Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-25-2020, 07:01 PM   #1
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Solo Motor Installation

I just got my engine back in the car on my own after replacing the cam gear and cleaning the pan. A few tips were discovered:
• I found that it was very important to have the motor as level as possible on the engine hoist to get the lips on the clutch housing square on the stock motor mounts.
• If a load leveler is used, make sure that the crank handle is pointed away from the firewall to make turning it easier.
• Along the same lines, the chain to the block at the firewall end needs to be attached to a head stud inboard from the end to avoid the chain hitting the firewall.
• Working by myself, it took a lot more going back and forth between the front of the car to looking at the clutch area than if working with an experienced Model A wrench spinner.
• Once the engine was resting on the motor mounts and slid up to the trans input shaft, with the trans housing aligned vertically with the clutch housing, I screwed the ratchet nut into the hub part of my two piece pulley, then turned it with my 1-3/8” box wrench to align the splines and that part turned out the easiest part of the task.
Bruce of MN is offline   Reply With Quote
Old 03-25-2020, 07:39 PM   #2
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,088
Default Re: Solo Motor Installation

Nice, Slow process but it can be done, as long as you have the patience. And as we all know we have the time! been there and done that!
Attached Images
File Type: jpg cars.jpg (66.3 KB, 34 views)
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-25-2020, 07:49 PM   #3
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Solo Motor Installation

Good job Bruce. I have removed and install my engine a few times, not something I would look forward to in the near future.

I actually shortened my load leveler ~4" to gain clearance from the firewall. Time and patience it can be accomplished.



Last edited by Y-Blockhead; 03-25-2020 at 08:03 PM.
Y-Blockhead is offline   Reply With Quote
Old 03-25-2020, 07:58 PM   #4
duke36
Senior Member
 
Join Date: Jun 2015
Posts: 1,414
Default Re: Solo Motor Installation

Good info. Did you need a frame spreader, as you mentioned stock rear mounts?
Also, was the light bar removed?
duke36 is offline   Reply With Quote
Old 03-26-2020, 03:33 AM   #5
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Re: Solo Motor Installation

Yes, I used our club's frame spreader and I removed the light bar and the front bumper to get my engine hoist in far enough. That also took some re-positioning of the front jack stands.

Several false starts with learning some of the above points! When I removed and installed the engine 10 years ago, I didn't have the load leveler and it seemed easier. I tilted the engine by having the center link offset from the chain mid-point.

Bruce of MN is offline   Reply With Quote
Old 03-26-2020, 07:37 AM   #6
David R.
Senior Member
 
Join Date: Aug 2016
Location: West Virginia
Posts: 430
Default Re: Solo Motor Installation

Sponsored Links (Register now to hide all advertisements)
Here is how I pulled mine solo. Don’t know how it will work to install. I was set to take my block to machine shop last week, but I guess that’s on hold for now.
Attached Images
File Type: jpg 4BE04453-9AA2-4000-A104-9176F29E330A.jpg (47.5 KB, 192 views)
David R. is offline   Reply With Quote
Old 03-26-2020, 08:18 AM   #7
macdonge
Senior Member
 
macdonge's Avatar
 
Join Date: May 2015
Location: Frelighsburg, QC
Posts: 165
Default Re: Solo Motor Installation

I'll be facing a reinstall soon... whenever I can get to the shop that recently re-poured the engines bearings. Any thoughts on whether it's easier to do with the transmission in the car, attached to the driveshaft, or with it out of the car and attached to the flywheel housing?
macdonge is offline   Reply With Quote
Old 03-26-2020, 08:21 AM   #8
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: Solo Motor Installation

Trial & error is a fantastic way to learn about our Model "A" Fords.
Attached Images
File Type: jpg 190A Model A Engine Teardown 906kb.jpg (85.4 KB, 123 views)
File Type: jpg 190A Model B Engine Rebuild by Schwalm 555KB.jpg (64.7 KB, 124 views)
File Type: jpg 190A Model B Engine Teardown 768kb.jpg (76.9 KB, 112 views)
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 03-26-2020, 08:32 AM   #9
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Re: Solo Motor Installation

Quote:
Originally Posted by macdonge View Post
. Any thoughts on whether it's easier to do with the transmission in the car, attached to the driveshaft, or with it out of the car and attached to the flywheel housing?

