Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-24-2020, 02:56 PM   #1
Rick Leavitt
Member
 
Rick Leavitt's Avatar
 
Join Date: Jul 2020
Location: Bonney Lake Washington
Posts: 50
Default Ford Shock Absorber Fluid

What is everyone using to replace the Ford Shock Absorber Fluid?
Rick Leavitt is offline   Reply With Quote
Old 12-24-2020, 06:44 PM   #2
Hal Beatty
Senior Member
 
Hal Beatty's Avatar
 
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
Default Re: Ford Shock Absorber Fluid

I've topped mine off with Liquid Wrench Hydraulic Jack Oil; says it's good for hydraulic jacks and refillable shock absorbers. Has worked well so far... I think just about any hydraulic jack oil would be OK.
Hal Beatty is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-24-2020, 06:48 PM   #3
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: Ford Shock Absorber Fluid

I read a article about motorcycle fork oils, ATF is rated as good in it's viscosity range, and tractor multi viscosity transmission oil had a good rating ---depending on how worn the socks are
Kurt in NJ is offline   Reply With Quote
Old 12-24-2020, 08:46 PM   #4
VeryTangled
Senior Member
 
VeryTangled's Avatar
 
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 3,386
Default Re: Ford Shock Absorber Fluid

Hi Everyone! Here's what Bill Wzorek and Andrew Falandes say...

Dangit folks, hug the ones you love. I'd like to see Bill again.

https://www.fordbarn.com/forum/showp...76&postcount=6
__________________
-Jeff H

Have you thought about supporting the Early Ford V-8 Foundation Museum?
VeryTangled is offline   Reply With Quote
Old 12-25-2020, 10:05 AM   #5
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Ford Shock Absorber Fluid

Sponsored Links (Register now to hide all advertisements)
I would caution folks to make sure the shocks are empty of any previous fluid before attempting to change fluids. The old glycerin based and castor oil based fluids are not compatible with mineral oils.

I would gravitate toward an hydraulic oil with a viscosity that is near SAE 50 motor oil. SAE-50 motor oil is the same viscosity as SAE-90 gear oil but without the sulfuric acid/phosphoric acid based extreme pressure additives. A person may need a conversiion table for the difference between the ISO viscosity grading system and the SAE system since most hydraulic oils are now graded on the new international system. ISO-150 is very near SAE-40 and ISO-220 is very near SAE-50. Hydraulic oils would be the ideal fluid since that is what they are made for if there are any available in the higher viscosities

The viscosity will vary depending on the condition of the shocks. As they wear, the clearances get larger and larger so the viscosity will have to increase to allow function. If hydraulic oils aren't available in the high viscosity ranges then straight mineral aircraft motor oils may be an alternative such as AeroShell 100. Most jack oils are about SAE-20 or ISO-46 so thay may not be thick enough.

Last edited by rotorwrench; 12-25-2020 at 10:40 AM.
rotorwrench is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:39 PM.