning the fenders to the requisite "Kubarth Standard"? That's gonna be another "sweetie" straight out of Wisconsin. DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 04-15-2020, 08:34 PM   #214
STEVE O
Senior Member
 
STEVE O's Avatar
 
Join Date: May 2010
Location: QUICKSBURG VA
Posts: 706
Default Re: Interest in new restoration project thread?

delete
STEVE O is offline   Reply With Quote
Old 04-15-2020, 09:13 PM   #215
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

The nut for the rear fender bolt is on a special clip that is held by the rectangular hole, bolt goes through the round hole. I don't know if other years use this or not. 39 might. 40 is my newest old Ford.
deuce_roadster is offline   Reply With Quote
Old 04-15-2020, 09:21 PM   #216
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Thanks Mike! I just didn't remember seeing that slot configuration in the past. Dick D
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 04-15-2020, 09:49 PM   #217
Mike Conshafter
Senior Member
 
Mike Conshafter's Avatar
 
Join Date: May 2010
Location: Detroit
Posts: 140
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
THIS...…..is the definition of "Perfection"! This is a convertible Mike did several years ago. This car since sold at a Sotheby's Auction for $165K....and you heard that correctly! This is the car that Mike now jokingly refers to as the one that was docked 1 point, which resulted in a score of 999 because of two tiny pits a judge found on one of the rear axle bells. Kubarth does some nice stuff, no? DD


………………..
I’m not going to argue that one...lol. Beyond impressive and worthy of a poster size print. Restorations of this level can justify an amount of that caliber. Talent is one thing, it’s when combined with a person that is detail oriented and the willingness to research for days on end that perfection shows. It’s the correct fastener finished correctly and installed in the correct direction.....and so on.
Mike Conshafter is offline   Reply With Quote
Old 04-15-2020, 10:00 PM   #218
Mike Conshafter
Senior Member
 
Mike Conshafter's Avatar
 
Join Date: May 2010
Location: Detroit
Posts: 140
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Hey Mike,
This one will be Folkstone Gray. Black wall tires. Mohair interior.

Man, you’re speaking my language. Gray tones with black walls are simple but tough and yet very striking. Ford had so many great darker colors throughout the 30’s and 40’s.
Mike Conshafter is offline   Reply With Quote
Old 04-15-2020, 10:18 PM   #219
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,844
Default Re: Interest in new restoration project thread?

Like many others, I am in awe of your work. I hope to someday see your work in person.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is online now   Reply With Quote
Old 04-15-2020, 10:58 PM   #220
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: Interest in new restoration project thread?

Wow great work ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 04-16-2020, 01:13 AM   #221
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Mike your work is subpar and is subject. Hahaha, just a stupid joke. Brilliant work. Thanks for sharing.




I did mean subject (something we talk about "a person or thing that is being discussed, described, or dealt with".). Humor is subjective. For me that can be hit or miss.



I didn't want to add nonsense explaining this on Kubes thread with a new post. So I replied in this post.


Amazing work!!! as always.

Last edited by Tinker; 04-17-2020 at 09:30 PM.
Tinker is offline   Reply With Quote
Old 04-16-2020, 03:07 AM   #222
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Tinker View Post
Mike your work is subpar and is subject. Hahaha, just a stupid joke. Brilliant work. Thanks for sharing.

Did ya mean "suspect" vs subject? DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-16-2020, 08:00 AM   #223
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by deuce_roadster View Post
The nut for the rear fender bolt is on a special clip that is held by the rectangular hole, bolt goes through the round hole. I don't know if other years use this or not. 39 might. 40 is my newest old Ford.
Hey Mike! You are correct about '39 having the same clips. Here's a photo of a '40 coupe I did last year or the year before. Gosh, time flies...
Attached Images
File Type: jpg left rear well aft.jpg (46.3 KB, 805 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-16-2020, 08:02 AM   #224
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I want to thank all of you guys for the very kind responses.
I do not feel worthy of them. I'm just a guy with a case of OCD that has been fortunate in the way it (the OCD) has manifested itself.
Still, you guys are appreciated! Thank you all...
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-16-2020, 06:24 PM   #225
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

Oh the raw fingertips. Sanding around all the rivets on an aircraft fuselage always made my hands a little too soft. There wasn't much skin left after getting things all blocked & smooth. The cars aren't as bad but it still takes its toll.
rotorwrench is offline   Reply With Quote
Old 04-16-2020, 06:29 PM   #226
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Mike, thanks for sharing. You have the patience of a toothache and the talent of a fine
Tiffeny jeweler. So great to see such excellence.
19Fordy is offline   Reply With Quote
Old 04-16-2020, 06:32 PM   #227
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Look at the lengths that this maniac with OCD goes to....notice the white wrap on the rear housing and spring for protection. It's no wonder these things finish-up so damned nice! DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 04-27-2020, 07:49 PM   #228
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Getting mighty close to some color! Just finishing the first phase of wet sanding. Floor pans are tedious and as such got left for last.
Attached Images
File Type: jpg floor bottom b4 -1.JPG (153.0 KB, 173 views)
File Type: jpg floor bottom b4 -2.JPG (150.5 KB, 154 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-27-2020, 10:51 PM   #229
rich b
Senior Member
 
rich b's Avatar
 
Join Date: May 2010
Location: Minnesota
Posts: 1,813
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Getting mighty close to some color! Just finishing the first phase of wet sanding. Floor pans are tedious and as such got left for last.
Wow; that floor is pretty.
rich b is offline   Reply With Quote
Old 04-27-2020, 11:56 PM   #230
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

Looking good!
So are most of your components done already? Meaning once the body is painted do you start assembling everything?
RalphM is offline   Reply With Quote
Old 05-04-2020, 05:13 PM   #231
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by RalphM View Post
Looking good!
So are most of your components done already? Meaning once the body is painted do you start assembling everything?
Pretty much - yes.
I maintain a number of shelves dedicated for only the current project. Safe and clean in my basement. Boxes of parts are inventoried so I can easily find whatever it is I am looking for.
One might think I am patient and I suppose for the most part, I am.
Mt patience runs short when I am assembling something and find I don't have "X" and must either wait to find it and / or rebuild & refinish.
nearly every single piece is restored and ready to install once the body is placed back on the chassis.
I really enjoy the assembly process
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-04-2020, 05:17 PM   #232
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Got the floor and inside painted today. After it cures for a day or two, I'll paint the bottom of the floors.
Attached Images
File Type: jpg P1050842.JPG (159.0 KB, 179 views)
File Type: jpg P1050843.JPG (155.5 KB, 161 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-04-2020, 05:23 PM   #233
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Nearly every single piece is restored and ready to install once the body is placed back on the chassis.
I really enjoy the assembly process

I too always got really excited once all traces of dirt, rust and grunge were history, the paint was cured and slick WITHOUT runs, your fingernails were finally clean and presentable again, and you could leisurely sit down and begin gluing cool stuff back together again. Looks like you're getting close to completing another one for the books! DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 05-04-2020, 05:29 PM   #234
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
I too always got really excited once all traces of dirt, rust and grunge were history, the paint was cured and slick WITHOUT runs, your fingernails were finally clean and presentable again, and you could leisurely sit down and begin gluing cool stuff back together again. Looks like you're getting close to completing another one for the books! DD
Leisurely sit down?
I've heard of such things as leisure. Methinks nothing but Folklore.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-04-2020, 05:40 PM   #235
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Leisurely sit down?
I've heard of such things as leisure. Methinks nothing but Folklore.

