Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-06-2016, 01:01 PM   #1
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default 1940 Ford convertible body tags

I'd like to hear from guys with '40 Ford convertibles...
Is there or, to your knowledge, was there, a body tag on your vehicle? Or, are there numbers stamped in to the firewall?
I have posted two photos below that allow a glimpse of where a tag should have been and a glimpse as to where numbers may have been stamped.
Please, if you are able to respond, allow as much as you know in regard to your vehicles 'pedigree".

The tag was "nailed" to the upper- left corner of the firewall. Stamping was below the voltage regulator.

thanks!!!
Attached Images
File Type: jpg DSCN1055.jpg (73.6 KB, 444 views)
File Type: jpg body umber stamped.jpg (60.1 KB, 169 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 03-06-2016, 02:09 PM   #2
Ken/Alabama
Senior Member
 
Ken/Alabama's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 3,237
Default Re: 1940 Ford convertible body tags

Mine had a tag. I didn't reinstall it because at the time when I built that car I wasn't very concerned with being too correct. I still have it somewhere.
Ken/Alabama is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-06-2016, 04:27 PM   #3
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Ken/Alabama View Post
Mine had a tag. I didn't reinstall it because at the time when I built that car I wasn't very concerned with being too correct. I still have it somewhere.
Thanks Ken. That's one response. C'mon guys... please....
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 03-06-2016, 04:47 PM   #4
Bill
Senior Member
 
Bill's Avatar
 
Join Date: May 2010
Location: Nova Scotia
Posts: 469
Default Re: 1940 Ford convertible body tags

Is it possible that those convs with the tag would also have the stamped # under the voltage regulator? Just asking. Bill
Bill is offline   Reply With Quote
Old 03-06-2016, 05:26 PM   #5
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Bill View Post
Is it possible that those convs with the tag would also have the stamped # under the voltage regulator? Just asking. Bill
Not sure Bill. I have only heard "hearsay" about the cowls being stamped. Documents indicate a body tag was to be attached. I am attempting to find out what in reality happened back then.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 03-06-2016, 07:42 PM   #6
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: 1940 Ford convertible body tags

Sponsored Links (Register now to hide all advertisements)
No tag, no stamped number. VIN * 18-5712258 *
I am the first owner of this car outside of the family that bought it new.

Anybody else?
deuce_roadster is offline   Reply With Quote
Old 03-07-2016, 08:21 PM   #7
KSFORTYFORDS
Member
 
KSFORTYFORDS's Avatar
 
Join Date: May 2010
Location: Hays, KS
Posts: 57
Default Re: 1940 Ford convertible body tags

Mine has a body tag on it, the car was partially restored when I bought it out of Minnesota in 2006.
KSFORTYFORDS is offline   Reply With Quote
Old 03-15-2016, 06:54 PM   #8
Milt/Las Vegas
Senior Member
 
Milt/Las Vegas's Avatar
 
Join Date: May 2010
Location: North Las Vegas,Nv/Rainier,Or
Posts: 450
Default Re: 1940 Ford convertible body tags

I checked the convertible project which has the original paint on the firewall no tag never had one and no stamping underneath the voltage regulator.They all have the holes for the tag but no tags.The other 40 convertible I'm building which was a pretty original complete car had no tag and the firewall wasn't stamped.
__________________
Milt/Las Vegas

Last edited by Milt/Las Vegas; 03-15-2016 at 07:09 PM. Reason: More info
Milt/Las Vegas is offline   Reply With Quote
Old 02-11-2019, 11:26 AM   #9
Automotive Stud
Senior Member
 
Automotive Stud's Avatar
 
Join Date: May 2010
Location: New Jersey
Posts: 831
Default Re: 1940 Ford convertible body tags

I know this is old, but for what it's worth I just saw the thread and checked my car. There is no tag and no signs of there being a tag. My car has the original paint on the firewall.
Automotive Stud is offline   Reply With Quote
Old 04-17-2021, 10:18 PM   #10
woodiedude
Junior Member
 
woodiedude's Avatar
 
Join Date: Oct 2020
Location: Las Vegas Nevada
Posts: 16
Default Re: 1940 Ford convertible body tags

