The Ford Barn

d_Seymour · 06-24-2015, 05:29 AM

Good Day,
have a question regarding using a 32 front axles assembly on a model a.
Would I need to replace the 32 King pins with model A king pins in order to stay with the model A brake actuator rods setup.The 32 actuators angle in towards the center of the car.

kelley's restoration · 06-24-2015, 06:24 AM

you'll have to replace both the king pins and actuatorsalso need a spacer for the wishbone
tk

26Tguy · 06-24-2015, 07:00 AM

EDIT : incorrect info removed so as not to confuse anyone. Sorry

1928Fordman · 06-24-2015, 07:22 AM

32 Ford axles are 2" wide at the spring perch boss and model a's are 2 1/4".

d_Seymour · 06-24-2015, 07:05 PM

Thanks Kelley
I have model a components, Should the perch pins also be changed. I can remember a tech Post with great pc's but I can not find it. The post was really detailed, as I recall it was a couple of years ago.

Bob C · 06-24-2015, 07:37 PM

Sponsored Links (Register now to hide all advertisements)

Yes you need 32-34 spring perch, I got new ones from Bob Drake
hope they hold up.
Check this thread. http://www.fordbarn.com/forum/showth...light=lowering

Bob

COOTER · 06-25-2015, 09:20 AM

I just attempted to do this swap but using Model A spindles. Before full lock, the tie rod hits the crossmember...even if I drop the steering arms. Assuming you are using '32 spindles, let me know if it works out for you.

06-24-2015, 05:29 AM	#1
d_Seymour Junior Member Join Date: May 2010 Location: West Michigan Posts: 26	32 front axle assembly Good Day, have a question regarding using a 32 front axles assembly on a model a. Would I need to replace the 32 King pins with model A king pins in order to stay with the model A brake actuator rods setup.The 32 actuators angle in towards the center of the car.

06-24-2015, 06:24 AM	#2
kelley's restoration Senior Member Join Date: May 2010 Location: 60046 Posts: 888	Re: 32 front axle assembly you'll have to replace both the king pins and actuatorsalso need a spacer for the wishbone tk __________________ anyone need some Model A restoration work done in Illinois? shoot me an email for pics and information [email protected]

06-24-2015, 07:00 AM	#3
26Tguy Member Join Date: May 2010 Location: Manvel, TX Posts: 53	Re: 32 front axle assembly EDIT : incorrect info removed so as not to confuse anyone. Sorry Last edited by 26Tguy; 06-24-2015 at 09:23 AM.

06-24-2015, 07:22 AM	#4
1928Fordman Member Join Date: May 2010 Location: Kingwood, TX Posts: 84	Re: 32 front axle assembly 32 Ford axles are 2" wide at the spring perch boss and model a's are 2 1/4".

06-24-2015, 07:05 PM	#5
d_Seymour Junior Member Join Date: May 2010 Location: West Michigan Posts: 26	Re: 32 front axle assembly Thanks Kelley I have model a components, Should the perch pins also be changed. I can remember a tech Post with great pc's but I can not find it. The post was really detailed, as I recall it was a couple of years ago.

06-24-2015, 07:37 PM	#6
Bob C Senior Member Join Date: May 2010 Location: So Cal Posts: 8,748	Re: 32 front axle assembly Sponsored Links (Register now to hide all advertisements) Yes you need 32-34 spring perch, I got new ones from Bob Drake hope they hold up. Check this thread. http://www.fordbarn.com/forum/showth...light=lowering Bob Last edited by Bob C; 06-24-2015 at 07:42 PM.

06-25-2015, 09:20 AM	#7
COOTER Senior Member Join Date: May 2010 Location: Ontario, CA Posts: 187	Re: 32 front axle assembly I just attempted to do this swap but using Model A spindles. Before full lock, the tie rod hits the crossmember...even if I drop the steering arms. Assuming you are using '32 spindles, let me know if it works out for you.