HEY Mister.....The Coopman "perfected" leisure many moons ago! DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 05-04-2020, 05:43 PM   #236
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
HEY Mister.....The Coopman "perfected" leisure many moons ago! DD
So IT does exist! Amazing. I'll need to see it in (in)action some day - just to confirm the reailty.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-04-2020, 05:57 PM   #237
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
So IT does exist! Amazing. I'll need to see it in (in)action some day - just to confirm the reailty.

What ya gotta understand is that my "leisure" here in Texas comes with a couple of qualifications, which might explain why I'm still a little behind with some project deadlines, but I NEVER did miss an appointment with a cool Corona on a porch in the shade! DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 05-04-2020, 09:30 PM   #238
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

Lol, love it!
RobR'35 is offline   Reply With Quote
Old 05-08-2020, 05:43 PM   #239
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Got the bottom painted today.
Guys, at my age, this is porn
Attached Images
File Type: jpg floor bottom aft 1.JPG (155.5 KB, 152 views)
File Type: jpg floor bottom aft 2.JPG (154.5 KB, 147 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-08-2020, 05:46 PM   #240
RobR'35
Senior Member
 
RobR'35's Avatar
 
Join Date: Dec 2014
Location: Upper Peninsula, Michigan
Posts: 604
Default Re: Interest in new restoration project thread?

The detail and lengths you go is really something.
RobR'35 is offline   Reply With Quote
Old 05-08-2020, 05:50 PM   #241
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by RobR'35 View Post
The detail and lengths you go is really something.
Something = insanity .
Still, I am happily insane.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-08-2020, 05:51 PM   #242
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Got the bottom painted today.
Guys, at my age, this is porn
That is very impressive, but I hope I never get as old as you.
tubman is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-08-2020, 06:49 PM   #243
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by tubman View Post
That is very impressive, but I hope I never get as old as you.
You may want to rethink that. Ya know, if the gap widens in our respective ages, one of us is no longer breathing.
Me? I'd prefer the gap in ages remains exactly as it currently is.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-13-2020, 05:23 PM   #244
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Tomorrow is a sweet day for me... all ready to apply some color.
Attached Images
File Type: jpg P1050882.JPG (150.0 KB, 116 views)
File Type: jpg P1050883.JPG (154.5 KB, 105 views)
File Type: jpg P1050884.jpg (30.0 KB, 107 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-13-2020, 05:45 PM   #245
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Excellent. Unless it's proprietary info, please let us know what color, brand and type of paint you use. Thanks.
19Fordy is offline   Reply With Quote
Old 05-13-2020, 05:52 PM   #246
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by 19Fordy View Post
Excellent. Unless it's proprietary info, please let us know what color, brand and type of paint you use. Thanks.
Proprietary? I have few secrets
CroMax base.
Folkstone gray.
__________________
"I can explain it for you. However, I can't understand it for you".

Last edited by Kube; 05-14-2020 at 03:33 PM. Reason: spelling error
Kube is offline   Reply With Quote
Old 05-13-2020, 10:06 PM   #247
TomT/Williamsburg
Senior Member
 
TomT/Williamsburg's Avatar
 
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,646
Default Re: Interest in new restoration project thread?

You do such nice work, Kube ......
TomT/Williamsburg is offline   Reply With Quote
Old 05-14-2020, 02:04 AM   #248
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Very nice Mike. Mr Kube.
Tinker is offline   Reply With Quote
Old 05-14-2020, 08:34 AM   #249
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Thanks for the kind comments guys.
Ya know, I truly enjoy these projects. Not really "work", well, for the most part anyway. Occasionally I want to pull my hair out. I refrain as I figure at my age, pulled out and it ain't growing back...
I am hoping that by this evening I'll be the proud poppa of a shiny gray coupe
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-14-2020, 09:30 AM   #250
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Wishing you all the best when you pull the trigger.
My 40 was orginally Folkstone Grey. Nice color.
Attached Images
File Type: jpg IMG_4941b.jpg (41.3 KB, 68 views)
19Fordy is offline   Reply With Quote
Old 05-14-2020, 11:22 AM   #251
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
Wishing you all the best when you pull the trigger.
My 40 was orginally Folkstone Grey. Nice color.
I'll be starting soon. Never did a coupe in this color. A '40 Ford convertible and a Merc, but never a coupe.
I think it'll be a neat "change" of pace.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-14-2020, 03:15 PM   #252
tcave
Junior Member
 
Join Date: Jun 2016
Posts: 2
Default Re: Interest in new restoration project thread?

Just found this thread , thanks for taking the time and effort to do it. I am really enjoying it.
tcave is offline   Reply With Quote
Old 05-14-2020, 05:59 PM   #253
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Oh happy day!
Attached Images
File Type: jpg P1050887.JPG (152.5 KB, 566 views)
File Type: jpg P1050888.JPG (158.5 KB, 121 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-14-2020, 07:12 PM   #254
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Just WOW, Kubarth! It WAS a good day!! DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 05-14-2020, 07:50 PM   #255
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Mike, I see an 1/8 inch drip right below the end of the drip rail.

Just kidding! You did a beautiful job.
CONGRATULATIONS. It's gorgeous.
19Fordy is offline   Reply With Quote
Old 05-14-2020, 07:54 PM   #256
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
Mike, I see an 1/8 inch drip right below the end of the drip rail.

Just kidding! You did a beautiful job.
CONGRATULATIONS. It's gorgeous.
I over read the "just kidding" part and subsequently had a mild heart attack! Just kidding - um, about the heart attack part.
I did get two small runs in the rear quarter. I'll (carefully) get them out. Wanted to cry. Still do.
Decided to have a brandy instead.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-14-2020, 07:57 PM   #257
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Mike, Sorry. Didn't mean for your heart to skip a beat.

Is this how you do it? Is water borne basecoat/ clear coat hard to do?
https://www.cromax.com/eu/en_GB/prod...-basecoat.html
19Fordy is offline   Reply With Quote
Old 05-14-2020, 08:09 PM   #258
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
Mike, Sorry. Didn't mean for your heart to skip a beat.

Is this how you do it? Is water borne basecoat/ clear coat hard to do?
https://www.cromax.com/eu/en_GB/prod...-basecoat.html
I should have been more specific. I use their uretahane, not the water base. Three coats of color after the initial "tack' coat. I follow with a tacking of clear and three full coats. I figure one coat is lost due to wet sanding and buffing.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-14-2020, 08:15 PM   #259
CaliforniaBorn36
Senior Member
 
CaliforniaBorn36's Avatar
 
Join Date: Oct 2012
Location: San Francisco Bay Area
Posts: 427
Default Re: Interest in new restoration project thread?

