|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-02-2020, 07:05 PM | #1 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
New gaskets - cardboard
Hey guys, I got a few new gaskets sets for trans, steering box, Speedo...... They are made in China with what appears to be cardboard/ cereal boxes. I've read on here guys saying to only use gasket sealant if the mating surface has issues or the gasket leaks. With this cardboard, do you think they will seal fine or should gasket sealant/ dressing be used?
|
06-02-2020, 07:25 PM | #2 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: New gaskets - cardboard
Question, where did the gaskets come from? If not a reliable source I would suggest talking to someone like Mac VanPelt or 3rd Generation and getting better parts. I don't think you are going to like it if you have to pull it and redo it later if there is an issue. The steering box gasket have to be specific sizes to set the bearing loads.
|
Sponsored Links (Register now to hide all advertisements) |
|
06-02-2020, 07:54 PM | #3 | |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
Re: New gaskets - cardboard
Quote:
Yes, trying to avoid doing it all again, not that practice isn't good... Unfortunately Mac auto parts. I tagged them onto an existing order. They had Denise carpenter logo covered up on the packaging. The steering box top gasket is thick and appears solid but the multiple smaller gaskets to set bearing load are thin brown paper. At least my banjo gaskets are made by Best gasket. |
|
06-02-2020, 08:09 PM | #4 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: New gaskets - cardboard
>>>I've read on here guys saying to only use gasket sealant if the mating surface>>>
They look fine. If they were mine, I'd use wheel bearing grease for the sealant. Jack E/NJ |
06-02-2020, 08:34 PM | #5 |
Senior Member
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,064
|
Re: New gaskets - cardboard
I have made good gaskets from the sleeve Victor head gaskets came in. Good clean mating surfaces is the key.
Bruce
__________________
Works good Lasts long time |
06-02-2020, 09:20 PM | #6 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,969
|
Re: New gaskets - cardboard
Sponsored Links (Register now to hide all advertisements)
|
06-02-2020, 10:02 PM | #7 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,584
|
Re: New gaskets - cardboard
some folks accuse me of liking beer, but really, i just need the boxes for making patterns and occasionally gaskets.
|
06-02-2020, 11:09 PM | #8 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,975
|
Re: New gaskets - cardboard
Those look completely legit and usable. If they dyed the stock red or some other color you wouldn't be skeptical.
|
06-02-2020, 11:11 PM | #9 |
Senior Member
Join Date: Oct 2011
Location: elmira,ny
Posts: 1,518
|
Re: New gaskets - cardboard
we used to use brown paper bags for thin gaskets. never leaked.
|
06-03-2020, 12:53 AM | #10 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
Re: New gaskets - cardboard
|
06-03-2020, 12:59 AM | #11 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
Re: New gaskets - cardboard
So just some grease, no permatex sealant/ dressing or such needed?
|
06-03-2020, 06:49 AM | #12 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,635
|
Re: New gaskets - cardboard
For me it would depend on the surfaces........if both sides are smooth and flat, I’d use grease....any rough parts or if I questioned a smooth fit....a LITTLE permatex.....Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
06-03-2020, 11:49 AM | #13 |
Senior Member
Join Date: May 2010
Location: Lakeland Florida
Posts: 304
|
Re: New gaskets - cardboard
The thin gaskets are for setting the bearing preload. Do not use gasket sealer.
|
06-03-2020, 01:48 PM | #14 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: New gaskets - cardboard
You need to be careful using gasket sealer on any application where it can be squeezed into places it can do harm!
|
06-03-2020, 06:18 PM | #15 |
Senior Member
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,064
|
Re: New gaskets - cardboard
My auto shop instructor, said 60 years ago. a little permatex on the removable part only, to hold the gasket during assembly. Makes life easier when you next work on it.
Bruce
__________________
Works good Lasts long time |
06-03-2020, 06:25 PM | #16 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,333
|
Re: New gaskets - cardboard
I have been using cereal boxes for gasket material since at least 1957.
|
06-03-2020, 07:54 PM | #17 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
Re: New gaskets - cardboard
Thank you for all the input.
|
06-04-2020, 09:34 PM | #18 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,981
|
Re: New gaskets - cardboard
I save the backing on a yellow legal tablet for gaskets. The shiny side of cereal boxes, like where it says 'wheaties' always seemed like it wouldn't seal as well as the porous side. The legal cardboard IS a bit thick for some applications, so I like the brown paper bag suggestion..
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1946 Tonner Pickup with 226 H six, 1979 Toyota landcruiser wagon, now wearing 1947 Ford Jailbar sheet metal. 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
06-05-2020, 01:42 AM | #19 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,063
|
Re: New gaskets - cardboard
You can get stock sheets of gasket material from napa, packs with cork and versions sizes and material. It's nice to have on hand if you do a service or want to replace certain little things. It takes a bit of time to cut out with a exacto knife and using a fuel line punch for holes. But not a big deal really. Depending on material a bit of oil or perm spray goes a long way. RTV gooping is overkill. In my thinking.
Looks like a good set of gasket you have. Don't over think it. Use them. Oil will get to them if they need it. Dry install. Last edited by Tinker; 06-05-2020 at 01:48 AM. |
06-05-2020, 01:50 AM | #20 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,063
|
Re: New gaskets - cardboard
Think you are complaining to just complain. Look like great gaskets to me! Not sure how you set bearing/worm load on a steering box with a gasket?
Last edited by Tinker; 06-05-2020 at 01:56 AM. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|