|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-10-2014, 04:44 PM | #1 |
Senior Member
Join Date: Sep 2010
Location: Denmark
Posts: 330
|
Drill for Carburators
Hi..
Can anybody help me locate this " Drill Stand " , i will try to make a fine carburator for my TC... |
02-10-2014, 05:00 PM | #2 |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: Drill for Carburators
This one? 20 HSS bits, #61 through #80 with stand.
Available in the USA through Amazon.com LINK You will also need a pin chuck to use them. |
Sponsored Links (Register now to hide all advertisements) |
|
02-10-2014, 05:27 PM | #3 |
Senior Member
Join Date: Sep 2010
Location: michigan
Posts: 1,126
|
Re: Drill for Carburators
I got my drill bits for sizing jets from a hobby store hope this helps ps they also sell a little handle sepratly
|
02-10-2014, 05:31 PM | #4 | |
Senior Member
Join Date: Sep 2010
Location: Denmark
Posts: 330
|
Re: Drill for Carburators
Quote:
Mike K... Thank you, the ordre is send... ! Per |
|
02-10-2014, 05:43 PM | #5 |
Senior Member
Join Date: Aug 2010
Location: Port Orchard, WA
Posts: 1,498
|
Re: Drill for Carburators
I get mine from the bitlady.com in Canada, $12 CA plus shipping
5424 Monkey Tree Lane Sechelt, British Columbia V0N 3A2 Canada Telephone: 604 885-5854 http://bitlady.com/rootMicro_Number.html
__________________
1931 160B & 1931 68B If you don't have time to do it right the 1st time, how do you have time to do it the 2nd time? |
02-10-2014, 05:59 PM | #6 |
Senior Member
Join Date: Jun 2010
Location: Perry OH
Posts: 1,330
|
Re: Drill for Carburators
Sponsored Links (Register now to hide all advertisements)
|
02-10-2014, 06:03 PM | #7 |
Senior Member
Join Date: Jun 2010
Location: Perry OH
Posts: 1,330
|
Re: Drill for Carburators
How did you get that picture to load on this site ?
|
02-10-2014, 06:53 PM | #8 |
Senior Member
Join Date: Sep 2011
Location: Alton, NH
Posts: 1,231
|
Re: Drill for Carburators
You may already know this, but small bit must be used in a hand (pin) chuck, or used in a machine, such as a lathe or mill. Using them in an electric drill or a Dremel is a sure bet to break them.
__________________
It's not what people think they know that will hurt them, it is what they think they know that aint so! -Mark Twain. It is the very things that we think we know, that keep us from learning what we should know.- Unknown |
02-11-2014, 02:31 AM | #9 |
Senior Member
Join Date: Sep 2010
Location: Denmark
Posts: 330
|
Re: Drill for Carburators
Hi Jimvette...
I use this side. http://imageshack.us/content_round.p...illeder074.jpg if you will reg you there, it is ready for use... Make you tekst in Fordbarn, and there after , click on the " direkte " link on image shark.. so it´s Works.. Per, |
|
|
Sponsored Links (Register now to hide all advertisements) |
|