I recently acquired a 40 Convertible and I saw this post. I am new to the group but I will try to attach a picture of my engine that has a body tag mounted with four nails. The tag has been painted over and I didn’t try to remove any of the paint. I can get more pictures if needed next week.
Attached Images
File Type: jpg 3DF9E9A1-A2A3-4CDC-9718-636491A72FF1.jpg (42.7 KB, 100 views)
File Type: jpeg 697E3B49-2167-4CAF-99D5-F1339C899092.jpeg (133.5 KB, 107 views)
File Type: jpg 2B7096D1-E4BB-4365-9E16-B7BC99D35238.jpg (42.6 KB, 90 views)
woodiedude is offline   Reply With Quote
Old 04-18-2021, 04:43 AM   #11
swoopNZ
MEMBER EMERITUS
 
Join Date: May 2010
Location: New Zealand
Posts: 1,380
Default Re: 1940 Ford convertible body tags

One of my 39 deluxe convertibles ( ex USA ) had a body tag up in the LH corner.
From memory it ended with 074 indicating the first week of production.
swoopNZ is offline   Reply With Quote
Old 04-18-2021, 06:28 AM   #12
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 4,725
Default Re: 1940 Ford convertible body tags

Like woodiedude in #10 above here is another early firewall you can see the four holes for mounting the patent data plate over the hand throttle bump out, on the vertical surface. Ill ask the mechanic if there are numbers or a body tag.
The mechanic says there are no numbers on the firewall. The old paint was stripped for repaint so any numbers would have been seen.
Attached Images
File Type: jpg 40 early firewall .jpg (17.4 KB, 73 views)
File Type: jpg 40 early firewall with tag above hand throttle bump.jpg (49.9 KB, 71 views)

Last edited by Terry,OH; 04-20-2021 at 11:36 AM.
Terry,OH is offline   Reply With Quote
Old 04-18-2021, 08:05 AM   #13
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by woodiedude View Post
I recently acquired a 40 Convertible and I saw this post. I am new to the group but I will try to attach a picture of my engine that has a body tag mounted with four nails. The tag has been painted over and I didn’t try to remove any of the paint. I can get more pictures if needed next week.
That's the patent tag.
I've attached a photo of a body tag - this one on the last '40 convertible I'd restored.
Attached Images
File Type: jpg conv. body tag.jpg (39.6 KB, 132 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-18-2021, 11:43 AM   #14
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
I'd like to hear from guys with '40 Ford convertibles...
Is there or, to your knowledge, was there, a body tag on your vehicle? Or, are there numbers stamped in to the firewall?
I have posted two photos below that allow a glimpse of where a tag should have been and a glimpse as to where numbers may have been stamped.
Please, if you are able to respond, allow as much as you know in regard to your vehicles 'pedigree".

The tag was "nailed" to the upper- left corner of the firewall. Stamping was below the voltage regulator.

thanks!!!

The tag riveted to upper edge of firewall in second photo doesn't look like a body number tag and body number. I have no such tag or any body tag on my 40 conv. For what it is worth my 40 wagon firewall has the body number stamped into firewall under lower edge of voltage regulator.
40larry
40larry is offline   Reply With Quote
Old 04-18-2021, 12:22 PM   #15
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
The tag riveted to upper edge of firewall in second photo doesn't look like a body number tag and body number. I have no such tag or any body tag on my 40 conv. For what it is worth my 40 wagon firewall has the body number stamped into firewall under lower edge of voltage regulator.
40larry
Larry, Which post are you referring to ("second photo")?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-20-2021, 12:08 PM   #16
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
Larry, Which post are you referring to ("second photo")?

Sorry. I should have said left side photo with tag on upper right of firewall.
40larry is offline   Reply With Quote
Old 04-20-2021, 01:24 PM   #17
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
Sorry. I should have said left side photo with tag on upper right of firewall.
Which post number?
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-20-2021, 01:40 PM   #18
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
Which post number?

