|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-31-2017, 05:30 PM | #1 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Rear main drain on 37 thread size
Drain tube didn't come on my 37 engine as original,as I have been reading but would.ike to put one there,any one know thread size in cap ?
__________________
DON P |
10-31-2017, 06:21 PM | #2 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,218
|
Re: Rear main drain on 37 thread size
Maybe 1/4 npt
Lawrie |
Sponsored Links (Register now to hide all advertisements) |
|
10-31-2017, 06:29 PM | #3 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: Rear main drain on 37 thread size
Nope,looks like 24 tpi. by 7/16, no sure tho
__________________
DON P |
10-31-2017, 07:04 PM | #4 |
Senior Member
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
|
Re: Rear main drain on 37 thread size
Does anyone put that tube back on ??
__________________
"Came too close to dying to stop living now!" |
10-31-2017, 07:15 PM | #5 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: Rear main drain on 37 thread size
From what I read,it's not needed but it won't hurt to have it there,after oil pan was vented oil is not supposed to pressure out the rear seal or labrith ring,
__________________
DON P |
11-01-2017, 01:50 AM | #6 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: Rear main drain on 37 thread size
Sponsored Links (Register now to hide all advertisements)
Blowby still goes out there and the vent without it, ford probably saved some money and it worked without it. The heavy truck engines seems to have used it longer looking at the engines i break apart and some have a S shaped version with a checkvalve to prevent oil going out climbing steep hills. I use them as i like the engineering idee of it. |
11-01-2017, 08:52 AM | #7 |
Senior Member
Join Date: Jul 2010
Posts: 2,593
|
Re: Rear main drain on 37 thread size
I like um to, I believe the idea was to keep some of the Crankcase windage blowing oil in the slinger area out into the clutch housing.
Martin. |
11-01-2017, 09:49 AM | #8 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: Rear main drain on 37 thread size
This has been REALLY BEAT TO DEATH in the past here .
That said has anyone watched a V8 [ or whatever ] with a clear oil pan run as a demo ? Why would you not want even a short one to keep some of that splashing oil OUT of the rear seal area ? I only use actual 33-34 non-vented motors and it is definitely a help with those . |
11-01-2017, 10:28 PM | #9 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,834
|
Re: Rear main drain on 37 thread size
Don, just measured one up as best I could and believe it to be 1/2"x 32 TPI
__________________
Unfortunately, two half wits don't make a whole wit! |
11-02-2017, 09:08 AM | #10 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: Rear main drain on 37 thread size
Pipe is for sure 1/2" with a wall thickness of .042" .
The pics blow up pretty good . [ QUOTE=Brian;1546909]Don, just measured one up as best I could and believe it to be 1/2"x 32 TPI[/QUOTE] |
11-04-2017, 06:20 PM | #11 |
Senior Member
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,361
|
Re: Rear main drain on 37 thread size
We have some that are essentially straight but with a slight bend at one end. The threads are confirmed as 32 tpi. The odd thing is that the bend is at the unthreaded end......opposite of the ones pictured above.
__________________
VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com |
11-04-2017, 07:18 PM | #12 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: Rear main drain on 37 thread size
Got one in mail today,your correct,32 tpi by about 1/2 but only 1 1/2 in long,would like to put a 45 on it and extend it below oil level.
__________________
DON P |
11-04-2017, 07:34 PM | #13 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: Rear main drain on 37 thread size
Solder a copper pipe onto it . The ones above are NOS
|
11-04-2017, 09:04 PM | #14 |
Junior Member
Join Date: Jun 2012
Location: St.rt. 141 Ironton Ohio
Posts: 4
|
Re: Rear main drain on 37 thread size
Don bring the one you have over to the shop ,we will make one any length.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|