Love the color, in the mid 70's I had a 1/2 ton pickup that color with red pin striping. And, in light surface rust above the windshield you could see..."U.S. MAIL"
CaliforniaBorn36 is offline   Reply With Quote
Old 05-14-2020, 09:00 PM   #260
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Interest in new restoration project thread?

It must be nice to be able to pick which 1000 point restored '40 Ford coupe to drive just by the color!

In the real world, fantastic job. I can't wait to see the completed project.
tubman is online now   Reply With Quote
Old 05-14-2020, 09:13 PM   #261
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Interest in new restoration project thread?

That, is flathead Art! Prettier than a Picasso in my book.
RalphM is offline   Reply With Quote
Old 05-14-2020, 09:15 PM   #262
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by tubman View Post
It must be nice to be able to pick which 1000 point restored '40 Ford coupe to drive just by the color!

In the real world, fantastic job. I can't wait to see the completed project.
Drive? ARGGHH!!!!

Thanks Tubman...
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-15-2020, 03:48 PM   #263
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

You put it on a little heavier than I do. I stop at three coats but it's probably due to the rivets that are on a lot of my projects. Paint likes to sag around rivets. I'm well acquainted with nib files and fine sand paper these days. My hand isn't as steady as it used to be. I may have to try some Chromabase single stage sometime. I have used the Imron Elite but it's not the same as the old stuff. The Imron AF400 is getting too expensive. It's all Axalta stuff now.

I also use the Sherwin Williams Acry Glo stuff sometimes. It depends on what the customer wants.

The old 40 is lookin good.
rotorwrench is offline   Reply With Quote
Old 05-15-2020, 04:33 PM   #264
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

double post - Error
rotorwrench is offline   Reply With Quote
Old 05-28-2020, 08:19 AM   #265
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Good morning guys!
Finally have the body buffed out. I am eager to put it on the frame but will wait until I have the engine and exhaust in and running properly.
Once the body is down... look out!
I haven't finished a '39 or '40 in Folkstone in about fifteen years or so. I'm really enjoying the change of pace.
I believe the contrast between the (mostly) gloss black chassis and the gray floor pans will be a wonderful sight.
Attached Images
File Type: jpg P1050999.JPG (153.0 KB, 216 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-28-2020, 08:22 AM   #266
Seth Swoboda
Senior Member
 
Seth Swoboda's Avatar
 
Join Date: May 2010
Location: Southern Illinois
Posts: 3,744
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Looks really nice Kube.
Seth Swoboda is offline   Reply With Quote
Old 05-28-2020, 08:23 AM   #267
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Looking great!
DavidG is offline   Reply With Quote
Old 05-28-2020, 02:29 PM   #268
Shoebox
Senior Member
 
Shoebox's Avatar
 
Join Date: Jan 2014
Location: Holmen,Wisconsin
Posts: 772
Default Re: Interest in new restoration project thread?

Mike,
That is simply beautiful, as others have stated so well.
__________________
I went, I saw, I bought the T shirt

51 Ford Deluxe Tudor
32 Ford roadster
39 Mercury Towncar
Shoebox is offline   Reply With Quote
Old 07-06-2020, 09:19 PM   #269
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

No pressure Mike, but any updates? Hope it's all comin' along as planned.
Will D is offline   Reply With Quote
Old 07-06-2020, 10:17 PM   #270
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Will D View Post
No pressure Mike, but any updates? Hope it's all comin' along as planned.
Sorry... I am embarrassed to admit, but I kind of forgot all about this thread.

I'll try to update tomorrow.
Sorry
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-06-2020, 10:30 PM   #271
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Sorry... I am embarrassed to admit, but I kind of forgot all about this thread.

I'll try to update tomorrow.
Sorry
No worries, no need to apologize, it happens to the best of us the anticipation is killin' me tho
Will D is offline   Reply With Quote
Old 07-07-2020, 06:45 AM   #272
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Sorry... I am embarrassed to admit, but I kind of forgot all about this thread.

I'll try to update tomorrow.
Sorry
Mike, what spray gun do you like to use on the final finish material? ALSO can you speak to how you have your air supply line equipped?? Air Dryer? Desiccant Filters??? Picture maybe???



ALSO on the inside floor pans and bottom side how much wet sanding and buffing do you do on those? Same as the rest of the body??


KUBE, you and DAVIDG's restorations are the benchmark for sure. JUST Fabulous fabulous work!!! I am in complete awe!!!
rockfla is online now   Reply With Quote
Old 07-07-2020, 07:50 AM   #273
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by rockfla View Post
Mike, what spray gun do you like to use on the final finish material? ALSO can you speak to how you have your air supply line equipped?? Air Dryer? Desiccant Filters??? Picture maybe???
ALSO on the inside floor pans and bottom side how much wet sanding and buffing do you do on those? Same as the rest of the body??
KUBE, you and DAVIDG's restorations are the benchmark for sure. JUST Fabulous fabulous work!!! I am in complete awe!!!
Robert,
Use a Devillbiss gun. I'd have to check model number if you'd so desire.
Air dryer and water trap plus I have the lines routed at a downward slope along the rear wall of the spray area. Every four feet there is a lateral "trap"- a pipe that goes nearly to the floor with a levered drain valve at the bottom. There are four of these on the way to the end where I hook up for air supply.
Not my idea but one I found on the good ol' Web. It works wonderfully.
On the inside floors, inside fenders, inside hood, inside trunk lid, etc. all surfaces are prepared just like the top of the hood. So yep, same as the rest of the body.
Buffing? ALL painted surfaces are blocked after painting and buffed. The "inside" of the floor gets just a tad less IF the paint is laid down very well.
Attached Images
File Type: jpg floor rear aft.jpg (35.2 KB, 171 views)
File Type: jpg trk floor.jpg (49.3 KB, 176 views)
File Type: jpg conv.jpg (53.3 KB, 176 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-08-2020, 01:58 PM   #274
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sorry I haven't kept up to date with this thread.
The chassis is complete sans the engine. That will be back from the machine shop next week. I'll have it together quickly thereafter.
Then, I'll install the engine, transmission & exhaust system. Once that's running the way I like it, the body will go on the frame. It (body) is already painted & buffed. I prefer to be 100% certain all mechanical features are operating properly prior to doing the body drop.
I have perhaps 99% of the remaining parts to complete this restoration restored and cataloged for installation when their respective time comes.
I still have to upholster the seat back rest cushions.
The doors, hood and trunk lid are 100% ready to be painted. The front fenders require a bit more blocking but are very close.
The rear fenders have the metal work completed.
All the body parts have been fit to the body already so once the finish work is done, it's straight to paint.
I must admit, I am quite eager to drop the body
Attached Images
File Type: jpg 1.JPG (143.5 KB, 83 views)
File Type: jpg 11.JPG (147.0 KB, 82 views)
File Type: jpg 111.JPG (157.5 KB, 83 views)
File Type: jpg 1111.JPG (150.0 KB, 77 views)
File Type: jpg 11111.JPG (153.0 KB, 87 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-09-2020, 02:52 AM   #275
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

It's looking great, Mike. Thanks for laying out the thought process and planning behind the build.