Post No. 1 Your opening post. I think that our problem is which side is left and right. On your opening photo on left side of your posting there is a tag attached with drive nails on the upper part of firewall. The tag is on upper left side of the firewall and upper right side in the photo. What is on that tag?
40larry is offline   Reply With Quote
Old 04-20-2021, 02:14 PM   #19
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
Post No. 1 Your opening post. I think that our problem is which side is left and right. On your opening photo on left side of your posting there is a tag attached with drive nails on the upper part of firewall. The tag is on upper left side of the firewall and upper right side in the photo. What is on that tag?

Kube....In ref to Larry's question, I'm assuming this is your blue coupe in your avatar. Didn't you once note that this number was the SERIAL for this "special-order", lawman's coupe? I believe it started with a "P". Or am I full of it once again? DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 04-20-2021, 02:23 PM   #20
40fconvt
Junior Member
 
Join Date: Jun 2010
Location: Denver Co.
Posts: 14
Default Re: 1940 Ford convertible body tags

My 40 convert purchased well used in 1955 with pull out ashtrays has three small holes but no tag.one hole would have hidden under the tag.
40fconvt is offline   Reply With Quote
Old 04-20-2021, 02:30 PM   #21
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
Post No. 1 Your opening post. I think that our problem is which side is left and right. On your opening photo on left side of your posting there is a tag attached with drive nails on the upper part of firewall. The tag is on upper left side of the firewall and upper right side in the photo. What is on that tag?
Hey Larry, Just attempting to be certain you and I are talking about the same thing.
That tag, as V8Coopman recalled correctly, is the serial number of that car.
I have never been able to glean any information about that tag / serial number.
This car is extremely well documented as being special ordered for a sheriff.
There have been a few theories put forth as to what that number may signify but again, never any documentation via the BFRC.

Post #13 clearly depicts a proper '40 convertible body tag.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-20-2021, 06:09 PM   #22
cobramike
Member
 
Join Date: Nov 2015
Posts: 31
Default Re: 1940 Ford convertible body tags

Mine has stamped number under hot air heater knockout. Number as best I can read is 18 b 234ch. Can't attach phot here, but will send to your personal email
cobramike is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-20-2021, 07:54 PM   #23
G32
Senior Member
 
Join Date: May 2010
Posts: 258
Default Re: 1940 Ford convertible body tags

Mike;

My 40 Cnvt has unsteady stamping under center heater hole -Hot air knockout :



1AR24CH

Gene Tulsa

Last edited by G32; 04-20-2021 at 08:01 PM. Reason: clairity
G32 is offline   Reply With Quote
Old 04-21-2021, 11:56 AM   #24
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
Hey Larry, Just attempting to be certain you and I are talking about the same thing.
That tag, as V8Coopman recalled correctly, is the serial number of that car.
I have never been able to glean any information about that tag / serial number.
This car is extremely well documented as being special ordered for a sheriff.
There have been a few theories put forth as to what that number may signify but again, never any documentation via the BFRC.

Post #13 clearly depicts a proper '40 convertible body tag.
0


You are saying that the number on the tag is the VIN number for that vehicle? The number on the tag is same as stamped into the frame up front starting with 18- for car with 221cubic inch engine or 99- for a car built with the 239 cubic inch Mercury or truck engine? Never saw that before.......40larry
40larry is offline   Reply With Quote
Old 04-21-2021, 12:10 PM   #25
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
0


You are saying that the number on the tag is the VIN number for that vehicle? The number on the tag is same as stamped into the frame up front starting with 18- for car with 221cubic inch engine or 99- for a car built with the 239 cubic inch Mercury or truck engine? Never saw that before.......40larry
Yes sir. The three along the frame as well as the title all match.
I'd never seen this before or since either. Nor, to reiterate, could I find a thing that would help figure out why this happened. ONLY a theory, but in 1940, these cars (with Mercury engines) were not a "mainstay" offering and the "program" to build such cars was in it's first year.
There were anomalies for certain in the numbering system of these special vehicles. Communication issues between assembly plants??? No defined method of numbering???

