|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-08-2013, 02:32 PM | #1 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Question about windshield hinge
Getting ready to put my windshield in, but it seems something is not right.
The hinge has two places where the metal is bent up( on purpose) for reasons I can't figure out. If I mount it like it is then the screws around this area will pull the rest of the hinge in a bind and the entire hinge surface will not be flat and twist. _____/---\_____________/---\______ Kinda looks like this I'm i missing something? |
12-08-2013, 03:42 PM | #2 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,162
|
Re: Question about windshield hinge
What kind of car and year are you working on?
Rusty Nelson |
Sponsored Links (Register now to hide all advertisements) |
|
12-08-2013, 04:32 PM | #3 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
31 coupe,
It would seem to me that the hinge would fit better if it was flat from one side to the other. |
12-08-2013, 04:55 PM | #4 |
Senior Member
Join Date: Jun 2011
Location: Oakton, VA
Posts: 437
|
Re: Question about windshield hinge
I just hung a front window into a 1931 coupe. The hinge was flat. Your common sense is correct. The real problem is the windshield frame gasket. It's slightly thicker than what you removed and makes fitting the window at the bottom a problem. A better solution might be a butyl compound: never silicon.
|
12-08-2013, 07:58 PM | #5 | |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: Question about windshield hinge
Quote:
I agree about the flat hinge but sure would like to see Ralph's hinge in question!
__________________
http://www.abarnyard.com/ |
|
12-09-2013, 09:16 AM | #6 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
Sponsored Links (Register now to hide all advertisements)
I have not bought my seals yet, any recommendations? |
12-09-2013, 10:50 AM | #7 |
Senior Member
Join Date: May 2010
Location: South East NJ
Posts: 3,398
|
Re: Question about windshield hinge
I had a guy that could not get the windshield to close.
Turns out the header wood did not fit the cover pan so the pan did not fit flat to the wood. Something to check at this stage. |
12-09-2013, 12:42 PM | #8 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
I had the same problem, I had to trim the ends of the metal header cover so that it would go back far enough for the screw holes to line up and the windshield screws to not be hitting thin air.
|
12-15-2013, 12:53 PM | #9 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
lets see if this works, here is a picture of my hinge, I
think I may have to flatten this to make it work. |
12-15-2013, 01:28 PM | #10 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
looks factory to me, like it was bent in a press, and they are evenly spaced, and the width of the hinge fits properly. Seems to me it would be shorter in length if someone did this to the original one.
|
12-15-2013, 01:52 PM | #11 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 1,593
|
Re: Question about windshield hinge
Also never saw one like it. Hard to see but the frame looks like it doesn't have a draft deflector. Therefore, the windshield assembly isn't original.
|
12-15-2013, 02:10 PM | #12 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
By "draft deflector" do you mean the large flange at the bottom that covers the slots in the dash rail when the windshield is closed?
|
12-15-2013, 02:35 PM | #13 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
Here's another strange thing, when I put the garnish moldings in and mock up the windshield the brackets for the swing out arms hit the garnish and don't allow it to close all the way.
|
12-15-2013, 02:45 PM | #14 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
Looks like I have a 28-29 frame, if I change the brackets for the swing out arm, will it still work?
|
12-15-2013, 03:46 PM | #15 |
Junior Member
Join Date: May 2010
Location: Manitoba, Canada
Posts: 11
|
Re: Question about windshield hinge
Deflector flange across bottom has to be trimmed to clear windshield posts, as per Marco's pictures. Also slider arm brackets have to be changed to 30-31 that extend closer to center of car. Those brackets can't be extended with spacers, ask me how I know.
Canuck64
__________________
30 Ford Coupe Build “ http://chevelle406.wordpress.com/ ” UPDATED JANUARY 7, 2014 |
12-15-2013, 04:20 PM | #16 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
Thanks Canuck, I have already trimmed the flange as I have a 36 dash mounted in my car. I'll see if I can come up with a pair of those brackets. And I guess I will have to flatten the hinge as well.
|
12-15-2013, 05:42 PM | #17 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
That's the ticket, and I don't have to look for another windshield,
Thanks Ralph |
12-15-2013, 07:47 PM | #18 |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: Question about windshield hinge
I believe that upper hinge will present numerous other issues as well. Look closely at cross section shape of Coupe's pic I reposted here.
__________________
http://www.abarnyard.com/ |
12-16-2013, 09:58 AM | #19 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
other than the taper at the end, I don't see the difference.
|
12-16-2013, 02:56 PM | #20 |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: Question about windshield hinge
Ok, now I can see better. It's been a LONG time since I helped with a '29 windshield install and was thinking the hinge was different. Your first pics had me confused as I didn't realize it was still attached to the top of the frame. Sliding the hinge apart is one of the first things most folks do.
__________________
http://www.abarnyard.com/ |
12-19-2013, 04:09 PM | #21 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: Question about windshield hinge
Well I spoke to a buddy of mine and lo and behold he had an extra 30-31 windshield frame. It's missing the wind deflector, but otherwise in good shape.
The only issue is the hinge is frozen, if I can free it up this will work great |
03-10-2014, 07:16 PM | #22 |
Junior Member
Join Date: Dec 2011
Posts: 5
|
Re: Question about windshield hinge
Hey guys, I'm facing the same question as Ralph. I have the exact same hinge and the stampings are factory. I have found three or four different style hinges just in my collection of model A windshield frames. Some have square cut outs, some have none, one has the stampings like the one in Ralph's pic and there are at least three different spacing arrangements on the screw holes. I can make any of them work but it would be nice to know which is correct for what model. If anyone has figured this out I'd like to compare notes.
|
Sponsored Links (Register now to hide all advertisements) |
|
12-03-2014, 04:34 PM | #23 |
Junior Member
Join Date: Apr 2014
Posts: 7
|
Re: Question about windshield hinge
Repro windshield hinge gasket comes solid. Anybody got inkling if should be notched fr installation or holed fr screws? Notched look as if would make install easier. Holes would immobilize. Kinda torn my own self and of crse tossed the old one. AFF
|
12-04-2014, 10:17 AM | #24 |
Member
Join Date: Nov 2012
Location: North Branch, MN
Posts: 42
|
Re: Question about windshield hinge
I believe its a briggs fordor hinge from my research. I used the same windsheild frame and hinge on my late 30 ccpu. I cut the two raised sections out and welded in peices to make it flat. I also changed the swing arm brackets on the frame to the 30-31 style worked well on my truck
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|