Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-17-2020, 07:03 PM   #1
Cape Codder
Senior Member
 
Cape Codder's Avatar
 
Join Date: May 2010
Posts: 1,261
Default Seat Belt

Has anyone considered removing most of the wood in door post, both Tudor & Fordor, installing a very thick piece of steel with a taped hole for the seat belt attachment, then a small amount of wood. This could be a shoulder type belt!

Any comments, of course both Pro's & Con's.
Cape Codder is offline   Reply With Quote
Old 03-18-2020, 09:19 AM   #2
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,486
Default Re: Seat Belt

Quote:
Originally Posted by Cape Codder View Post
Has anyone considered removing most of the wood in door post, both Tudor & Fordor, installing a very thick piece of steel with a taped hole for the seat belt attachment, then a small amount of wood. This could be a shoulder type belt!

Any comments, of course both Pro's & Con's.
No real need. If the wood is solid, just fab an anchor plate and recess it into the wood.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-18-2020, 09:42 AM   #3
cjkohnast
Senior Member
 
Join Date: Jan 2017
Posts: 357
Default Re: Seat Belt

I put a 2x2 steel behind the door post of my pick up mounted seat and shoulder belt and belt retractor .
cjkohnast is offline   Reply With Quote
Old 03-18-2020, 09:51 AM   #4
Roxo
Senior Member
 
Roxo's Avatar
 
Join Date: Nov 2018
Location: Kankakee, Illinois
Posts: 225
Default Re: Seat Belt

Mounting on wood is fine. But if your in a accident I would trust steel over wood anyday.
Roxo is offline   Reply With Quote
Old 03-18-2020, 09:59 AM   #5
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,486
Default Re: Seat Belt

Quote:
Originally Posted by Roxo View Post
Mounting on wood is fine. But if your in a accident I would trust steel over wood anyday.
What are your expectations with the shoulder belt if you are in an accident? The lap belt will take the majority of the G-forces of the occupant. I would be more concerned with being able to securely anchor the lap belts instead of the shoulder restraint.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 03-18-2020, 05:01 PM   #6
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: Seat Belt

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Roxo View Post
Mounting on wood is fine. But if your in a accident I would trust steel over wood anyday.
Mounting a seat belt to wood is not allowed here, even with some of the best woods in the world for that kind of use. Even the requirements for mounting to steel are very stringent.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 03-18-2020, 08:46 PM   #7
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: Seat Belt

I didn't want to cut my car up so I put a bolt in cage in when I was doing autocross, hillclimbs and rally's. There's no part of the original structure strong enough for legal belts.
Pete is online now   Reply With Quote
Old 03-18-2020, 10:36 PM   #8
30Murray
Senior Member
 
Join Date: Jun 2010
Location: Vancouver B.C.
Posts: 103
Default Re: Seat Belt

When installing seat belts you should consider the government design requirements when making the attachment points. The structural components of a pelvic restraint must each withstand a force of 2500 lbs. and the upper restraint (shoulder belt) a force of 1500 lbs. These are Canadian standards but US are probably the same. Obviously we can't design and test a compliant system, but at least build something that will give a reasonable level of safety over nothing at all.


I thought about cutting a slot in the door post of my Fordor for a steel bar also, but decided it was impractical and not strong enough. Instead I put a steel brace across the roof and attached the shoulder belts to angle iron brackets at each end. You can sort of see it in this picture. The force would pull down and forward. At best, I think my 3-point belts might reduce injuries in a low speed collision in a car never designed with passenger safety in mind. I hope I never have to test it.

I don't think my picture showed up - I posted one a few years ago, try a search for "seat belts" or "shoulder belts"


Last edited by 30Murray; 03-18-2020 at 10:40 PM. Reason: no photo?
30Murray is offline   Reply With Quote
Old 03-18-2020, 10:47 PM   #9
30Murray
Senior Member
 
Join Date: Jun 2010
Location: Vancouver B.C.
Posts: 103
Default Re: Seat Belt

Trying photo again...
Attached Images
File Type: jpg Resize of Shoulder belt.jpg (18.2 KB, 207 views)
30Murray is offline   Reply With Quote
Old 03-19-2020, 08:55 AM   #10
V4F
Senior Member
 
V4F's Avatar
 
Join Date: May 2010
Location: ca.
Posts: 2,522
Default Re: Seat Belt

mine are bolted to the floor behind the seat
__________________
V4f
V4F is offline   Reply With Quote
Old 06-06-2020, 01:31 PM   #11
DNLs1930
Senior Member
 
DNLs1930's Avatar
 
Join Date: May 2019
Location: Fort Worth side of DFW
Posts: 171
Default Re: Seat Belt

Quote:
Originally Posted by V4F View Post
mine are bolted to the floor behind the seat
Your shoulder harness is also bolted to the floor? That was my first thought but have seen the steel plate idea in the side pillar so just wondering which way to go. I think the floor idea would be easier "mounting" I just wonder how the belt would hold as the seat starts to move in a crash.
DNLs1930 is offline   Reply With Quote
Old 06-19-2020, 10:58 PM   #12
Lona
Senior Member
 
Lona's Avatar
 
Join Date: Dec 2013
Location: Gloucester, Va
Posts: 464
Default Re: Seat Belt

1. There is no way a shoulder belt attached to a wood pillar or even to a piece of steel recessed into a wood pillar will not tear out even in a slow speed front end collision.

2. Mounting a shoulder belt to the floor directly behind the seat is a bad idea. In a frontal collision, your body will violently move forward, forcing the shoulder belt downward with a force enough to crush your spine. With no suitably strong door pillar in our cars, the best location in a tudor or four door sedan is at the floor behind the rear seat. In a coupe or roadster, the attachment point would be horizontal from the top of the seat back into the trunk or rumble seat compartment.