Mart.
Mart is offline   Reply With Quote
Old 07-09-2020, 08:32 AM   #276
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Thank you Mike for keeping us all informed.
Your work is a pleasure to see.
19Fordy is offline   Reply With Quote
Old 07-12-2020, 07:53 PM   #277
funrunr
Senior Member
 
funrunr's Avatar
 
Join Date: May 2010
Location: Belleville,MI
Posts: 1,426
Default Re: Interest in new restoration project thread?

Thanks for bringing us along. I really enjoy looking at your work and progress.
__________________
Thank God
this is only a hobby!
funrunr is online now   Reply With Quote
Old 07-13-2020, 12:11 AM   #278
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Great stuff as always. No doubt on your consistency Mike. No doubt your rides drive as intended.

Last edited by Tinker; 07-13-2020 at 12:32 AM.
Tinker is offline   Reply With Quote
Old 07-13-2020, 05:52 AM   #279
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: Interest in new restoration project thread?

Beautiful work Mike and great fun to watch the progress! Thanks for taking the time to do the posts.


Gllenn
glennpm is online now   Reply With Quote
Old 08-09-2020, 09:36 AM   #280
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

FINALLY got the engine back from the machine shop last Sunday. They are good but painfully slow - 6 1/2 months slow.
I'm not one to sit around so in the meantime, other things have been getting done to further this project along.
I haven't been able to paint as I have the completed body (shell) in the paint area.
I hope to be able to drop the body on the chassis late this week.
Attached Images
File Type: jpg eng 8 9 20 (2).JPG (154.5 KB, 214 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-09-2020, 02:03 PM   #281
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Looking Good Kube! Was just thinking about you and this thread the order day, great to see another update.

I know what you mean about that wait at the machine shop. I just had my first experience with one last week. What I was told would be 3 days ended up being 2 weeks....was worth it tho knowing the guy does good work although slow.
Will D is offline   Reply With Quote
Old 08-09-2020, 02:17 PM   #282
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

Looks great, Mike. Really spotless.

Can i just ask people in general that if they ever look at my stuff, not to do it immediately after looking at Mike's stuff.

Thanks.
Mart is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-09-2020, 09:06 PM   #283
rattlesnakehoey
Member
 
Join Date: May 2010
Location: Downunder
Posts: 31
Default Re: Interest in new restoration project thread?

I am a big wrap for both you and Kube.
Keep the great posts coming fellas. Thumbs up from Downunder.
rattlesnakehoey is offline   Reply With Quote
Old 08-10-2020, 08:47 AM   #284
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Mart View Post
Looks great, Mike. Really spotless.

Can i just ask people in general that if they ever look at my stuff, not to do it immediately after looking at Mike's stuff.

Thanks.
You're hilarious!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-10-2020, 08:51 AM   #285
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: Interest in new restoration project thread?

I hear you Mart ;-)



Quote:
Originally Posted by rattlesnakehoey View Post
I am a big wrap for both you and Kube.
Keep the great posts coming fellas. Thumbs up from Downunder.
glennpm is online now   Reply With Quote
Old 08-10-2020, 07:59 PM   #286
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Mart View Post
Can i just ask people in general that if they ever look at my stuff, not to do it immediately after looking at Mike's stuff.

Thanks.
Promise
Zeke3 is online now   Reply With Quote
Old 08-12-2020, 02:11 PM   #287
garys34
Junior Member
 
Join Date: Jan 2019
Posts: 12
Default Re: Interest in new restoration project thread?

count me in...Gary G
garys34 is offline   Reply With Quote
Old 08-15-2020, 12:47 PM   #288
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Have the chassis prepared to drop the body next Monday. Earlier today, I was thinking back to the days when two of us could lift and place the body down. Those days are longggg gone
Monday, there will be four of us.
I used up my last remaining NOS exhaust system on this coupe.
Attached Images
File Type: jpg P1060178.jpg (32.4 KB, 274 views)
File Type: jpg P1060179.JPG (148.0 KB, 924 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-15-2020, 01:38 PM   #289
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

Gosh Mike, that's beautiful. A great example to all restorers.
19Fordy is offline   Reply With Quote
Old 08-15-2020, 02:11 PM   #290
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by 19Fordy View Post
Gosh Mike, that's beautiful. A great example to all restorers.
Thanks

Are there any restorers remaining?
I fear I am the last (or close to it) of a dying breed.
Makes me sad to realize our hobby is not what it once was.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-15-2020, 02:40 PM   #291
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

I really hope that's not two TINY little pits I'm seeing on that rear end! Otherwise, GORGEOUS...………….just like we've all come to expect out of any Kubarth restoration. DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 08-18-2020, 07:55 AM   #292
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

It's always a relief when the body is down and there were no mishaps along the way.
Next step? I'll get the doors painted (they're ready to shoot) so I can install them and bolt the body down.
Attached Images
File Type: jpg P1060185.jpg (50.6 KB, 208 views)
File Type: jpg P1060186.jpg (28.0 KB, 186 views)
File Type: jpg P1060188.jpg (50.1 KB, 205 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-18-2020, 08:28 AM   #293
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Nicely done Kube!
Will D is offline   Reply With Quote
Old 08-18-2020, 08:38 AM   #294
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Interest in new restoration project thread?

Incredible!
tubman is online now   Reply With Quote
Old 08-18-2020, 01:14 PM   #295
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Wow....Another brand new eighty-year-old Ford about to begin the trip all over again, leading the 'good' life this time around. Once again.....'Perfection' out of Kubarth Acres! Very soon now, you WILL be duplicating THIS picture below, correct? DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 08-18-2020, 06:14 PM   #296
TomT/Williamsburg
Senior Member
 
TomT/Williamsburg's Avatar
 
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,646
Default Re: Interest in new restoration project thread?

Mamma Mia you do stellar work, Mike!
TomT/Williamsburg is offline   Reply With Quote
Old 08-18-2020, 07:00 PM   #297
Ford46
Senior Member
 
Ford46's Avatar
 
Join Date: May 2010
Location: Southeastern, MA
Posts: 433
Default Re: Interest in new restoration project thread?

Just stunning Mike as usual!!!!
Ford46 is offline   Reply With Quote
Old 08-18-2020, 09:44 PM   #298
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Guys, thanks a ton for the nice comments. Truthfully, I'm never 100% happy with what I do and don't feel worthy of your affirmations.
I DO appreciate them - just don't feel worthy...
I love this hobby.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-19-2020, 01:20 PM   #299
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

You must love it Mike, it's obvious to anyone looking. I think you're doing a wonderful job. Certainly a level of quality I could never attain.
I'm heaping on the praise so you can question your worthiness more than normal.
Mart.
Mart is offline   Reply With Quote
Old 08-23-2020, 08:14 PM   #300
funrunr
Senior Member
 
funrunr's Avatar
 
Join Date: May 2010
Location: Belleville,MI
Posts: 1,426
Default Re: Interest in new restoration project thread?

