|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
06-04-2017, 09:25 AM | #1 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 580
|
Removing ridge from cylinders
It appears that I must have steel sleeves in my 1937 flathead. My ridge reamer will not cut the ridge. Any suggestions on how to remove the ridge to get the pistons out? thanks
|
06-04-2017, 10:41 AM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,936
|
Re: Removing ridge from cylinders
Just wondering why your ridge reamer won't do the job?
Can you post a photo of your reamer and ridge set up? |
Sponsored Links (Register now to hide all advertisements) |
|
06-04-2017, 12:01 PM | #3 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 580
|
Re: Removing ridge from cylinders
I have ordered a new carbide cutter for the reamer but haven't received it. Thanks
|
06-04-2017, 12:12 PM | #4 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Removing ridge from cylinders
The sleeves are too hard for a ridge reamer.
I have to ask: If you have ridges, why are you worried about removing them? It's obvious the bores are worn too far to simply replace rings and machine work is necessary. If you are attempting to salvage the pistons from an otherwise poor block, use a small die grinder to cut away the ridges.
__________________
"I can explain it for you. However, I can't understand it for you". |
06-04-2017, 12:59 PM | #5 |
Senior Member
Join Date: Sep 2010
Location: Independence, VA
Posts: 423
|
Re: Removing ridge from cylinders
What you have in your hand is a HONE,,,what ever the package says.
|
06-04-2017, 02:47 PM | #6 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Removing ridge from cylinders
Sponsored Links (Register now to hide all advertisements)
|
06-04-2017, 02:55 PM | #7 |
Senior Member
Join Date: May 2010
Location: Reseda, Calif.
Posts: 2,188
|
Re: Removing ridge from cylinders
Me to. Not a hone.
|
06-04-2017, 03:28 PM | #8 |
Senior Member
Join Date: Sep 2010
Location: Independence, VA
Posts: 423
|
Re: Removing ridge from cylinders
OK,,,,,,,,,,never seen one like that,,,
|
06-04-2017, 03:52 PM | #9 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,064
|
Re: Removing ridge from cylinders
I haven't used one in years . . . and don't see much of a purpose as when the cylinder is that worn, I'll rebore it to a larger size . . . or put new sleeves in it. Have you measured the bores to figure out how worn they are?
|
06-04-2017, 04:47 PM | #10 |
Senior Member
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,096
|
Re: Removing ridge from cylinders
Just a guess , he wants to resleeve and reuse Pistons . No sense in busting up some Pistons that may have a new home .
|
06-04-2017, 05:39 PM | #11 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Removing ridge from cylinders
If sleeves are that worn it is hard to believe the pistons are usable.
|
06-05-2017, 07:50 AM | #12 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Removing ridge from cylinders
Quote:
Of course, from what I read on the Barn and other forums, most guys don't really "rebuild", at least not correctly.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
06-04-2017, 08:48 PM | #13 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: Removing ridge from cylinders
At the very least, the ring lands will be worn.
|
06-04-2017, 09:02 PM | #14 |
Senior Member
Join Date: May 2010
Location: Mt. Holly,NJ
Posts: 1,822
|
Re: Removing ridge from cylinders
Steel sleeves and aluminum pistons. Which is going to wear the most?
|
06-04-2017, 09:28 PM | #15 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: Removing ridge from cylinders
V12Bill>>>Steel sleeves and aluminum pistons. Which is going to wear the most>>>
Hmmm? Sounds like a trick question. I'll guess the sleeves the most. The pistons least. And the rings in between. Did I guess right? 8^) Jack E/NJ |
06-05-2017, 08:02 AM | #16 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: Removing ridge from cylinders
I believe the pistons used with the steel liners were also steel.
|
06-05-2017, 08:07 AM | #17 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,064
|
Re: Removing ridge from cylinders
I looked at the pictures that were posted earlier - pretty heavy ridge is visible. The sleeves look like the ole' "tin can sleeves" that Ford would put in many of their early 24 stud - 221 cubic inch Ford engines (though I didn't know they did it back in 37 - maybe a later 'rebuild'???).
Me, I would look for a new set of sleeves and associated pistons/rings . . . and rebuild it to tip-top shape. With that said, I'm not trying to spend your money - just talking about the best way to do the job. Best of luck, B&S |
06-05-2017, 09:09 AM | #18 |
Senior Member
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,776
|
Re: Removing ridge from cylinders
Go borrow one from Autozone and see it will do the job.
|
06-05-2017, 09:35 AM | #19 |
Senior Member
Join Date: May 2010
Location: Mt. Holly,NJ
Posts: 1,822
|
Re: Removing ridge from cylinders
Remove sleeves and bore to 239 CID
|
06-05-2017, 10:03 AM | #20 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Removing ridge from cylinders
I've done that and wow, well worth it. And, from my experience I got a stronger engine with less of an investment than R&R sleeves.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
|
Sponsored Links (Register now to hide all advertisements) |
|