This particular coupe had been in the same family since new. It was passed to the son when the man that had ordered it passed in about 1972ish.
The documents that were saved was a treasure trove for weird guys like - I love this kind of stuff.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-21-2021, 02:17 PM   #26
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Kube View Post
Yes sir. The three along the frame as well as the title all match.
I'd never seen this before or since either. Nor, to reiterate, could I find a thing that would help figure out why this happened. ONLY a theory, but in 1940, these cars (with Mercury engines) were not a "mainstay" offering and the "program" to build such cars was in it's first year.
There were anomalies for certain in the numbering system of these special vehicles. Communication issues between assembly plants??? No defined method of numbering???

This particular coupe had been in the same family since new. It was passed to the son when the man that had ordered it passed in about 1972ish.
The documents that were saved was a treasure trove for weird guys like - I love this kind of stuff.

My attempt to read the numbers off the tag in the photo comes up with 1-62028270 which doesn't correspond to any VIN number for these cars. If I read it wrong what does it actually say?
40larry is offline   Reply With Quote
Old 04-21-2021, 03:35 PM   #27
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
my attempt to read the numbers off the tag in the photo comes up with 1-62028270 which doesn't correspond to any vin number for these cars. If i read it wrong what does it actually say?
pc 2628270
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-21-2021, 07:45 PM   #28
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
pc 2628270

Those numbers are not in the sequence of VIN numbers used in 1940 for either engine choice and they are on your frame?
40larry is offline   Reply With Quote
Old 04-21-2021, 07:56 PM   #29
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
Those numbers are not in the sequence of VIN numbers used in 1940 for either engine choice and they are on your frame?
Yes sir, in all three places. The same number is also on the Western Union Telegram that notified the dealer that the car was built and ready to be picked up at the Rotunda.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-22-2021, 11:50 AM   #30
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
Yes sir, in all three places. The same number is also on the Western Union Telegram that notified the dealer that the car was built and ready to be picked up at the Rotunda.



Wow. That is amazing. This could create a problem if this car is ever registered for sale in an auction such as Barrett Jackson. They have experts inspect all the cars for proper VIN identification and numbering. Ask me how I know this........40larry
40larry is offline   Reply With Quote
Old 04-22-2021, 11:54 AM   #31
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
Wow. That is amazing. This could create a problem if this car is ever registered for sale in an auction such as Barrett Jackson. They have experts inspect all the cars for proper VIN identification and numbering. Ask me how I know this........40larry
In my opinion there should be no issue. Having the title match the frame and all of the supporting documents I'd think should actually add to intrigue (read: value).
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 04-22-2021, 01:05 PM   #32
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: 1940 Ford convertible body tags

And, the fact that it is an "oddball", would probably push the "intrigue" even higher.
tubman is offline   Reply With Quote
Old 05-06-2021, 01:52 PM   #33
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

A friend of mine sent this photo of a very "original" '40 convertible with a body number tag.
I believe we can at minimum agree that there was no 100% "rule" of what bodies were numbered in 1940 and how.
Attached Images
File Type: jpg tag.jpg (45.3 KB, 79 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-06-2021, 11:49 PM   #34
bmwboxerboy
Member
 
Join Date: Aug 2015
Location: San Jose, CA
Posts: 46
Default Re: 1940 Ford convertible body tags

For my 1939 Convertible Coupe, I would appreciate any leads for a body tag starting with 91A-76A-xxxxx

The picture provided here was from a Mercury, also drivers side above the voltage regulator.

Mark
IMG_5661.jpg


Sent from my iPhone using Tapatalk
bmwboxerboy is offline   Reply With Quote
Old 05-07-2021, 08:19 AM   #35
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,926
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by bmwboxerboy View Post
For my 1939 Convertible Coupe, I would appreciate any leads for a body tag starting with 91A-76A-xxxxx

The picture provided here was from a Mercury, also drivers side above the voltage regulator.

Mark
Attachment 462855


Sent from my iPhone using Tapatalk
That would be my Mercury in the above post/photo & I also believe our 40 Mercury Convertible Sedan has a body tag as well. I will look and post a picture IF wanted??
rockfla is offline   Reply With Quote
Old 05-07-2021, 01:42 PM   #36
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
A friend of mine sent this photo of a very "original" '40 convertible with a body number tag.
I believe we can at minimum agree that there was no 100% "rule" of what bodies were numbered in 1940 and how.

