|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-26-2022, 02:55 PM | #1 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Water Pump Replacement
I finally got my water pump off and removed the aluminum two-blade fan. I had to use a wheel puller to remove the fan blade.
The guy who replaced my fan a couple years back warned me that fans can work loose (as mine had already done). The fan was very hard to remove; so, I’m thinking he used some kind of thread locking product on it. Should I use some sort of thread locking product? Can I reuse the fan woodruff key without having issues? What should I use on the paper gasket? I was thinking about using Hylomar Blue. Sent from my iPhone using Tapatalk |
06-26-2022, 03:09 PM | #2 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Water Pump Replacement
Do you remove the pump to replace it?
Original steel fan blades can come apart. Reproduction aluminum ones don't. The tapered pulley is what holds it on for the most part. The cotter pin in the shaft is more than enough to hold the fan in place after tightening.
__________________
"The more things change, the more they stay the same." |
Sponsored Links (Register now to hide all advertisements) |
|
06-26-2022, 03:12 PM | #3 |
Senior Member
Join Date: May 2010
Location: brentwood, ca
Posts: 4,233
|
Re: Water Pump Replacement
And install a washer under the nut.
|
06-26-2022, 04:09 PM | #4 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Water Pump Replacement
Quote:
Thanks for the feedback, but all I know is that the fan on my car was aluminum, and it eventually worked loose and galled out the taper to the point that the fan was definitely loose, which is why I had it replaced a couple of years ago. I checked the fan several months prior, and it was tight. So, I’m taking the Model A mechanic’s warning about loose aluminum fans seriously. They can loosen. Sent from my iPhone using Tapatalk Last edited by shew01; 06-26-2022 at 05:21 PM. |
|
06-26-2022, 04:10 PM | #5 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
|
06-26-2022, 04:23 PM | #6 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
|
06-26-2022, 04:48 PM | #7 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Water Pump Replacement
The washer is not original and not really needed. The nut needs to be tight to keep the fan from galling the shaft. Whoever did yours did not tighten it nearly enough. You need to make sure you got the key in the keyway and it is on square all the way. Tighten the nut until you can tighten no more. Cotter pin it and it won't ever come loose.
__________________
"The more things change, the more they stay the same." |
06-26-2022, 05:23 PM | #8 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
When I removed the old water pump, it looks like there was some sort of gasket sealer even on the studs. Can the studs leak antifreeze?
Sent from my iPhone using Tapatalk |
06-26-2022, 07:43 PM | #9 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Water Pump Replacement
If you look at the head, 3 of the 4 stud holes don't go through to the coolant (unless someone has been very heavy handed and broken out the back of one). Sealant should only be needed on the stud that goes through to the coolant at the most. I never use a sealant there other than a smear of silicone (or Permatex #2) on the gasket.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
06-26-2022, 08:57 PM | #10 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Elsewhere I have described the issue of both aluminum fan hubs (the hole was done as an "as cast" form and tend to "wasp waisted" reverse barrel shape) and the pump shafts (many shafts were provided with an actual "barrel shape" as in two different tapers.)
Its all a matter of "quality." The issue(s) are overcome somewhat by repeated tightening which "stretches" the aluminum hub over the barrel shaped taper, galling the aluminum and possibly the shaft. In effect what one achieves by repeated tightening is what the machinists call an "interference fit." Hence the difficulty of removal. While a locking type material MAY have been used, it likely was not, and the interference would force it out if it were. It's not like a "real" fit in this case where the aluminum hub stretches uniformly over the uniformly tapered shaft. Instead you tend to get "point contact." (line contact?) The use of a washer compensates somewhat for the point (or line) contact thus formed, and the washer gives you some freedom of motion for additional tightening without bottoming out the nut. The later shafts and hubs are better - more uniform in taper and a step up in quality - but I'm considering the issue is far from solved. Joe K
__________________
Shudda kept the horse. |
06-26-2022, 09:03 PM | #11 |
Senior Member
Join Date: Aug 2021
Location: alberta canada
Posts: 585
|
Re: Water Pump Replacement
not what you asked but some info that may help next time.
to get those aluminum fan blades off easier i use my electric heat gun, heat them up. the aluminum is quick to expand and they usually come off pretty easy.