I really appreciate your talent that you put forth into these cars. Your attention to detail is beyond any person I’ve ever met. You have a gift. Thanks for sharing.
__________________
Thank God
this is only a hobby!
funrunr is online now   Reply With Quote
Old 08-23-2020, 09:47 PM   #301
Lawson Cox
Senior Member
 
Lawson Cox's Avatar
 
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by jimalabam View Post
Cube: Proceed - I am never to old (82) to learn new information and/or techniques...
At 89 I'm still interested in the process but sadly I just can't do the physical work anymore. I'm looking forward to your progress.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes.

It is better to be seen, than viewed.

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".
Lawson Cox is offline   Reply With Quote
Old 08-27-2020, 07:18 PM   #302
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I keep moving forward. Bouncing around a little just to keep it fun.
Even though I have the patterns from Ford for the tool tray liners, it's still quite the task to install them neatly.

I'd painted a lot of "little" parts the other day. Grille louvers, trunk lid supports, hood hinges, etc. Also got the rear side of the doors painted. Tomorrow I'll paint the outside of the doors.
Once I get the doors sanded and polished, I'll hang them and adjust the body (pads) as might be necessary.
I always test fit everything at least once. I only place a thin piece of webbing between the frame and body when fitting. Once the body has been painted and polished, I install the correct pads between the body and frame.
With all the test fitting, I have yet to have a car go together without at least a tiny bit of shimming.
Attached Images
File Type: jpg tool tray aft.jpg (32.8 KB, 175 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-29-2020, 09:22 AM   #303
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Smile Re: Interest in new restoration project thread?

Looking at the underside of that car, I can see why you would never want to drive them!
RalphM is offline   Reply With Quote
Old 08-29-2020, 10:30 AM   #304
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Interest in new restoration project thread?

They certainly don't stay in like new condition without taking the steps to preserve them that way. It isn't often that any car gets to start over like this. An easy button is not in the picture for full on restorations. I sure wish it was but wishing doesn't get the job done.
rotorwrench is offline   Reply With Quote
Old 09-01-2020, 08:26 AM   #305
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
I keep moving forward. Bouncing around a little just to keep it fun.
Even though I have the patterns from Ford for the tool tray liners, it's still quite the task to install them neatly.

I'd painted a lot of "little" parts the other day. Grille louvers, trunk lid supports, hood hinges, etc. Also got the rear side of the doors painted. Tomorrow I'll paint the outside of the doors.
Once I get the doors sanded and polished, I'll hang them and adjust the body (pads) as might be necessary.
I always test fit everything at least once. I only place a thin piece of webbing between the frame and body when fitting. Once the body has been painted and polished, I install the correct pads between the body and frame.
With all the test fitting, I have yet to have a car go together without at least a tiny bit of shimming.
It might be a stupid question here Mike BUT are you shimming to achieve "Gap" integrity?? AND even after all of your test fitting you still find on most project you still have to shim??
rockfla is online now   Reply With Quote
Old 09-01-2020, 11:18 AM   #306
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by rockfla View Post
It might be a stupid question here Mike BUT are you shimming to achieve "Gap" integrity?? AND even after all of your test fitting you still find on most project you still have to shim??
Not a stupid question whatsoever.
Rarely is it necessary to actually shim to achieve the final (acceptable) gaps. Typically I may have to pull one mounting bolt down a bit more or back one off.
I have had to (frequently) scrape paint away from the back of a door hinge(s) where it fastened to body.
Hard to believe even after all of these projects that the paint thickness can make a difference in the gap.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 09-01-2020, 12:33 PM   #307
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Hard to believe even after all of these projects that the paint thickness can make a difference in the gap.

Interesting subject! Paint can cause several points of consideration in an automobile, like what Kube states above. Many of us have found-out the hard way that paint can insulate electrical GROUND circuits or surfaces. And interestingly, depending on how much painted surface, and how many coats and what types have been applied to such, you can end-up adding some noticeable weight to a vehicle. It's not unheard of, depending on paint scheme, for some of the largest wide-body airline type aircraft to end-up with over a thousand pounds of paint being applied to one airplane. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 09-06-2020, 05:44 PM   #308
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Kind of been "bouncing around" on this project in the past week or so.
I did manage to get the inside of the rear fenders painted and plan on shooting the outside on Tuesday. Doors are painted on both sides and the hood only needs to be tacked and squirted.
Got a lot of the engine built up.
Once the rear fenders are painted, I'll buff the doors and fenders and hang the doors.
Attached Images
File Type: jpg P1060202.jpg (68.2 KB, 630 views)
File Type: jpg P1060203.jpg (82.4 KB, 153 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 09-06-2020, 06:39 PM   #309
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

.

NICE, Kubarth! And look at that nice clean, shiny GROUNDING surface for the starter on the painted oil pan....just one of a bazillion details NOT to be overlooked. Looks like another one knocked "out of the park" from Kube Acres. Just beautiful!! DD

__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 09-06-2020, 07:54 PM   #310
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
.

NICE, Kubarth! And look at that nice clean, shiny GROUNDING surface for the starter on the painted oil pan....just one of a bazillion details NOT to be overlooked. Looks like another one knocked "out of the park" from Kube Acres. Just beautiful!! DD

Thanks Coopman,
This one has been fun for the most part. I've never done a Folkstone Gray coupe before.
As soon as this one is near completion, I'll be starting on another '40 convertible.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-07-2020, 07:47 PM   #311
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Hey, it's been about eight weeks since I'd posted on this thread. Nope, the restoration has not been completed. However, I've made a lot of progress.
Headliner is in, trunk is trimmed out, rear 'seating area" is nearly trimmed. Oh, all the painting is done except the trunk lid.
I wasn't quite happy with the way the lid fit so welded up both sides (vertical edges) adding about 1/8" to the lip on each side. I'm glad in retrospect i took the time as the lid now fits beautifully. The latch catches under the weight of the lid alone.
Attached Images
File Type: jpg 1.jpg (72.4 KB, 175 views)
File Type: jpg 2.JPG (155.0 KB, 179 views)
File Type: jpg 3.JPG (159.0 KB, 178 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-08-2020, 02:24 AM   #312
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Coming along nicely.
Will D is offline   Reply With Quote
Old 11-08-2020, 03:49 AM   #313
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

I can't believe I'm allowed on the same forum.
Mart is offline   Reply With Quote
Old 11-08-2020, 07:35 AM   #314
rufus39
Senior Member
 
rufus39's Avatar
 
Join Date: Jun 2012
Location: North Georgia
Posts: 111
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Mart View Post
I can't believe I'm allowed on the same forum.
. Me too !!! Mike, Sheeza lookin mighty fine !
rufus39 is offline   Reply With Quote
Old 11-09-2020, 12:01 AM   #315
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Looks like a nice solid floor to start with. Great stuff Mike!
Tinker is offline   Reply With Quote
Old 11-09-2020, 08:30 AM   #316
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Tinker View Post
Looks like a nice solid floor to start with. Great stuff Mike!
Look closer at the "before" photo and you'll note the entire thing (floor) had been cut apart and welded (with a coat hanger I believe).
Attached Images
File Type: jpg P1050263.jpg (72.9 KB, 118 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-09-2020, 09:33 AM   #317
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Kube, so did you cut the panels out and TIG or MIG weld the panels back in or replace the whole floor? Also, when you added material for the trunk lid edge, what process did you use? I have a lot of rust repair on my '37 to tackle. I am trying to build up my skills on items that will not be visible before I attempt the more obvious areas.

