Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-20-2017, 06:48 AM   #1
OLD AS I
Senior Member
 
OLD AS I's Avatar
 
Join Date: Oct 2014
Location: Oakwood, ON Canada
Posts: 251
Default Torque wrench

Have to replace my torque wrench, any comments on what make, sweep needle dial gauge or clicker type, just for use on V8 flat heads so perhaps a range of 40-80 ft lbs, thanks for input, .......... cheers
OLD AS I is offline   Reply With Quote
Old 03-20-2017, 07:12 AM   #2
37 Cab
Senior Member
 
37 Cab's Avatar
 
Join Date: Dec 2014
Location: Miami Oklahoma
Posts: 535
Default Re: Torque wrench

I have both a dial gauge and clicker type. If you get the clicker type be sure to back off the torque setting after each use or it will be out of calibration after a while. I like the clicker for ease of use and initial torque. The dial suits me better for lower torque values. If I only had one it would be the dial type just because I trust it.
__________________
Tommy
37 Cab is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-20-2017, 07:31 AM   #3
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: Torque wrench

Your arm may get shaky after about the 37th head bolt so it may be hard to read the dial type! I've had good results with the $12-14 Harbor Freight clickers. I have an electronic torque wrench tester and the HF ones are within a pound or two. One of the car magazines did a test a few years ago and found the HF ones to be accurate also. It takes a little squinting, bright light or magnifying glass for me to read the scale, though.
40 Deluxe is offline   Reply With Quote
Old 03-20-2017, 08:12 AM   #4
luvmyclassics
Senior Member
 
luvmyclassics's Avatar
 
Join Date: Jan 2011
Location: The Villages, FL
Posts: 193
Default Re: Torque wrench

Harbor Freight also sells a torque wrench calibration unit for $29.00

I just bought one but have not tested it.

Lots of you tube videos about how accurate it is.
luvmyclassics is offline   Reply With Quote
Old 03-20-2017, 10:01 AM   #5
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Torque wrench

just a few weeks back i was putting heads on a v8 using an old snap on torque wrench i had just bought at a swap meet last summer. i had a nice snap on bought new in the 70's that burned in a fire, dial type, i liked it and bought this other one. so putting on heads, i only got to 40lbs and it seemed to me to be harder than it should, so i stopped to check my wrench against another. sure enough it was reading 12lbs lighter than the neighbors. good thing i stopped. so thinking it was a high quality thing i looked into having it rebuilt. reading posts on the garage forum i came across the post from a man that works at a place that rebuilds them. take it how you wish, but he said, the dial type are most accurate, and most sensitive to being banged around. the click type can be good if you always back off the spring, and you get the most bang for your buck with the plain ol cheap beam type. they may be off a pound or so when new but will most likely stay that way your whole life. so if you like to just throw it in the drawer, and not treat it like an egg, your better off with the cheap beam. me, i bought a used beam off the neighbor for ten bucks instead of sending the snap on out for a 100+ rebuild
cas3 is offline   Reply With Quote
Old 03-20-2017, 10:15 AM   #6
Mark Slight
Senior Member
 
Mark Slight's Avatar
 
Join Date: May 2010
Location: Dixon, CA
Posts: 473
Default Re: Torque wrench

Sponsored Links (Register now to hide all advertisements)
oldasi,

As a former Snap-On Dealer in the USA I took my customers torque wrenches to the local Snap-on repair center had had them calibrated. Most of them did not need to be overhauled.

You may want to check your local phone book for a Snap-On dealer in your area.

Mark
Mark Slight is offline   Reply With Quote
Old 03-20-2017, 10:21 AM   #7
Barry-ct
Senior Member
 
Barry-ct's Avatar
 
Join Date: May 2010
Location: Newington, Connecticut
Posts: 1,374
Default Re: Torque wrench

I have a beam type that I bought in 1974 and it's still accurate. I also have 3 of the Harbor Freight ones and they are also accurate against a professional Snap On. I use the HF ones in my lawn mower repairs that I do, and are fine.
__________________
Barry

50 F-1
Barry-ct is offline   Reply With Quote
Old 03-20-2017, 11:04 AM   #8
bruce lee
Senior Member
 
Join Date: Jun 2015
Location: Nipomo ca.
Posts: 132
Default Re: Torque wrench

Mine from snap on is brand new digital. It vibrates, and beeps loud at correct torque. It also does angles and a lot more than I will ever need. I plan on building a lot of projects that need good torque values so I stepped up and bought one. It was around 500.00$. I just can't buy cheap junk tools so I stay as far from hf as possible. I would say just buy a craftsmen if you don't want to spend a lot of money.
bruce lee is offline   Reply With Quote
Old 03-20-2017, 12:05 PM   #9
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,879
Default Re: Torque wrench

