10-26-2018, 11:10 AM | #1 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Weard leaks
My rebuilt engine hasn't run yet. A month ago I filles the cooling system using distilled water and some Bardahl protector. Today I find 'something' is leaking from the head gasket, all around the engine. The stuff dripping down is brown and sticky. Is Bardahl eating my copper head gasket ? Any ideas ?
|
10-26-2018, 12:42 PM | #2 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Weard leaks
Sometimes coolant seeps through the filler material in the gasket to the outside of the block. It most likely is not a problem but is unsightly. An old-timer fix is to seal the edges of the gasket water passage edges before assembly. After you get it running and do a few re-torques on the head nuts it probably will not continue.
|
Sponsored Links (Register now to hide all advertisements) |
|
10-26-2018, 01:31 PM | #3 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
Thx J.Franklin, my head gasket is from Mac's, some 30 years ago. My guess would be the gasket filler material doesn't handle the modern additive to the cooling water. The additive created lots of small channels to the outside of the block. Once they were there, clear coolant is coming out. So my guess would be the residues I found earlier (brown and sticky) are filler material resolved by the cooling water additive I used. If so, we should put a warning out not to use any unsafe additives ???
|
10-26-2018, 01:34 PM | #4 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Weard leaks
Perhaps using a modern copper gasket is advisable?
|
10-26-2018, 03:37 PM | #5 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Weard leaks
I wouldn't change a thing unless you have to after running the car for a while and doing the re-torques.
|
10-26-2018, 05:52 PM | #6 |
Senior Member
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,776
|
Re: Weard leaks
Sponsored Links (Register now to hide all advertisements)
|
10-26-2018, 07:56 PM | #7 |
Senior Member
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,909
|
Re: Weard leaks
While I'm not familiar with Bardahl I looked it up on line and found two products on their website that were for cooling systems. One was an anti rust (rust remover) and water pump lubricant. The directions for it were to add it to the coolant, run it for 15 minutes, let the system cool, drain the solution and then refill with a standard type coolant mixture.
The other was a stop leak product that is to be added to a coolant mixture. If one of these is what you used with just distilled water I'm thinking you may have inadvertently allowed considerable rust to form in the block. Have you drained some water to see what it looks like? Seems to me that putting water into an engine and letting it rest for an extended period without running it through several heat / cool cycles and re-torquing until the head gasket settles in opens the door for the gasket to leak. Putting a 50/50 coolant solution into an engine is one of the last things I do just before start up. I see no reason to put in a stop leak product into a new rebuild to fix a problem that probably is not there.
__________________
Dave / Lincoln Nebraska |
10-27-2018, 12:57 AM | #8 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Weard leaks
I agree with 1crosscut drain the solution from the block until you are ready to run your car. You can store it in a jug. I use a powered stop leak product to stop gasket weep.
|
10-27-2018, 07:05 AM | #9 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
1crosscut,
You are right. not intended for permanent usage. Too bad there were no instructions on how to apply. Dutch description make it look like you can leave this stuff in. This stuff seems to be very agressive. I drained the sysstem and will have to put a new headgasket in. |
10-27-2018, 09:11 AM | #10 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Weard leaks
Did you check the cylinders?
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
10-27-2018, 09:58 AM | #11 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
Katy, not yet, will do. I am hoping the shape if the copper head gasket is such that the gasket filler is not in touch with the cylinder space.
|
10-27-2018, 10:04 AM | #12 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Weard leaks
Quote:
If leaving it for a while after draining, perhaps thoroughly flush/backflush with water, or water/dawn, or white vinegar to insure nothing gets left in the motor? |
|
10-27-2018, 11:47 AM | #13 |
Senior Member
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,909
|
Re: Weard leaks
I like the idea of flushing the engine / radiator prior to removing the head.
__________________
Dave / Lincoln Nebraska |
10-27-2018, 12:42 PM | #14 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Weard leaks
Do you really want/need to remove the head? It just seems to be a premature operation before running and a couple of re-torques. The filler material does not reach the cylinder bores or valve area, just the water jacket holes.
|
10-27-2018, 12:54 PM | #15 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
Will flush tomorrow ! Good idea thx
|
10-27-2018, 12:59 PM | #16 |
Senior Member
Join Date: May 2010
Location: Innisfil, Ontario Canada
Posts: 1,174
|
Re: Weard leaks
I had the same thing with my engine. After I run it 5 times and re-torqued the head 5 times as the builder told me to do. The sealant stopped coming out between the head and the block. Wait until you do this. Save yourself some grief.
|
10-27-2018, 01:32 PM | #17 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: Weard leaks
All gaskets that are layered or thick composition will settle (sink to being thinner) with heat and cooling cycles. That's why the re-torque is important.
|
10-27-2018, 04:03 PM | #18 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
J.franklin, thats what i need ! I will flush and then change the gasket, what the heck ! I do'nt want to live with the idea my gaseket in not ok!
|
10-27-2018, 04:19 PM | #19 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Weard leaks
Am not sure what the Bardall would do if it got in the radiator, especially if left in for a long time, not familiar with it. Possibly either coat the tubes, or plug it up - causing running hot or boiling over?
|
10-27-2018, 11:58 PM | #20 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Weard leaks
Why do you think the gasket is bad? I am saying do not remove the head until you have a running engine and know you need to change the gasket. At least 2-3 heat/cool/re-torque cycles.
|
10-28-2018, 08:21 AM | #21 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
J.Franklin, maybe you are right. I filled her up with clear water and there are only two small leaks left, front right. So i will follow your advice and retorque the head first.
|
10-28-2018, 09:13 AM | #22 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Weard leaks
If after the retorque and still uncomfortable or still leaking, perhaps contact Bardalls or a distributor of Bardalls and ask their opinions. ask if it should be flushed out, if yes ask about proper flushing. If using white vinegar or something caustic a final flush of distilled water/baking soda to neutralize .