Thanks for the great photos.
Zeke3 is online now   Reply With Quote
Old 11-09-2020, 05:15 PM   #318
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
Kube, so did you cut the panels out and TIG or MIG weld the panels back in or replace the whole floor? Also, when you added material for the trunk lid edge, what process did you use? I have a lot of rust repair on my '37 to tackle. I am trying to build up my skills on items that will not be visible before I attempt the more obvious areas.

Thanks for the great photos.
Hey Zeke,
I do cut out as much of the floor as necessary. The front section (floor) of this car was pretty decent so I left it in and repaired as necessary. A lot of bumping and filing but little rust to deal with.
This car had a decent tail pan - decent. However, as I had to do a LOT of work on the trunk floor as well as the auxiliary seat area floor, it (tail pan with trunk pan) was replaced.

The pan beneath the auxiliary seat area is not reproduced and as such, that took a lot of effort to make it as new once again. A number of new pieces were fabricated.
I MIG all of the sheet metal. Slowly of course, an inch or so here and then and inch or so "over there". I allow plenty of time for each are to cool back to room temperature prior to going any further with the welding.
I butt weld where the pan requires (as authentic) a one piece appearance. There are a couple of lap joint welds on some of these cars. When one is encountered, I mimic that.
Welding the edge of a trunk lid is easy but very time consuming. Here too, I MIG. Once I believe I am done, I'll grind the newly placed welds down and occasionally need to add more in a spot or three.

Hope this helps...
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-09-2020, 05:42 PM   #319
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: Interest in new restoration project thread?

Kube,

Was your carburetor done by Charlie ny, or did you restore it ? Were they that natural color originally ? I ask, because I've seen some later NOS Holley two barrel carbs from '55 and '56 that had been di-chromated a pale green'ish color.

Thanks, Sal
scicala is offline   Reply With Quote
Old 11-09-2020, 06:05 PM   #320
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Kube, that is a big help. I have been trying to butt weld my patches in with a 110v MIG machine. I usually go one spot at a time and jump around to allow the welds to cool. Lately I have been having more problems with blowing a hole in the base metal, even with the welder set as low as it will go. Then I end up with a mess trying to fill the hole.

Every little bit of information helps, thanks.
Zeke3 is online now   Reply With Quote
Old 11-09-2020, 06:42 PM   #321
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by scicala View Post
Kube,

Was your carburetor done by Charlie ny, or did you restore it ? Were they that natural color originally ? I ask, because I've seen some later NOS Holley two barrel carbs from '55 and '56 that had been di-chromated a pale green'ish color.

Thanks, Sal
Sal, I do have Charlie build my carbs. The one on this car was NOS but obviously still needed a rebuild. I mention that as the "color" is stock.
The authentic plating for 1939 - 1940 was pretty much what you see on this car. However, as you know better than most, there were slight variations. I've seen some NOS carbs that has a slight pinkish tint and others a slight bluish tint.
Perhaps what I see as bluish, you see as greenish.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-09-2020, 06:44 PM   #322
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
Kube, that is a big help. I have been trying to butt weld my patches in with a 110v MIG machine. I usually go one spot at a time and jump around to allow the welds to cool. Lately I have been having more problems with blowing a hole in the base metal, even with the welder set as low as it will go. Then I end up with a mess trying to fill the hole.

Every little bit of information helps, thanks.
Heck, don't get discouraged. As long as I've been doing this I still occasionally will blow a hole through some sheet metal.
What size wire are you using?
Oxygen tank? Argon?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-09-2020, 10:07 PM   #323
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

I am using 0.023" wire with Argon/CO2 mix.
Zeke3 is online now   Reply With Quote
Old 11-10-2020, 11:06 AM   #324
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Sal, I do have Charlie build my carbs. The one on this car was NOS but obviously still needed a rebuild. I mention that as the "color" is stock.
The authentic plating for 1939 - 1940 was pretty much what you see on this car. However, as you know better than most, there were slight variations. I've seen some NOS carbs that has a slight pinkish tint and others a slight bluish tint.
Perhaps what I see as bluish, you see as greenish.
Thank you for the reply. That helps a lot.

Sal
scicala is offline   Reply With Quote
Old 11-10-2020, 01:33 PM   #325
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Hey Kube


Do you do the interiors NOW that LB is no longer???
rockfla is online now   Reply With Quote
Old 11-10-2020, 01:42 PM   #326
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by rockfla View Post
Hey Kube


Do you do the interiors NOW that LB is no longer???
Nope, not yet anyway.
I bought a few interior kits from LB about a year before they announced their impending implosion.
Not certain how many more restorations I'll be doing. Of course I was saying that 12 - 14 cars ago
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-11-2020, 01:25 PM   #327
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

A little more progress that without a fellow Barn member (Mike D.) I am not so certain I could have accomplished.
Thanks Mike D.
Attached Images
File Type: jpg rear seat aft.JPG (155.0 KB, 219 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-13-2020, 02:25 AM   #328
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Kube View Post
Look closer at the "before" photo and you'll note the entire thing (floor) had been cut apart and welded (with a coat hanger I believe).

But there was a floor to start with. You always do great top knotch work. Wasn't a dig.
Tinker is offline   Reply With Quote
Old 11-13-2020, 09:01 AM   #329
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Interest in new restoration project thread?

Mike, thanks for the shout out! Was more then happy to assist you with some information and measurements.
Mike D. aka deuce_roadster.
deuce_roadster is offline   Reply With Quote
Old 12-02-2020, 12:19 PM   #330
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Here's why I prefer to paint the cars in color... I really enjoy the contrast, especially beneath the car.
Attached Images
File Type: jpg P1060341.JPG (156.5 KB, 223 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-02-2020, 08:52 PM   #331
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

I can see your point on the contrast between the chassis and the body.
Zeke3 is online now   Reply With Quote
Old 12-05-2020, 08:35 PM   #332
fordor
Member
 
Join Date: May 2010
Location: Michigan
Posts: 87
Default Re: Interest in new restoration project thread?