__________________
old ugly my old father-in-law told me. "listen close when people tell you how to do stuff they may know something. then do it the way you want." |
06-26-2022, 09:29 PM | #12 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Water Pump Replacement
Good tip, I'll remember that (till I need it).
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
06-28-2022, 04:21 AM | #13 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
I may end up needing to find another water pump. I don’t know if the rebuilt one that I have is going to work. Does anyone have new water pumps in stock at the moment? Ives heard that most Model A vendors are out of stock at the moment.
Sent from my iPhone using Tapatalk |
06-28-2022, 09:55 AM | #14 | |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Quote:
Although the $1 water pump I bought at the Epping Antique Auto Flea Market could be cleaned up, repacked, and re-used. It wouldn't be a thing of beauty but it could work. In rebuilding a pump you need to determine if you need the "extended shaft" to compensate for wear of the bridge in your cylinder head. Putting the impeller in EXACTLY the right spot can be challenging. There are other ways to compensate for the worn bridge. One method used is to drill and tap the bridge for a brass bolt - and its converse to drill and tap the impeller end of the shaft. Some of the "forever" pumps have the front bearings such that the shaft is totally constrained - a bridge is not even necessary and frequently the impeller end of the pump shaft nose is cut off (not needed) And in rebuilding one will do well to ask the supplier if the stainless shaft diameter is anything less than the 0.625 of a properly sized original: MANY sources of rolled stainless rod (from which many of these shafts are made) take their sizing a thousandth or two small from the rod stock they start with. A good parts supplier will know and he will give assurance that a pressed on impeller will truly press on with a correct fit (most who do this "pin" the impeller as a security measure.) The brass or plated "spanner nut" (gland nut) can be either "original" - or provided with a rubber lip seal. I tend to like original since this doesn't rule out installation of a ring of packing even for a rubber lip seal pump. The brass "gland/shaft bearing" (The spanner nut screws onto this) can be either original or provided with a rubber lip seal - or two! Be sure the grease holes in casting and bearing line up when you press them together. And the pump "front" bearing can be either original using the spring-type "chevron'ed" spring fit bearing shell (part next to the casting) and an original Hyatt type bearing which rotates directly on the shaft. Or it can use a Torrington inner "shaft race" and a cup style Torrington needle bearing put directly into the casting. I don't have the numbers for these but if you find your stainless shaft a little undersized by "center punching" the shaft repeatedly or "knurling" one can compensate for the slop and hold the race on the shaft as an "interference fit." (you don't want the race turning separate from the shaft.) There is some mechanical "art & science" to rebuilding a water pump, and choices to which option you pursue. Or like the $1 pump of my acquisition, simply clean up the parts, pack it, and make it work? Luck of the draw is a force too. Joe K
__________________
Shudda kept the horse. Last edited by Joe K; 06-28-2022 at 05:11 PM. |
|
06-28-2022, 12:25 PM | #15 |
Senior Member
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
|
Re: Water Pump Replacement
To answer your question "Can I reuse the fan woodruff key without having issues?
The answer is yes, unless it is chewed up beyond use, should fit nice and snug and tight with no missing chunks out of it, but if you have any doubts about the key change it out...they are cheap.
__________________
Keith Shawnee OK '31 SW 160-B |
06-28-2022, 06:47 PM | #16 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
When I initially looked at my Woodruff key, I thought it might be reusable, but, on closer inspection, it was a bit twisted. I found a replacement at Ace Hardware.