And/or contact a Model A restoration shop or motor rebuilder withsame questions. |
Sponsored Links (Register now to hide all advertisements) |
|
10-28-2018, 09:39 AM | #23 |
Senior Member
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,554
|
Re: Weard leaks
After re-torquing the head, start the engine and go through at least warming it up and see if the radiator is plugged. I would be more concerned with that than degradation of the copper head-gasket. The Bardahl may now be a lump in the system somewhere. What was the thinking in putting the engine together and then not finishing by running and torquing a few time? That is a procedure I have not been informed of yet. May have merit, but I fail to see any logic there. Perhaps we can all learn.
|
10-28-2018, 10:32 AM | #24 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Weard leaks
Quote:
#9 hazelhoff Senior Member Join Date: Dec 2013 Location: The Netherlands Posts: 205 Re: Weard leaks 1crosscut, You are right. not intended for permanent usage. Too bad there were no instructions on how to apply. Dutch description make it look like you can leave this stuff in. This stuff seems to be very agressive. I drained the sysstem and will have to put a new headgasket in. ---------------------------------- He seems to think the Bardalls is active/aggresive, and is concerned about it slowly causing damage that will show up in the future. One of the reasons I suggested calling a distributor or Bardalls. |
|
10-28-2018, 11:22 AM | #25 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: Weard leaks
As others have said; Heat is an essential part of the head gasket job. Heat and cooling cycles. Not just warm, Hot, then re -torque after cooling. After this process, then you can judge the job technique and materials.
|
11-01-2018, 11:46 AM | #26 |
Senior Member
Join Date: Dec 2016
Location: Sunrise Beach, Mo
Posts: 439
|
Re: Weard leaks
Sponsored Links (Register now to hide all advertisements)
|
11-01-2018, 12:57 PM | #27 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
Once more an update, the gasket is leaking all over the place again when filling up. Today I removed the head. Water all over the place ! Even one cylinder was attacked !
The Dutch product description basically says you should leave the Bardahl in. The American product instructions say you have to drain it after running for 15 minutes. Believe me, Bardahl eats your head gasket ! Spefically the asbestos. It is dangerous to your system ! |
12-15-2019, 09:52 AM | #28 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
So, you guys think it is OK for the head gasket to leak some drops of water after installation ? Will it end after a few runs/retorques ?
Do you want to apply some locktite sealant extra to the standard copper gasket around the water holes ? |
12-15-2019, 11:54 AM | #29 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Weard leaks
I have found that when using a copper gasket, if you use a liberal application of Permatex Copper Spray, you will not have any weeping of coolant, either from studs or from the edge of the gasket. This does not mean you can skip the required re-torque sequence. The mess you get glueing the gasket to head and block surfaces when using composite gaskets is a non-issue with copper gaskets.
|
12-15-2019, 12:12 PM | #30 |
Senior Member
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,909
|
Re: Weard leaks
I don't think that it should leak after installation of new head gasket.
Everyone seems to have a different way of going about installing a new head gasket. If you are putting in new studs check each one to see if it goes into the water jacket. I put a bit of Indian Head shellac on the threads going into the block on each stud. I use two light coats of copper coat spray on the copper head gaskets allowing the solvents to flash off between coats. Install the head while the gasket is still a bit tacky.
__________________
Dave / Lincoln Nebraska |
12-15-2019, 03:48 PM | #31 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Weard leaks
Have you milled the cylinder head? Most used heads I have found are not flat and need to be milled. This could cause your leaks.
|
12-16-2019, 06:43 AM | #32 |
Senior Member
Join Date: Dec 2013
Location: The Netherlands
Posts: 387
|
Re: Weard leaks
Yes, the block and the head were milled !
|
12-16-2019, 08:08 AM | #33 |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Weard leaks
If it is only seeping through the filler material in the gasket you can put in some stop leak like others have said. If the gasket isn't hemmed on either end there's always a chance coolant will seep through.
|
12-16-2019, 04:19 PM | #34 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: Weard leaks
Mine Gott. Why did you put in this additive in the first place - Leaking? now leaking still so it is the additive. I am sure no stop leak that has been around for 50 - 70 years eats head gaskets. When you pulled the head, why did you not drain the coolant first. Did you study the old gasket for signs of damage or failure. What were the results? The old gasket might indicate problems in the surfaces that still exist. Non hardening sealers are OK around the studs threads and the gasket holes but not locktite.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|