|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-20-2015, 12:22 PM | #1 |
Senior Member
Join Date: Sep 2011
Location: Livermore, CA
Posts: 124
|
Fuel line shield to prevent vapor lock?
My '29 was in a St. Patrick's Day parade the other day, and it was warmer than usual. I had an unusual problem surface, that is, my car exhibited signs of vapor lock, which has never happened before. I've ruled-out any other possible fuel-delivery problems, and am now looking for a way to counter having any other slow-speed (crawling) parade issues in the coming summer months.
A member of our car club says this can be a common problem with fully-stock Model A's, and that he's seen at least one vendor out there that markets some type of small heat shield that clamps-on to the fuel line, to at least give it a little added protection from the nearby exhaust manifold. However, I've so far been unable to locate any such product out there. Does anyone know of a vendor who sells something along these lines? Or, have any other ideas about how to shield the line from excess ambient temps during events such as parades? I read that some people have slit a rubber fuel line and placed it over their metal fuel lines; I'm wondering how successful that simple approach might be? |
03-20-2015, 12:44 PM | #2 |
Senior Member
Join Date: Jun 2014
Location: Rocklin, CA
Posts: 779
|
Re: Fuel line shield to prevent vapor lock?
On our long trips we found people running Marvel Mystery Oil or just ATF in the gas avoided vapor locking. You don't need a whole lot but it works.
|
Sponsored Links (Register now to hide all advertisements) |
|
03-20-2015, 02:00 PM | #3 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Fuel line shield to prevent vapor lock?
There have been some fuel lines I've seen where the horizontal section wasn't. They where pitched up toward the carburetor and I just 'adjust' the line so it is pitched down.
There has been some talk regarding poor grounding and that the fuel line may be acting as a ground possibly causing the problem. I have made light shields that bolt to the intake/exhaust retainer bolt and the muffler/pipe clamp. This shield is wider than the manifold and extends from near the carb flange to the muffler. The purpose is more to keep hot manifold air from away from the carb inlet. I just paint them to keep them as inconspicuous as possible. Over the years I've tried most of the tricks to try and eliminate this issue on many other type cars that really do have vapor lock issues with varied results. I also like the AFT suggestion. I like to use AFT in the fuel of old and not that often used engines. |
03-20-2015, 02:01 PM | #4 |
Senior Member
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
|
Re: Fuel line shield to prevent vapor lock?
The best thing I have found is a foam beer can cooler. Slip it over the sediment bowl and run 20 degrees cooler.
|
03-20-2015, 02:02 PM | #5 |
Senior Member
Join Date: Mar 2014
Location: Midland Park,N.J.
Posts: 1,108
|
Re: Fuel line shield to prevent vapor lock?
gas with ethanol sometimes will cause a problem try a cup of atf to a full tank of gas.
|
03-20-2015, 02:03 PM | #6 |
Senior Member
Join Date: Jun 2014
Location: Rocklin, CA
Posts: 779
|
Re: Fuel line shield to prevent vapor lock?
Sponsored Links (Register now to hide all advertisements)
|
03-20-2015, 02:46 PM | #7 |
Senior Member
Join Date: Mar 2011
Location: San Diego, CA
Posts: 149
|
Re: Fuel line shield to prevent vapor lock?
Bob,
I had some issues with my F100 Y-Block. I went to a speed shop/racing supply. They have several types of heat wrap, tube, tape, etc. I bought the braided tubing and secured it with a hog ring at each end. Ed Last edited by Ed Wendell; 03-20-2015 at 02:47 PM. Reason: spelling |
03-20-2015, 03:24 PM | #8 | |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Fuel line shield to prevent vapor lock?
Quote:
Did that help ? I've had good luck with them using a carburetor spacer and/or a heat shield under the carb. |
|
03-20-2015, 03:39 PM | #9 |
Senior Member
Join Date: Aug 2012
Location: Adrian , Mich.
Posts: 386
|
Re: Fuel line shield to prevent vapor lock?
Here is one that one of the vendors sell , wouldn't be hard to make one .
http://www.macsautoparts.com/ford_mo...al-finish.html |
03-20-2015, 03:45 PM | #10 | |
Senior Member
Join Date: May 2010
Location: Pace, FL near Pensacola
Posts: 374
|
Re: Fuel line shield to prevent vapor lock?
Quote:
|
|
03-20-2015, 05:34 PM | #11 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Fuel line shield to prevent vapor lock?
I used some of that split plastic tubing that newer cars use as a wiring harness, except I found some white, which reflects the heat. It helped my fuel problems caused by crap gas. Once I found and bought the good gas I was able to remove the white plastic wrap. I also add 4 oz. MMO to each 10 gallons of good gas.
|
03-20-2015, 05:42 PM | #12 | |
Senior Member
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,115
|
Re: Fuel line shield to prevent vapor lock?
Quote:
__________________
Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club |
|
03-20-2015, 05:56 PM | #13 |
Senior Member
Join Date: Sep 2011
Location: Livermore, CA
Posts: 124
|
Re: Fuel line shield to prevent vapor lock?
I've never heard of adding ATF to the fuel tank. What's the science behind this idea?
|
03-20-2015, 06:03 PM | #14 |
Senior Member
Join Date: Mar 2014
Location: Cleveland, Ohio
Posts: 2,763
|
Re: Fuel line shield to prevent vapor lock?
Last August, I did a 2 mile, parade that took 1 hour to drive in 90F heat... My car had 50/50 coolant and 4oz of MMO per 10 gals of gasoline.. Did MMO make a difference? I cannot say being a newbie but I've kept the 4oz/10 gals since.
__________________
-Mike Late 31' Ford Model A Tudor, Miss Daisy I don't work on cars --I'm learning about my Model A. Cleveland, Ohio |
03-20-2015, 06:09 PM | #15 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,848
|
Re: Fuel line shield to prevent vapor lock?
|
03-20-2015, 06:28 PM | #16 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Fuel line shield to prevent vapor lock?
Mike K. would know the science and correct terms.
I'm just the guy that sat in the rear of chemisty class and played with the bunsen burner. Adding the oil will help the crap gas to not boil so quickly. |
03-20-2015, 07:01 PM | #17 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,848
|
Re: Fuel line shield to prevent vapor lock?
What makes gasoline boil at a low temperature is the lighter ends (butanes, pentanes) not the alcohol. The lighter ends have always been there although more are blended in in the winter months. Your right tho, todays gas is crap...
|
03-20-2015, 07:27 PM | #18 |
Member
Join Date: May 2010
Location: Hixson, Tennessee
Posts: 77
|
Re: Fuel line shield to prevent vapor lock?
I made this heat shield when I was having vapor lock problems. Usually boiling in the carburetor is the problem. No problems since it was installed.
__________________
1929 Model A speedster 1930 Model A Coupe 1930 Model A Fordor 1931 Model A Pickup 1931 Model A Victoria 1931 Model A Fordor 1914 model T Touring 1915 Buick C-25 Touring |
03-20-2015, 07:32 PM | #19 |
Senior Member
Join Date: May 2010
Location: San Antonio, Texas
Posts: 160
|
Re: Fuel line shield to prevent vapor lock?
My old buddy Dennis, the B-17 pilot, told me he regularly added a quart of ATF to his gas tanks. I think he said he did it along with every oil change. So it's a fairly old trick.
Fearless |
03-20-2015, 08:32 PM | #20 |
Senior Member
Join Date: Sep 2011
Location: Livermore, CA
Posts: 124
|
Re: Fuel line shield to prevent vapor lock?
David, do you happen to have a photo to share, of the heat shield that you made?
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|