Sent from my iPhone using Tapatalk |
06-28-2022, 06:49 PM | #17 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
Quote:
Advance Auto had a package of assorted sizes, but only one of five looked like it would fit. Bratton’s was out of stock. It seems most Model A vendors are out of stock on water pumps, parts, and rebuild kits. Sent from my iPhone using Tapatalk |
|
06-29-2022, 06:46 PM | #18 |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,068
|
Re: Water Pump Replacement
Shew - I use Hylomar Blue on almost all paper gaskets to good effect. Having said that, note Synchro909's comment about only one stud communicating with water, that's an excellent point that I had not previously thought about.
JayJay
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan |
06-29-2022, 09:41 PM | #19 |
Senior Member
Join Date: Aug 2021
Location: alberta canada
Posts: 585
|
Re: Water Pump Replacement
another thing about replacing your water pump is the internal clearance in the cylinder head.
this clearance should be checked to make sure the shaft does not move rearword and the impeller fins don't interfere with the inside head casting. most of the time its plug and play but i have seen some that the impeller has been destroyed because it hit the inside. there is a spec for the clearance from the end of the shaft to the inside bearing boss and the distance the impeller is supposed to be pressed onto the shaft. all im saying is check that it turns without interference and without to much forward movement. don't rely on the fan belt keeping it in position.
__________________
old ugly my old father-in-law told me. "listen close when people tell you how to do stuff they may know something. then do it the way you want." |
06-29-2022, 10:30 PM | #20 | |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Quote:
Credence to this thought comes also in that there was at least one maker of Model A "Aftermarket" pumps who utilized a later V8 type impeller - and a single impeller of this lesser vane did perfectly fine in the Model A application. These aftermarket pumps are actually probably the first "leakproof" type pump having as they do a ceramic supposedly leakproof seal surface. The image is an Ebay image so it probably won't last but these aftermarket pumps can be described quickly as "not having a gland or adjustment" otherwise similar to the original Model A pump. The sleeve front bearing is probably the most undesirable part of this pump. Joe K
__________________
Shudda kept the horse. |
|
06-29-2022, 11:24 PM | #21 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Water Pump Replacement
Quote:
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
06-30-2022, 08:41 AM | #22 | |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Quote:
Most who use thermostats/restrictors tend to say "My car doesn't boil over with the flow restriction" not realizing that a flow restriction puts "head" at the point where boiling over is most likely to occurs (i.e. the upper hose where pressure downstream of the pump is minimum and temperature is maximum.) I have considered that a thermostat on a partially plugged radiator MIGHT result in slower flow THROUGH the radiator and cooler water to the engine lower connection, which by itself might limit boil-over - but like the impeller issue I'm not prepared to defend it. I can see a thermostat on its own merits. There is an optimal "cylinder temperature" for both efficiency of combustion AND wear on the cylinder walls. The reason for a later age placement of thermostats is to take advantage - and to provide a "warmer" engine - which the Model A lacked. Not unusual during the Model A era AND today in trucking to put a cardboard in front of the radiator in the winter to limit over-cooling. Still, its funny that an aftermarket water pump might take advantage of reducing flow at the same time that everyone's radiators were becoming "flow obstructed" in a normal radiator life. One's early reaction to repeated boil-overs MIGHT be to replace the water pump - and not address the radiator issue. It might have even temporarily solved the issue. Joe K
__________________
Shudda kept the horse. |
|
Sponsored Links (Register now to hide all advertisements) |
|
07-01-2022, 11:22 AM | #23 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
I decided to do a test fit of my rebuilt water pump, and it doesn’t fit right—it does not go all the way into the head. The previous owner apparently rebuilt the pump (which I purchased with the car), and I’m guessing the impeller is not on the right place on the shaft. What are my options?
Sent from my iPhone using Tapatalk |
07-01-2022, 11:23 AM | #24 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
The new (rebuilt) water pump is on the left.
