Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-24-2019, 11:32 AM   #21
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,947
Default Re: Clutch pedal

Pressure plate action CAN be adjusted.
J Franklin is offline   Reply With Quote
Old 07-24-2019, 09:09 PM   #22
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

Here's what I found out tonight. I took the trans out and checked finger adjustments. They were way off. I had them with in .002 when I started. They went out of adjustment. Just by pushing in clutch. I did tap on them after adjusting them and rechecked them. Changed plate with another new one that came with car. They both look like they came from the same place. Checked fingers on it and they were out. Didn't adjust them and had the same result. Took it back apart. Measured the dish in flywheel. It is at 1.125 deep. Tried to find spec in Les Anderson book. Didn't see it but did find standard disc is supposed to be. 340. Mine is .400. Thought maybe that.060 is making the pedal have to move down far to release the clutch. I did check the throw out bearing shaft and it is the correct one. I think I will order a rebuilt clutch and disc from Bert's tomorrow. Does this sound like a good plan.? You guys have been a tremendous help so far. A lot of good advise. Thank you.
bmodeltman is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-25-2019, 01:41 PM   #23
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: Clutch pedal

Through the mist I smell a clutch disc in backwards. if the fingers are leaning way in towards the pilot bearing and it won't release, that can happen. I'm thinking that it is hard to do it wrong on an A. And now I read the above post and retract the disc flip scenario. Been looking for the spec. on depth, recess, friction surface to shoulder at flywheel. Cant find it now, sorry.

Last edited by 100IH; 07-25-2019 at 02:09 PM.
100IH is offline   Reply With Quote
Old 07-25-2019, 03:54 PM   #24
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

I did check disc and it was install correct. I'm going to experiment with the fingers at 3/4. If the fingers are closer to the disc and I adjust at pedal it should release higher on the pedal. Either way I did find out it is the disc with the springs that can come out. I still want to get a better disc and.pressure plate. I will try the 3/4 finger adjustment to see what happens
bmodeltman is offline   Reply With Quote
Old 07-25-2019, 08:14 PM   #25
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

I tried the 3/4 adjustment on the fingers and it made no difference. I tried an original wore out pressure plate.and.still.the same. The only thing I haven't changed yet is the disc. I only have this one that is .400 thick. Les Anderson says it's supposed to be.340. These new parts I have are at least 30 year old reproductions. This car has been apart at least that long.
bmodeltman is offline   Reply With Quote
Old 07-26-2019, 06:35 AM   #26
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Clutch pedal

Sponsored Links (Register now to hide all advertisements)
Your 1.125" recess in the flywheel is fine. I recall someone posting the spec as 1.123".
Set the fingers to 11/16" after the new disc and pressure plate are installed.
Tom Wesenberg is offline   Reply With Quote
Old 07-26-2019, 10:13 AM   #27
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,713
Default Re: Clutch pedal

Any chance you have a AA throw out bearing hub?


Bob
Attached Images
File Type: jpeg attachment.php.jpeg (5.6 KB, 122 views)
Bob C is offline   Reply With Quote
Old 07-26-2019, 01:28 PM   #28
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

It does have the correct hub. Could I have the wrong clutch arm? How could I tell if it's right?
bmodeltman is offline   Reply With Quote
Old 07-26-2019, 02:09 PM   #29
1955cj5
Senior Member
 
1955cj5's Avatar
 
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,576
Default Re: Clutch pedal

Do you have a picture?

Here is a picture of my old repaired arm and the new replacement....sorry no measurement right now...
Attached Images
File Type: jpg 2015_0814modelajeep1442.jpg (106.4 KB, 17 views)
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62
1955cj5 is offline   Reply With Quote
Old 07-26-2019, 09:34 PM   #30
oldbird55
Member
 
Join Date: Mar 2013
Location: e tenn
Posts: 63
Default Re: Clutch pedal

Should I be able to push the clutch arm up by hand.
oldbird55 is offline   Reply With Quote
Old 07-27-2019, 05:14 AM   #31
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

I can push the pedal down by hand when all is hooked up but but not the arm it's self
bmodeltman is offline   Reply With Quote
Old 07-27-2019, 05:17 AM   #32
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

It moves by hand until it gets to the fingers on the pressure plate
bmodeltman is offline   Reply With Quote
Old 07-27-2019, 07:43 PM   #33
oldbird55
Member
 
Join Date: Mar 2013
Location: e tenn
Posts: 63
Default Re: Clutch pedal

thanks
oldbird55 is offline   Reply With Quote
Old 07-29-2019, 09:51 PM   #34
bmodeltman
Member
 
Join Date: Nov 2010
Posts: 33
Default Re: Clutch pedal

I think I have my clutch issue solved. I got a new collar and found the old one was messed with before. The new collar brought the pedal up to 1/2 inch to being even with the brake pedal. I heated the clutch pedal and got it level with brake pedal. Also got a new clutch disc and pressure plate. Checked the new disc and it was .380 which was .020 thinner than the old disc. Checked the finger adjustment and put it together. Now the pedal feels good and disengages way before it hits the engine mount. All the small adjustments added to a lot at the top of the pedal. I want to thank everyone for their help. I sure did learn a lot.
bmodeltman is offline   Reply With Quote
Old 07-29-2019, 10:21 PM   #35
t farr
Member
 
Join Date: Jun 2010
Location: Auckland New Zealand
Posts: 32
Default Re: Clutch pedal

I had the wrong ones previously fitted and didn't work well, changed it and no more problems with it.
t farr is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:55 AM.