This tag gives an expected body number for the 1940 Ford convertible. It is held on with slotted head screws instead of drive nails and is mounted haphazardly on an angle. My 40 conv has no sign of holes for a tag in this area...........40larry
40larry is offline   Reply With Quote
Old 05-07-2021, 01:53 PM   #37
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by 40larry View Post
This tag gives an expected body number for the 1940 Ford convertible. It is held on with slotted head screws instead of drive nails and is mounted haphazardly on an angle. My 40 conv has no sign of holes for a tag in this area...........40larry
I did note the screws which I find difficult to believe are authentic. However, there's no real way to know whether or not they are.
Does your car have indentations in the sheet metal in that area?
Every car I've seen has those, unless they have been filled.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-08-2021, 01:36 PM   #38
40larry
Senior Member
 
Join Date: May 2010
Location: Northridge, CA
Posts: 234
Default Re: 1940 Ford convertible body tags

Quote:
Originally Posted by Kube View Post
I did note the screws which I find difficult to believe are authentic. However, there's no real way to know whether or not they are.
Does your car have indentations in the sheet metal in that area?
Every car I've seen has those, unless they have been filled.

My car is untouched original and has no signs of tag. No indentations or holes. If you want to see photo please PM me with a number to text to..
40larry is offline   Reply With Quote
Old 05-08-2021, 07:15 PM   #39
Ken/Alabama
Senior Member
 
Ken/Alabama's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 3,237
Default Re: 1940 Ford convertible body tags

Finally found the body tag that came with my 40 Convertible.
Attached Images
File Type: jpg 116F610A-220A-433C-ADE5-151589FA2ED9.jpg (34.0 KB, 29 views)
Ken/Alabama is offline   Reply With Quote
Old 05-08-2021, 07:55 PM   #40
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 4,725
Default Re: 1940 Ford convertible body tags

Typically with the older body number plates like 1936 the tag starts with the model identification followed by the body type number and then the number in sequence built in the model year by the body manufacturer. Such as 01A for 1940, 66 for the Deluxe Convertible Club Coupe then as above in post #39, 1975 for the 1975 body made by the Mfg in 1940. There were a couple of different Mfg for the body one Mfg used the flat body plate another used the body plate with the embossed edge such as post#34 above. Only bodies mfg. by outside manufacturer for Ford had the body plate. Bodies made by Ford did not have the body plate. Typically open car bodies were made outside Ford. This is an explanation of the numbering and style of the body plates for the earlier Fords. It appears several of the body plates posted above for 1940 are in line with the 1936 body tags. It is possible Both Ford as well as their contracted body Manufactures made open car bodies, that may explain why some Convertible bodies do not have the plate???
Terry,OH is offline   Reply With Quote
Old 05-10-2021, 07:56 AM   #41
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: 1940 Ford convertible body tags

Terry<OH has kindly shared a photo of a tag found on a convertible.

It is more than apparent that Ford tagged "some" wagons and "some" convertibles. There appears to have been variations in the style / format of those tags. Still to be determined is when were these tags utilized and why on some vehicles and not others.

In post #40, Terry makes a very valid point in regard to outside suppliers of bodies. However, at least from my research, (only) Ford was making the bodies by 1940.
Attached Images
File Type: jpg body tag 40 ford convertable.jpg (3.5 KB, 50 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 05-10-2021, 10:58 AM   #42
fcompoccio
Member
 
Join Date: Feb 2017
Posts: 37
Default Re: 1940 Ford convertible body tags

Sorry Kube no tags on my Convert. When I bought had an after market firewall is there anyplace else the number may be stamped?
fcompoccio is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-10-2021, 01:57 PM   #43
fcompoccio
Member
 
Join Date: Feb 2017
Posts: 37
Default Re: 1940 Ford convertible body tags

Hi Yours looks in much better shape than the one I bought. Mine has been a 2 year nightmare and still going. please keep in touch and let me know your progress. I would be happy to send you any pics of my progress but mine is a restomod with a brand new Chevy drive train. Ive had no reference where anything goes because mine has a new floor and firewall with no holes so Ive had to do my own figuring with some help from guys on here especially Kube.
Frank
fcompoccio is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:25 PM.