Is the tool tray lined with the same material used to insulate the inside of the trunk lid on a 40? If so, do you have a picture of a completed tool tray area?
Thanks,
Bob L.
fordor is offline   Reply With Quote
Old 12-05-2020, 08:51 PM   #333
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by fordor View Post
Is the tool tray lined with the same material used to insulate the inside of the trunk lid on a 40? If so, do you have a picture of a completed tool tray area?
Thanks,
Bob L.
Yes sir, the same material. The photo attached is from a '39 coupe I'd restored. Same as a '40 in this regard.
Attached Images
File Type: jpg tool tray aft.JPG (61.9 KB, 163 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-05-2020, 08:54 PM   #334
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by fordor View Post
Is the tool tray lined with the same material used to insulate the inside of the trunk lid on a 40? If so, do you have a picture of a completed tool tray area?
Thanks,
Bob L.
Bob, Here's a couple from this particular car.
Attached Images
File Type: jpg P1060200.jpg (41.1 KB, 155 views)
File Type: jpg tool tray aft.jpg (33.0 KB, 145 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-08-2020, 12:07 PM   #335
fordor
Member
 
Join Date: May 2010
Location: Michigan
Posts: 87
Default Re: Interest in new restoration project thread?

Thanks, that's what I was looking for. By the way, great restoration. I appreciate you sharing the process with everyone, its great.
fordor is offline   Reply With Quote
Old 12-10-2020, 05:20 PM   #336
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Working on two restorations now so the progress on the coupe has slowed a bit. I did manage to get both doors installed. Latches, weather-strips, etc. all in and fit well.
Got the trunk lid installed today along with the associated pieces.
Welded the vertical sides up perhaps 3/16". Looks so much better than the factory fit in relation to the body. Very time consuming but worth the effort in my opinion.
Attached Images
File Type: jpg P1060409.JPG (150.0 KB, 115 views)
File Type: jpg P1060408.JPG (156.0 KB, 372 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-10-2020, 06:02 PM   #337
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: Interest in new restoration project thread?

.

For the rest of us mere mortals, try to imagine how Mike gets that brand new black insulation material between the stamped bracing and the outer skin.....wrinkle-free, no less! I'll say it again....the guy is an ANIMAL! DD

__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 12-11-2020, 09:48 AM   #338
funrunr
Senior Member
 
funrunr's Avatar
 
Join Date: May 2010
Location: Belleville,MI
Posts: 1,426
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by V8COOPMAN View Post
.

For the rest of us mere mortals, try to imagine how Mike gets that brand new black insulation material between the stamped bracing and the outer skin.....wrinkle-free, no less! I'll say it again....the guy is an ANIMAL! DD

Yes, how is that done? I have the new material but couldn't figure out how to install without cutting into a million pieces.
Beautiful work Mike.
__________________
Thank God
this is only a hobby!
funrunr is online now   Reply With Quote
Old 12-11-2020, 10:18 AM   #339
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by funrunr View Post
Yes, how is that done? I have the new material but couldn't figure out how to install without cutting into a million pieces.
Beautiful work Mike.
Not as difficult as it may appear. When I have the inner structure removed from the outer lid, I install the "paper". I back tape (mask) it for later painting purposes.
Keep in mind this part is most certainly over restoring. Ford, like myself, placed the insulation between the inner and outer structures. However, Ford did not mask the paper. They painted right over it. Over the years much of the authentic paint was absorbed and / or simply flaked off.

The difficult part (not too bad really) is splicing the insulation where it (seams) can't be detected.
Drake reproduces this insulation - it is VERY nice. However, in this instance, the repop stuff isn't wide enough and thus, must be spliced.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-11-2020, 10:42 AM   #340
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Thanks Kube, I hadn't thought about removing the inner structure from the outer structure of the trunk lid. My 37 trunk lid will need some repairs, due to earlier modifications by a previous owner and a little rust. Are the two attached by spot welds around the edge?
Zeke3 is online now   Reply With Quote
Old 12-11-2020, 11:14 AM   #341
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
Thanks Kube, I hadn't thought about removing the inner structure from the outer structure of the trunk lid. My 37 trunk lid will need some repairs, due to earlier modifications by a previous owner and a little rust. Are the two attached by spot welds around the edge?
This is not as easy as simply removing welds as the outer structure is formed over the inner. I grind away the edge on three sides and remove the inner that way. There are a few (many) cuss words spoken beneath my breath while doing this. As I tend to weld up the edges of the lid to fit the body as perfectly as possible, well, grinding away that edge is no big deal for me.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-11-2020, 01:58 PM   #342
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Wow, not for the faint of heart. Do you use filler metal to create a new edge then? I remember from one of your earlier posts that you reworked the trunk lid to make them fit better. With apologies to Paul Harvey, now for the rest of the story...

Thanks for taking us along on this project, beautiful work.
Zeke3 is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-11-2020, 03:29 PM   #343
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Zeke3 View Post
Wow, not for the faint of heart. Do you use filler metal to create a new edge then? I remember from one of your earlier posts that you reworked the trunk lid to make them fit better. With apologies to Paul Harvey, now for the rest of the story...

Thanks for taking us along on this project, beautiful work.
Nope... I weld the entire edge. That's not difficult but very time consuming.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-11-2020, 05:24 PM   #344
37fatfender
Senior Member
 
37fatfender's Avatar
 
Join Date: May 2010
Location: Mesquite, NV / Gurnee, IL
Posts: 298
Default Re: Interest in new restoration project thread?

I'm honored to tell everyone even though its under the car and can't be seem "Kube" restored my Columbia!
37fatfender is offline   Reply With Quote
Old 12-15-2020, 08:25 PM   #345
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I've had a few guys ask me what I use for sound deadening, etc. I have always used the foil lined insulation available at any decent builder supply house. Very economical, holds up extremely well and is easy to install.
I also install a moisture barrier on the doors. I was taught to do this by an "old timer" that owned and operated an upholstery shop for better than fifty years.
The barrier is most likely not necessary, especially considering these cars rarely, if ever get driven and certainly not in rain!

Still, can't hurt...
Attached Images
File Type: jpg before barrier.jpg (32.3 KB, 188 views)
File Type: jpg after barrier (1).jpg (28.1 KB, 180 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 12-15-2020, 08:31 PM   #346
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Kube View Post
I've had a few guys ask me what I use for sound deadening, etc. I have always used the foil lined insulation available at any decent builder supply house. Very economical, holds up extremely well and is easy to install.
I also install a moisture barrier on the doors. I was taught to do this by an "old timer" that owned and operated an upholstery shop for better than fifty years.
The barrier is most likely not necessary, especially considering these cars rarely, if ever get driven and certainly not in rain!

Still, can't hurt...
Do you put a couple layers or just one piece?
Will D is offline   Reply With Quote
Old 12-16-2020, 12:53 AM   #347
restoman
Member
 
Join Date: May 2010
Location: near san diego
Posts: 88
Default Re: Interest in new restoration project thread?

Hi Mike,

Sounds like a year of good information and methods. I would enjoy it for sure,,,,,,,,,PHIL
restoman is offline   Reply With Quote
Old 12-16-2020, 08:55 AM   #348
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by Will D View Post
Do you put a couple layers or just one piece?
Just one piece. It's fairly thick.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 03-31-2021, 05:59 PM   #349
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

I have been so very negligent in keeping up with this thread. For that I apologize.
Seems that life (in general) and restoring another '40 convertible simultaneously with this coupe also kinda gets in the way.

