The Ford Barn

BUBBAS IGNITION · 07-01-2013, 10:53 AM

We have all been there !!!

DO NOT TIGHTEN BOLT WITH MISALIGNED CAMSHAFT???
OR
DO NOT DROP!!

Vic Piano · 07-01-2013, 10:59 AM

Looks like its time for a JB Weld roadside repair...

Fourdy · 07-01-2013, 11:05 AM

WHY??? LOL

Fourdy

Mart · 07-01-2013, 11:38 AM

Ah! the old two-bolt three bolt.

Ol' Ron · 07-01-2013, 03:44 PM

Been there, done that, Waz young once too.

Bluebell · 07-01-2013, 07:21 PM

Sponsored Links (Register now to hide all advertisements)

Mart, are you holding back on something?

Lawson Cox · 07-01-2013, 09:31 PM

Bubba: Looks like someone beat it to death with a hammer trying to get it unstuck from the front of the engine. Look at all of that gasket goop. LOL

FLA48 · 07-01-2013, 09:35 PM

Looks like something I would do.

BILL WZOREK · 07-02-2013, 04:12 AM

Yea / Yea / Yea but can you fix it ? LOL

Or -- YEA I did send you a core for core credit !!!!! LOL

Rowdy · 07-02-2013, 09:56 AM

I pitched a couple of them like that last year while sorting through the ones I have accumulated over time. I wish I knew the cause. Atleast when done sorting I found 3 for the the 3 for 1 trade. Rod

07-01-2013, 10:59 AM	#2
Vic Piano Senior Member Join Date: May 2010 Location: Odessa, FL Posts: 7,611	Re: Monday morning helmet....... Looks like its time for a JB Weld roadside repair... __________________ Imagination is more important than knowledge.

07-01-2013, 11:05 AM	#3
Fourdy Senior Member Join Date: May 2010 Location: Port Townsend, WA Posts: 601	Re: Monday morning helmet....... WHY??? LOL Fourdy __________________ My 24 T https://fordbarn.com/forum/showthread...ghlight=fourdy

07-01-2013, 11:38 AM	#4
Mart Senior Member Join Date: May 2010 Location: Solihull, England. Posts: 8,755	Re: Monday morning helmet....... Ah! the old two-bolt three bolt.

07-01-2013, 03:44 PM	#5
Ol' Ron Senior Member Join Date: May 2010 Location: Chester Vt Posts: 8,860	Re: Monday morning helmet....... Been there, done that, Waz young once too.

07-01-2013, 07:21 PM	#6
Bluebell Senior Member Join Date: Nov 2012 Location: Tauranga, New Zealand Posts: 726	Re: Monday morning helmet....... Sponsored Links (Register now to hide all advertisements) Mart, are you holding back on something?

07-01-2013, 09:31 PM	#7
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 7,009	Re: Monday morning helmet....... Bubba: Looks like someone beat it to death with a hammer trying to get it unstuck from the front of the engine. Look at all of that gasket goop. LOL __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".

07-01-2013, 09:35 PM	#8
FLA48 Senior Member Join Date: Jul 2011 Location: Conroe TX Posts: 170	Re: Monday morning helmet....... Looks like something I would do.

07-02-2013, 04:12 AM	#9
BILL WZOREK Senior Member Join Date: May 2010 Location: Florence Ma. Posts: 2,404	Re: Monday morning helmet....... Yea / Yea / Yea but can you fix it ? LOL Or -- YEA I did send you a core for core credit !!!!! LOL

07-02-2013, 09:56 AM	#10
Rowdy BANNED Join Date: May 2010 Location: Gothenburg Nebraska Just off I-80 Posts: 4,893	Re: Monday morning helmet....... I pitched a couple of them like that last year while sorting through the ones I have accumulated over time. I wish I knew the cause. Atleast when done sorting I found 3 for the the 3 for 1 trade. Rod __________________ Do the RIGHT thing - Support the H.A.M.B. Alliance!!!!