Lowe's and Home Depot sell a good "clicker" type wrench.
Don't waste your money on a Harbor Freight torque wrench.
The quality is poor.
19Fordy is offline   Reply With Quote
Old 03-20-2017, 12:39 PM   #10
STEVE O
Senior Member
 
STEVE O's Avatar
 
Join Date: May 2010
Location: QUICKSBURG VA
Posts: 706
Default Re: Torque wrench

I have a older Snap-on "clicker" style torque wrench. Shortly after paying to have it calibrated, the ratchet head has went bad (stripped out inside the head)after getting pissed at my local Snap-on man I have checked with 3 other salesmen and the head is discontinued so I am told I am out of luck. The only thing they can offer is sell me a new one. No way! I'll buy the craftsman for less than half.
STEVE O is online now   Reply With Quote
Old 03-20-2017, 01:01 PM   #11
Tim Ayers
Senior Member
 
Join Date: May 2010
Location: NJ
Posts: 6,144
Default Re: Torque wrench

I have a Precision Instruments bar type torque wrench. It's a 1/2" version, made in the USA and was under $150. I'm assuming a 3/8" would be cheaper.
Tim Ayers is offline   Reply With Quote
Old 03-20-2017, 01:10 PM   #12
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: Torque wrench

Remember you need to torque the rear axle nut. A couple of hundred pounds (depending on where you are reading). Maybe you need 2 different wrenches.

Charlie Stephens
Charlie Stephens is offline   Reply With Quote
Old 03-20-2017, 06:00 PM   #13
Bruce Lancaster
Member Emeritus
 
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
Default Re: Torque wrench

I read an interesting torque wrench article by a NASCAR team chief, who was of course VERY picky about every detail.
He said to use the clickers for all the heavy iron work, with frequent calibrations just for insurance.
For connecting rods only, he used the old fashioned beam and pointer in a range close to the torque needs of his rods. Nothing to get out of order and all the accuracy that one would need for fasteners that are rather low torque AND absolutely critical.
Bruce Lancaster is offline   Reply With Quote
Old 03-20-2017, 06:31 PM   #14
flatford39
Senior Member
 
Join Date: May 2010
Location: NE Illinois
Posts: 499
Default Re: Torque wrench

Quote:
Originally Posted by Tim Ayers View Post
I have a Precision Instruments bar type torque wrench. It's a 1/2" version, made in the USA and was under $150. I'm assuming a 3/8" would be cheaper.
Precision Instruments is the manufacturer for Snapon.
flatford39 is offline   Reply With Quote
Old 03-20-2017, 06:55 PM   #15
OLD AS I
Senior Member
 
OLD AS I's Avatar
 
Join Date: Oct 2014
Location: Oakwood, ON Canada
Posts: 251
Default Re: Torque wrench

Well, bite the bullet and bought a Snap-on, see its made in USA, 3/8" drive, 50 ft-lb, not cheap, $349.80 shipped to Canada, has to come from Crystal Lake ILL direct from Snap-on, dial needell gauge.
OLD AS I is offline   Reply With Quote
Old 03-20-2017, 07:52 PM   #16
Capt Kirk
Senior Member
 
Capt Kirk's Avatar
 
Join Date: May 2015
Location: Clarkston MI
Posts: 830
Default Re: Torque wrench

Tight plus a half turn
__________________
35 Ford Cabriolet
56 Chevy Pickup
63 VW Bug
Empty wallet
Capt Kirk is offline   Reply With Quote
Old 03-20-2017, 08:14 PM   #17
OLD AS I
Senior Member
 
OLD AS I's Avatar
 
Join Date: Oct 2014
Location: Oakwood, ON Canada
Posts: 251
Default Re: Torque wrench

Capt Kirk, you meaning to turn tight then 1/2 turn, no torque wrench ?
OLD AS I is offline   Reply With Quote
Old 03-20-2017, 08:33 PM   #18
36coupe
Senior Member
 
36coupe's Avatar
 
Join Date: Oct 2012
Location: Eastcoast
Posts: 859
Default Re: Torque wrench

I have a Gray Canada 3/8 clicker for 35 years and I always wind off the tension after use. I check it with a newer one once in while by setting them at the same setting and joining them together with what ever sockets works and see if they click at the same time.
36coupe is offline   Reply With Quote
Old 03-20-2017, 09:46 PM   #19
cas3
Senior Member
 
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,543
Default Re: Torque wrench

today i saw a friends snap on, dial type with a light that goes on when your goal is met ! way cool, but how much??
cas3 is offline   Reply With Quote
Old 03-20-2017, 09:57 PM   #20
cmbrucew
Senior Member
 
cmbrucew's Avatar
 
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,063
Default Re: Torque wrench

I replaced a beam with a Proto clicker, middle 70s, and bought Snap on 1/4" and 3/8".
I trust the old Proto. Used it with torque multipliers on a lot of stuff.
Bruce
__________________
Works good
Lasts long time
cmbrucew is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:51 AM.