Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-19-2020, 08:43 AM   #1
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Default gas pedal linkage 46 48 v8

does any have diagram or photo of how this goes together at the floor?
is there a seal or a bushing that supports the pedal rod?
thanks
mike d is offline   Reply With Quote
Old 09-19-2020, 06:07 PM   #2
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 304
Default Re: gas pedal linkage 46 48 v8

Mike. The pedal rod, 9727, "snaps" into the cavity on the underside of the gas pedal, and goes through the firewall into the engine compartment. That rod connects to a spring loaded (throttle return) cross shaft 9725, that bolts to the firewall above the bellhousing. Another rod 9747, connects the cross shaft to the carb throttle. The rods have "spring loaded ends that lock on the ball ends of the respective connections, and there are rubber insulators P/N 91A-9714-A, that go over the ball ends.
Attached Images
File Type: jpg Flathead_fuelsystm_1942-46car.jpg (84.3 KB, 38 views)
51woodie is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-19-2020, 06:55 PM   #3
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Default Re: gas pedal linkage 46 48 v8

thanks much mike
mike d is offline   Reply With Quote
Old 09-19-2020, 07:00 PM   #4
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Smile Re: gas pedal linkage 46 48 v8

do you know of any supplier who stocks those insulators?
thanks again
mike d is offline   Reply With Quote
Old 09-19-2020, 07:10 PM   #5
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 304
Default Re: gas pedal linkage 46 48 v8

Dennis Carpenter or Bob Drake
51woodie is offline   Reply With Quote
Old 09-19-2020, 07:22 PM   #6
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Smile Re: gas pedal linkage 46 48 v8

Sponsored Links (Register now to hide all advertisements)
thanks again
mike d is offline   Reply With Quote
Old 09-19-2020, 08:34 PM   #7
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Default Re: gas pedal linkage 46 48 v8

have you seen them in use? thanks
mike d is offline   Reply With Quote
Old 09-19-2020, 08:37 PM   #8
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 1,883
Default Re: gas pedal linkage 46 48 v8

As a side note, the 9727 linkage goes through the floor pan not the firewall (there is no seal aside from the fact it passes through the floor mat), and the 9714 insulators are not used when using reproduction linkages.
35fordtn is offline   Reply With Quote
Old 09-20-2020, 05:11 AM   #9
51woodie
Senior Member
 
51woodie's Avatar
 
Join Date: Apr 2018
Location: Chelmsford, ON Canada
Posts: 304
Default Re: gas pedal linkage 46 48 v8

Michael. Thank you for correcting the 9727 transition. Also, for the info on original vs repro linkage ends. I must have original linkage, because the rubbers fit my balls. Can I say that?
51woodie is offline   Reply With Quote
Old 09-20-2020, 06:33 AM   #10
mike d
Member
 
Join Date: May 2010
Location: woburn, ma
Posts: 30
Smile Re: gas pedal linkage 46 48 v8

that was a perfectly acceptable comment
mike d is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:01 AM.