Both times, I supported the transmission and unbolted the flywheel housing from the trans.
Bruce of MN is offline   Reply With Quote
Old 03-26-2020, 11:34 AM   #10
duke36
Senior Member
 
Join Date: Jun 2015
Posts: 1,414
Default Re: Solo Motor Installation

Is there any advantage such as less stress on the block/studs to lift as in post 6 with the head on ? The vendors sell eyebolts to attach to the spark plug holes.
duke36 is offline   Reply With Quote
Old 03-26-2020, 05:21 PM   #11
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Re: Solo Motor Installation

My grade 8 head studs are plenty strong and the chain link on the exhaust stud is close to the base, so minimized bending load.
Bruce of MN is offline   Reply With Quote
Old 03-27-2020, 06:42 AM   #12
David R.
Senior Member
 
Join Date: Aug 2016
Location: West Virginia
Posts: 430
Default Re: Solo Motor Installation

Quote:
Originally Posted by duke36 View Post
Is there any advantage such as less stress on the block/studs to lift as in post 6 with the head on ? The vendors sell eyebolts to attach to the spark plug holes.
I made my fixture out of angle iron. Laid a cardboard pattern down over oily spark plug holes to locate them and drilled angle to match. I was worried about using the eye bolt thing in just one hole. I figured this way the stress is divided by four. I guessed at lifting hole location, but it balanced really well. Had to grind a little relief on back side of angle for a couple of head nuts. I had planned to rent an engine lift, but none available in my area so I had to rig that too.
David R. is offline   Reply With Quote
Old 03-27-2020, 07:45 AM   #13
77Birdman
Senior Member
 
Join Date: Nov 2018
Location: North Eastern MD
Posts: 486
Default Re: Solo Motor Installation

Glad you were able to accomplish this by yourself successfully.
77Birdman is offline   Reply With Quote
Old 03-28-2020, 03:25 AM   #14
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Re: Solo Motor Installation

Quote:
Originally Posted by 77Birdman View Post
Glad you were able to accomplish this by yourself successfully.
Not much choice these days.

The Les Andrews book surely says this, but why would I read it in detail? The four motor mount bolts should go in before the trans is bolted to the motor. That makes it a lot easier to pry and hoist the engine around to get those babies lined up.
Bruce of MN is offline   Reply With Quote
Old 03-29-2020, 12:29 PM   #15
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Solo Motor Installation

Quote:
I actually shortened my load leveler ~4" to gain clearance from the firewall. Time and patience it can be accomplished.
So, what is the shortened length?
I am presently in the process of assembling materials to build a load leveler, so it would be nice to know how long or short would be optimal.
Tnx, Ken
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 03-30-2020, 07:41 AM   #16
77Birdman
Senior Member
 
Join Date: Nov 2018
Location: North Eastern MD
Posts: 486
Default Re: Solo Motor Installation

I did about 99.9% of the work on my resto (70's car) solo, oddly enough the one thing I needed help with was installing the hood. I thought about for about an hour or so how to rig something up then finally just went inside and asked my wife to give me a hand!
77Birdman is offline   Reply With Quote
Old 03-30-2020, 01:31 PM   #17
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Solo Motor Installation

Quote:
Originally Posted by katy View Post
So, what is the shortened length?
I am presently in the process of assembling materials to build a load leveler, so it would be nice to know how long or short would be optimal.
Tnx, Ken
Not sure if it is optimal but the length of the bar is ~16" now, shorter than the head. When it was full length it hit the firewall. I used #1 and #4 spark plug holes for lift points. It could be even a little shorter.
Y-Blockhead is offline   Reply With Quote
Old 03-31-2020, 10:44 AM   #18
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Solo Motor Installation

Quote:
Not sure if it is optimal but the length of the bar is ~16" now, shorter than the head. When it was full length it hit the firewall. I used #1 and #4 spark plug holes for lift points. It could be even a little shorter.
Sounds good, thanks, Ken
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 04-02-2020, 07:58 PM   #19
lsr490
Member
 
Join Date: May 2012
Location: RTP North Carolina
Posts: 68
Default Re: Solo Motor Installation

Quote:
Originally Posted by Y-Blockhead View Post
Not sure if it is optimal but the length of the bar is ~16" now, shorter than the head. When it was full length it hit the firewall. I used #1 and #4 spark plug holes for lift points. It could be even a little shorter.
I was just getting ready to cut four inches out of mine. I had to put a bunch of towels on my firewall getting the engine out. If you had to do it again would you go 14" or 15"?
Thanks
__________________
"Avoid Model A Mythsteries. Read, study and challenge ALL advice with current logic, chemistry and technology!" author unknown
lsr490 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:30 PM.