Here is the gap I’m seeing. Sent from my iPhone using Tapatalk |
07-01-2022, 04:44 PM | #25 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
If the pump spins as it is built (check with the fan on) then you can cut down the nose (center shaft extension at the impeller) so without gasket it fits "tight." The additional thickness of the gasket is about the recommended 0.010 thickness for "fore & aft" movement of the pump shaft.
You don't want to constrain the shaft too tight with either original packing or the "lip seal" of a leakless pump. (Some leakless pumps come "pre-constrained" by the front bearing.) A little "front-back" movement of the shaft sometimes allows a drip or two to get past the lip seal, but it prevents the lip seal from wearing a groove in the shaft. Joe K
__________________
Shudda kept the horse. |
07-01-2022, 06:09 PM | #26 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,127
|
Re: Water Pump Replacement
Sponsored Links (Register now to hide all advertisements)
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
07-01-2022, 06:21 PM | #27 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
The $1 water pump I referred to earlier is now disassembled. It was seized and it took some doing (and a punch and hammer to unscrew the gland nut) to allow removal of the shaft.
The failure mode of the pump was the prior owner simply "tightened up" the gland nut too tight and bound the shaft. The nut was within two turns of "home." Looking at the packing I'm not sure anyone ever added a ring of packing and what is there is HARD. I'm pretty sure I can remove the packing, clean up the galvanized nut and re-pack. The shaft is probably the best "used" shaft I've seen and even the hyatt bearing at the front appears re-usable as is. I guess this is a "gloat." Probably my 8th pump... Parts ARE an addiction. Joe K
__________________
Shudda kept the horse. |
07-01-2022, 06:27 PM | #28 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Water Pump Replacement
Quote:
How would you cut it? Sent from my iPhone using Tapatalk Last edited by shew01; 07-01-2022 at 06:38 PM. |
|
07-01-2022, 06:45 PM | #29 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Best would be to disassemble the pump and turn the shaft in a lathe.
Given you likely don't have one, an alternative might be found in holding the entire pump in a vise, and by using the fan, "turn" the shaft while holding a 4-1/2" hand grinder against the end. This might be laborious - maybe take off a slice using a hack-saw and THEN use the grinder to "fine-tune" the fit (and prepare what will be a metal-to-metal contact surface between the bridge and the pump shaft.) Blow your grindings off onto the bench or otherwise protect the pump from intrusion (situated rag or create for yourself an "operating theater.") I can see that one might "measure" between the flange of the pump and the nose - and then measure between the head pump mount flange and the recession in the bridge. A "sharpie" works well to "blacken" the metal surface upon which you can scribe a line with an X-Acto knife to guide your cutting. It presents problems - but careful cutting and patience is the key. Rather than "re-press" the impeller (you may not see a "pin" that most use in addition to the press fit) I might choose modify the shaft. The look (pix) it does appear to be the "extended shaft" version. As another has said, commonly supplied this way so you may fit it to your head. Joe K
__________________
Shudda kept the horse. |
07-01-2022, 09:35 PM | #30 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
Joe,
Hmm… I’m not sure I totally understand. (I am a total novice at water pumps on Model A’s. Under normal circumstances, I’d just buy a replacement, but replacements are out of stock everywhere I’ve checked—Bratton’s, Snyder’s, MAC’s, Mike’s.) What about measuring the old water pump and cutting the rebuilt one to match the length of the old one? How could I accurately measure from the mounting flange to the end of the spindle that goes into the head? (The impeller is an oddball shape. How would I get around that and get an accurate measurement?) Sent from my iPhone using Tapatalk |
07-02-2022, 04:07 AM | #31 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Likely you would have the same issue with a replacement - or maybe the converse - shaft too short resulting in too much forward-back movement of the shaft/impeller. Sellers generally sell what will cover most circumstances and too long is better than too short in that instance.
