|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-05-2020, 04:49 PM | #1 |
Senior Member
Join Date: Nov 2011
Location: Readfield, Maine
Posts: 347
|
Remanufactured Flathead
I found a 59 block that has a re manufactured tag on the one piece bell housing on drivers side. It was done in Boston Ma and has a code # stamped on it. There is an A stamped on each head. There is no 59 anywhere on the block. It has a 2 piece oil pan. I was told it came out of a 47` truck. What might I expect concerning what they did for specs during the rebuild process back in the 40`s. re-sleeve, bore size, etc, etc?
|
09-05-2020, 05:43 PM | #2 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,178
|
Re: Remanufactured Flathead
I thought those tags also gave those specs. I've seen those tags that say for ex. .010" over, etc.
If cheap enough, sounds like a winner. Two piece pan is great addition to any 59AB. |
Sponsored Links (Register now to hide all advertisements) |
|
09-05-2020, 06:11 PM | #3 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Remanufactured Flathead
On occasion, the specs it was built to are stamped in to the surface plane that the intake bolts to. Usually right - front.
I've seen plenty of those tags that were not stamped. "A" CAST on heads are '40. Why do you believe it's a '47 "59" series block? Ford remanufactured engines were done very well. Still, how has it been stored? How was it used? It may be junk today... I would strongly suggest you remove at the very minimum, the intake to inspect. I'd also prefer to remove the pan.
__________________
"I can explain it for you. However, I can't understand it for you". |
09-05-2020, 06:44 PM | #4 |
Senior Member
Join Date: Nov 2011
Location: Readfield, Maine
Posts: 347
|
Re: Remanufactured Flathead
The previous owner of the engine saw it come out of a 47`truck. Its been under cover for several years and the oil still in the pan was clean. The intake was taken off the day before i picked it up as i did not want it. I will check further for the stamping s and remove the pan which is is in very good shape. There was a number cast into the bell housing with a star symbol on either side of the number. The number was higher up on the bell housing from where the 59 would be stamped. I plan on using my 59a heads in any case. I just had them re planed. Thanks
|
09-05-2020, 06:54 PM | #5 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: Remanufactured Flathead
If it was a Ford re-manufacture, it would have been done at the Somerville plant before it closed in 1958. I have had several of them and I believe one was sleeved. They seemed to be pretty well done rebuild. Photo of the plant as it looked before they closed it. That area a commercial area called assembly square.
Last edited by russcc; 02-22-2021 at 01:17 PM. |
09-05-2020, 07:35 PM | #6 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,178
|
Re: Remanufactured Flathead
Sponsored Links (Register now to hide all advertisements)
|
09-05-2020, 07:40 PM | #7 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,571
|
Re: Remanufactured Flathead
clean oil in the pan is because the dirt settles down to the bottom after a decade or two
|
09-05-2020, 07:44 PM | #8 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,963
|
Re: Remanufactured Flathead
no 59 on bell housing, A heads which would have needed to have some milling work to work on a 59 eng--I would suggest that it is a 39 to 41 engine put in a 47 truck
|
09-05-2020, 07:46 PM | #9 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Remanufactured Flathead
According to the Ford Engine Parts Reconditioning manual Ford had authorized rebuild facilities all over the place. Not sure how one is ID over another. This is the tag they show being used, but not sure if a location is on it. The manual is not dated, but the way it is written it sounds like it is from the war years.
Last edited by JSeery; 09-05-2020 at 07:53 PM. |
09-05-2020, 07:48 PM | #10 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Remanufactured Flathead
The tags on the engines I've had had the plant that did them near the top.
__________________
"I can explain it for you. However, I can't understand it for you". |
09-05-2020, 07:49 PM | #11 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Remanufactured Flathead
That's my thinking...
__________________
"I can explain it for you. However, I can't understand it for you". |
09-05-2020, 07:51 PM | #12 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,995
|
Re: Remanufactured Flathead
Quote:
So clean oil in this aforementioned engine means little if anything.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
09-05-2020, 08:30 PM | #13 |
Senior Member
Join Date: Feb 2017
Location: Rochester Wa
Posts: 574
|
Re: Remanufactured Flathead
Interesting. The '32 "rebuilt" engine we have has this riveted to it.
|
09-05-2020, 08:35 PM | #14 |
Senior Member
Join Date: Feb 2017
Location: Rochester Wa
Posts: 574
|
Re: Remanufactured Flathead
Try again withn attachments. Messed it up.
|
09-05-2020, 08:37 PM | #15 |
Senior Member
Join Date: Feb 2017
Location: Rochester Wa
Posts: 574
|
Re: Remanufactured Flathead
Must be doing something wrong
|
09-05-2020, 08:54 PM | #16 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Remanufactured Flathead
That's similar to the one on the last block I got, 59a.
|
09-06-2020, 05:21 AM | #17 |
Senior Member
Join Date: Nov 2011
Location: Readfield, Maine
Posts: 347
|
Re: Remanufactured Flathead
I will try and send some photos of the engine.
|
09-06-2020, 05:50 AM | #18 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,178
|
Re: Remanufactured Flathead
|
09-06-2020, 06:04 AM | #19 |
Senior Member
Join Date: Sep 2013
Location: Dighton, Mass
Posts: 1,230
|
Re: Remanufactured Flathead
All I can add, is 80% of reman' s around here were done by Cody Ford authorized. As
far as the riveted plate most just had a serial or job number. But some only had ".010" and thats a guess, rods or mains or both?? I think Cody was somewhere on Rt 9 Somerville, Revere area, don't know. Back in the bus co.we bought several from our local Ford dealer, I think the dealer was the only way to get one. While on this subject, got to thinking of that HUGE blue Ford ovel all made from blue and white panzies at the Sommerville plant. Just maybe Sommerville Historical would have a picture of that. It was on a hill and kind of like 'Hollywood" sign up on hill in Calf. |
09-06-2020, 07:55 AM | #20 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,859
|
Re: Remanufactured Flathead
It's probably a 221 bored .030/040, with ,010/020 bearings. I was in the Patterson NJ plant back in the 60's to pick up a JD 172 industrial engine. I watched them do some in line 6 cyl engines. I asked if they had any flatheads. He said they were all sold off years ago, thay made allot for Sears and other stors. Yhey only rebuild engines one way depending on sales and only blocks that met certian requirements. Most were .030 over and ,010 on the crank. However, if they were short of cores they would take a .040/.020. Setting up the machinery to do an engine took awhine as they did most all kinds. One sad news, they didn't do Merc 4" cranks, they were scrapped. Often wondered how they checked the blocks??
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|