I have installed shoulder belts in three of my antique cars with documentation and photos on this forum. I do not know how to post a link to them but using the search function, you should be able to access the posts if interested.

Glen
__________________
'31 Model A Deluxe Roadster
'31 Chrysler Model 70 Sedan
'88 Pontiac Fiero GT
'36 Auburn Boattail Speedster replica
Lona is offline   Reply With Quote
Old 06-19-2020, 11:22 PM   #13
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Seat Belt

I think this is the thread Lona is referring to?

https://www.fordbarn.com/forum/showthread.php?p=847774
Y-Blockhead is offline   Reply With Quote
Old 06-20-2020, 06:54 AM   #14
Lona
Senior Member
 
Lona's Avatar
 
Join Date: Dec 2013
Location: Gloucester, Va
Posts: 464
Default Re: Seat Belt

Quote:
Originally Posted by Y-Blockhead View Post
I think this is the thread Lona is referring to?

https://www.fordbarn.com/forum/showthread.php?p=847774
Thanks for you help in showing a link to the roadster 3-point belt installation. There is also another post on installing retractable 3-point seat belts in a sedan if you would be kind enough to post a link to that too.

Glen
__________________
'31 Model A Deluxe Roadster
'31 Chrysler Model 70 Sedan
'88 Pontiac Fiero GT
'36 Auburn Boattail Speedster replica
Lona is offline   Reply With Quote
Old 06-20-2020, 11:11 AM   #15
mike657894
Senior Member
 
mike657894's Avatar
 
Join Date: Oct 2015
Location: Bay City Michigan
Posts: 1,050
Default Re: Seat Belt

I have three points belts in my fordor attached to the door post. seemed a better idea than none at all. i have experienced roll overs in moderns at low speed. locally two young guys died in a slow speed no belt van crash. broke both their necks.
mike657894 is offline   Reply With Quote
Old 06-20-2020, 05:33 PM   #16
Keeper79
Member
 
Keeper79's Avatar
 
Join Date: Jul 2011
Location: In the Sticks of Virginia
Posts: 62
Default Re: Seat Belt

Have thought about possible installation of seat belts. Even with it being an open top Deluxe Roadster I don't see more than lap belts being used.

The other flip of the coin is why mess with it. I ride motorcycles on the street and do track days were you hit 140+ mph every single lap.

At this point I should look at my guardian angel and see what condition they are in.
Keeper79 is offline   Reply With Quote
Old 06-20-2020, 10:11 PM   #17
Lona
Senior Member
 
Lona's Avatar
 
Join Date: Dec 2013
Location: Gloucester, Va
Posts: 464
Default Re: Seat Belt

Quote:
Originally Posted by Keeper79 View Post
Have thought about possible installation of seat belts. Even with it being an open top Deluxe Roadster I don't see more than lap belts being used.

The other flip of the coin is why mess with it. I ride motorcycles on the street and do track days were you hit 140+ mph every single lap.

At this point I should look at my guardian angel and see what condition they are in.
lap belts only may keep you in the car but your upper body will rotate around the belt and your head will hit the steering wheel or the windshield. If you are installing lap belts, why not spend a little extra time and install shoulder restraints at the same time.

Glen
__________________
'31 Model A Deluxe Roadster
'31 Chrysler Model 70 Sedan
'88 Pontiac Fiero GT
'36 Auburn Boattail Speedster replica
Lona is offline   Reply With Quote
Old 06-20-2020, 11:29 PM   #18
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Seat Belt

Quote:
Originally Posted by Lona View Post
Thanks for you help in showing a link to the roadster 3-point belt installation. There is also another post on installing retractable 3-point seat belts in a sedan if you would be kind enough to post a link to that too.

Glen
I think I found it... finally!

https://www.fordbarn.com/forum/showt...at+belts+sedan

Quote:
Originally Posted by Keeper79 View Post
Have thought about possible installation of seat belts. Even with it being an open top Deluxe Roadster I don't see more than lap belts being used.

The other flip of the coin is why mess with it.
Maybe for the protection of your passengers?
Y-Blockhead is offline   Reply With Quote
Old 06-21-2020, 06:52 AM   #19
Lona
Senior Member
 
Lona's Avatar
 
Join Date: Dec 2013
Location: Gloucester, Va
Posts: 464
Default Re: Seat Belt

Y-Blockhead,

Thanks again for your help in posting the link to my second description on how to install three point seat belts in a sedan. I would be most appreciative if you could PM me on how you make a link like that so I will be able to do it in the future.

Glen
__________________
'31 Model A Deluxe Roadster
'31 Chrysler Model 70 Sedan
'88 Pontiac Fiero GT
'36 Auburn Boattail Speedster replica
Lona is offline   Reply With Quote
Old 06-21-2020, 07:17 AM   #20
1crosscut
Senior Member
 
1crosscut's Avatar
 
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,905
Default Re: Seat Belt

Quote:
Originally Posted by Lona View Post
Y-Blockhead,

Thanks again for your help in posting the link to my second description on how to install three point seat belts in a sedan. I would be most appreciative if you could PM me on how you make a link like that so I will be able to do it in the future.

Glen
Here is how I paste a link into a post.

Using my mouse I put the cursor at the beginning of the address in the address bar, hold down the clicker and drag it across to the end of the address. Doing this will highlight it.

Then I press and hold down the Ctrl button and then press the C button.
This will copy anything that is highlighted.

Then I place my cursor at the point in what ever document I'm in at the point I want it to appear.

Then I press and hold the Ctrl button and press the V button.

Poof... there it is.


Works with any address, text etc... you want to copy and paste.
__________________
Dave / Lincoln Nebraska
1crosscut is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:19 PM.