Anyways, the coupe is coming along nicely. And, although I've stated this in the past, I'm gonna do it again... I really prefer colored bodies vs. black as the detail found in the contrast just makes me smile.
Attached Images
File Type: jpg P1060715.jpg (21.3 KB, 169 views)
File Type: jpg P1060716.JPG (160.5 KB, 165 views)
File Type: jpg P1060720.JPG (151.5 KB, 159 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 03-31-2021, 06:19 PM   #350
rufus39
Senior Member
 
rufus39's Avatar
 
Join Date: Jun 2012
Location: North Georgia
Posts: 111
Default Re: Interest in new restoration project thread?

Mike, as usual, first rate stuff you are doing. It's looking great !
rufus39 is offline   Reply With Quote
Old 04-01-2021, 06:54 AM   #351
fortyfords
Senior Member
 
fortyfords's Avatar
 
Join Date: Mar 2011
Location: faucett, mo
Posts: 419
Default Re: Interest in new restoration project thread?

Definitely always great to see guys who want to keep 40's alive and I appreciate being able to see more of the one car I really love on the road. My hat's off to you and your fine work. It must be exhausting finding parts to restore one. Nothing prettier than 32 and 40 Fords.
fortyfords is offline   Reply With Quote
Old 04-13-2021, 02:39 PM   #352
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Little by little.
Attached Images
File Type: jpg P1060739.JPG (154.5 KB, 135 views)
File Type: jpg P1060742.JPG (152.5 KB, 121 views)
File Type: jpg P1060743.JPG (157.0 KB, 116 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-13-2021, 03:00 PM   #353
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Thanks for the bench mark photos Mike, How do you keep your fastener finishes from getting marred up??? Do you tape your screwdriver ends, box ends???



Thanks in advanced
Rockfla
rockfla is online now   Reply With Quote
Old 04-13-2021, 04:20 PM   #354
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: Interest in new restoration project thread?

Looking good! I sure do like the contrasting colors, both on the underside of the car and fasteners; looks sharp.
__________________
Sometimes, ingenuity gets in the way of sense and sanity.
Will D is offline   Reply With Quote
Old 04-13-2021, 04:52 PM   #355
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Robert,


I only use six point sockets and box wrenches and only new or near new screw drivers. Perhaps Mike does something similar. I also spray all of the S2 finish fasteners with silicone before installing them to inhibit oxidation.
DavidG is offline   Reply With Quote
Old 04-13-2021, 05:58 PM   #356
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Robert,


I only use six point sockets and box wrenches and only new or near new screw drivers. Perhaps Mike does something similar. I also spray all of the S2 finish fasteners with silicone before installing them to inhibit oxidation.
Dave, Ya beat me to a response. Of course you being younger and faster surely helped.
Like you, I use six point sockets and box wrenches whenever possible. Screw drivers get tossed or turned in to an alignment tool as soon as the blade wears.
I apply a light coat of satin black to my S2 stuff.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-13-2021, 06:39 PM   #357
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Interest in new restoration project thread?

A always, I am very impressed with your work.

You have set a standard that most should aspire to.
tubman is online now   Reply With Quote
Old 04-14-2021, 06:49 PM   #358
Trojan
Junior Member
 
Join Date: Jun 2012
Location: Thousand Oaks, Ca.
Posts: 11
Default Re: Interest in new restoration project thread?

I'm in ! Looking forward to it.
Trojan is offline   Reply With Quote
Old 04-24-2021, 09:52 AM   #359
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Managed to get the hood on and aligned yesterday. More baby steps...
Attached Images
File Type: jpg P1060775.JPG (142.0 KB, 251 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-07-2021, 01:49 PM   #360
mickey1099
Junior Member
 
Join Date: Nov 2013
Posts: 19
Default Re: Interest in new restoration project thread?

Mike:
I lost your e-mail address & phone no. We met at Charlotte NC at the 75th
Ford Show! would love to chat wen you have time!
mickey25381
e-mail: [email protected]
phone: (276) 252-4650
Health has improved and want to finish my 40 project'
Thanks for the new Book
mickey1099 is offline   Reply With Quote
Old 07-30-2022, 09:10 AM   #361
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Guys, I am embarrassed to admit that I kinda forgot all about this thread.
The project has been completed. Here's a few photos of the final result.
Attached Images
File Type: jpg P1100574.JPG (153.5 KB, 109 views)
File Type: jpg P1100590.JPG (154.5 KB, 103 views)
File Type: jpg P1100601.JPG (165.0 KB, 104 views)
File Type: jpg P1100604.JPG (149.5 KB, 103 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-30-2022, 09:17 AM   #362
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
Default Re: Interest in new restoration project thread?

Mike,


Better than new; simply stunning!
DavidG is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-30-2022, 09:43 AM   #363
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: Interest in new restoration project thread?

Quote:
Originally Posted by DavidG View Post
Mike,


Better than new; simply stunning!
Thanks David. That truly means a LOT coming from you
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 07-30-2022, 10:53 AM   #364
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Interest in new restoration project thread?

WOWIE! Mike, stunning and beautiful.
It's always a pleasure to see your restorations. Your dedication to excellence shows.
Well done, for sure.
JIM
19Fordy is offline   Reply With Quote
Old 07-30-2022, 01:20 PM   #365
Zeke3
Senior Member
 
Zeke3's Avatar
 
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
Default Re: Interest in new restoration project thread?

Kube, thanks for bringing up this thread again, that is a beautiful car as the others have already noted. Now, I guess, I will have to go through this entire discussion to review the process again.
Zeke3 is online now   Reply With Quote
Old 07-30-2022, 03:54 PM   #366
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: Interest in new restoration project thread?

Sponsored Links (Register now to hide all advertisements)
Typed letters and or words somehow don’t convey…..what DavidG said x3. Mike I only hope I can produce something close one day. Congratulations on completion of this coupe.
rockfla is online now   Reply With Quote
Old 07-30-2022, 05:18 PM   #367
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Interest in new restoration project thread?

It's ok, I guess.

Ha ha no, Mike, it looks fantastic and it's a credit to you and reflects all the hard work you have put in.

I love that the barn supports all the different levels of the early Ford hobby.

Mike's perfection and my kludgery.

Mart.
Mart is offline   Reply With Quote
Old 07-30-2022, 05:45 PM   #368
fortyfords
Senior Member
 
fortyfords's Avatar
 
Join Date: Mar 2011
Location: faucett, mo
Posts: 419
Default Re: Interest in new restoration project thread?

Great job, I can't imagine finding all the correct colors and parts to do a job like that.
fortyfords is offline   Reply With Quote
Old 07-31-2022, 09:49 AM   #369
Fred A
Senior Member
 
Fred A's Avatar
 
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
Default Re: Interest in new restoration project thread?

Every additional view in Folkestone Gray highlights the dark details that many of us need to know. Black on black is tough by comparison. I'm off to a difficult start as the extent of cadmium in a word buried in second rate zinc is not understood in time. Grateful Kube shared again. Fred A
Fred A is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:49 AM.