Your thought to measure an existing functional pump is a good one. Just leave yourself enough to remove with the grinder so you don't "overshoot." Overshooting can result in a need to "add" metal, or do the "tap & insert for a brass bolt" extension fix. The fix can be performed by having a welder add metal and re-grind. My measure might be done using a technique called a "bridge gauge" - basically amounting to three blocks of wood set up to "bridge" the impeller. But I have the vernier caliper (with extension) to measure how much bridge the bridge actually bridges. A ruler might work if you're careful. Joe K
__________________
Shudda kept the horse. |
07-02-2022, 04:12 AM | #32 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Water Pump Replacement
Harbor Freight sells a cheap 4-1/2" grinder on sale for $9.99. This can be fitted with either the typical "cup" wheel (actually more dishware than teacup) or with a THIN blade (typically 0.040 thick) which will cut a "slice" like a hack-saw. And probably do it easier and more accurately. Both wheel patterns are sold in packs of 5 at HF.
They're not my fave for power tools, but $9.99 (or $14.99 normal) is still pretty cheap for a tool which you don't try to fix if it breaks. And mine is still soldiering along. Joe K
__________________
Shudda kept the horse. |
07-03-2022, 08:56 AM | #33 |
Senior Member
Join Date: Oct 2019
Location: Virginia
Posts: 140
|
Re: Water Pump Replacement
I'm going through the same process. I'm planning on using a bench grinder to shorten the shaft after the pump is assembled. I will hand finish the shaft end with fine emery cloth after the grind, attempting to get it as smooth and square as possible. The last picture is the collar you can use to control the end play if you grind off too much.
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive 1935 Model 48 Tudor |
07-03-2022, 09:21 AM | #34 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
A friend in our club has a lathe, and he plans to help me with it.
I have a vernier caliper, but I don’t know if it has enough reach to measure like you did. Roughly, it looks like my rebuilt pump is about 1/4” too long going into the head. Measuring is part of my problem. The water pump (for me) is difficult to measure. Sent from my iPhone using Tapatalk |
07-03-2022, 09:23 AM | #35 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
I ordered a collar, and it came in a couple of days ago. At the moment, I can’t get the pump bolted to the head because the large gap between the pump and the head.
Sent from my iPhone using Tapatalk |
07-03-2022, 01:24 PM | #36 |
Senior Member
Join Date: Oct 2019
Location: Virginia
Posts: 140
|
Re: Water Pump Replacement
You will need a precise depth measurement from the water pump mounting flange on the head to the the point inside the head where the end of the pump shaft would contact. This should then equal the distance from the pump flange on the pump to the shaft end. Your friend with the lathe will need this to know how much to take off. Or, he could just cut off 1/4"+ and then you could adjust your end play with the collar.
I'm building a spare pump, so my present pump is still installed. I'll remove it to hand fit the spare pump. The picture is the spare pump with the long (not yet shortened) shaft. I anticipate removing about 1/4 inch, so the nominal measurement looks like 2 3/4 plus whatever wear you have in the head. When the gasket is installed this would give you the desired end play.
__________________
1929 Town Sedan (Briggs) 155B, Mitchell Overdrive 1935 Model 48 Tudor |
07-03-2022, 05:58 PM | #37 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
Quote:
I’ve looked at this picture about a dozen times, and I think I finally figured out how to measure the water pump. Thanks for posting. Sent from my iPhone using Tapatalk |
|
07-03-2022, 08:40 PM | #38 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,127
|
Re: Water Pump Replacement
If you just install the pump and measure the gap between the pump and the head plus a little more, remove that from the shaft end,presto
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
07-11-2022, 03:56 AM | #39 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Water Pump Replacement
Yesterday, I got the rebuilt water pump installed. I used a little Permatex around the stud that is open to the water jacket, and I used Blue Hylomar on the gasket and water hose to make future removal easier. My wife and I took the car out for about a 10 mile test drive. So far, no leaks. I have some radiator flush in the radiator at the moment. I'll probably take the car out a time or two before replacing that with 50/50 antifreeze.
Sent from my iPhone using Tapatalk |
|
|
Sponsored Links (Register now to hide all advertisements) |
|