|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-21-2021, 02:35 PM | #41 | |
Senior Member
Join Date: May 2010
Posts: 2,791
|
Re: 3rd engine failure...getting frustrated
Quote:
What did the catalogues advertise them at back in the early 60's, 75 bucks exchange? |
|
07-21-2021, 03:19 PM | #42 | |
Senior Member
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,824
|
Re: 3rd engine failure...getting frustrated
Quote:
Enjoy. |
|
Sponsored Links (Register now to hide all advertisements) |
|
07-21-2021, 03:24 PM | #43 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,528
|
Re: 3rd engine failure...getting frustrated
Quote:
Engines rebuilt during that time used inferior pistons in comparison by today's standards. Stainless valves were rarely used, one-piece guides were not an item yet (-most used Argentina-manufactured two-piece guides), good camshafts were almost non-existent and nothing then compared with a Stipe cam of today. Then, often times cast bearing material had Lead in it, and/or it was old material re-smelted and re-used which causes reliability issues. Machine shop technology and the machinery used has improved vastly in the past 50 years too? The reason many people only drive their Model-A around 40mph is because they have a 1960's rebuilds!! Think about what Jeff is saying. A $75 engine back then adjusted to 2021 prices would be how much? |
|
07-21-2021, 03:30 PM | #44 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,528
|
Re: 3rd engine failure...getting frustrated
Quote:
|
|
07-21-2021, 04:23 PM | #45 |
Senior Member
Join Date: May 2010
Location: Campbell,CA, USA
Posts: 321
|
Re: 3rd engine failure...getting frustrated
Brent,
In post 37, rotorwrench posted the answer. Original cylinders were rolled to 3.875/3.876 inch diameter. Things have changed over 90 years. The new engine has the cylinders plateau honed to 3.875/3.876 inch diameter. Click on the picture to enlarge. |
07-21-2021, 06:02 PM | #46 |
Senior Member
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,059
|
Re: 3rd engine failure...getting frustrated
Sponsored Links (Register now to hide all advertisements)
The quality of aftermarket Model A parts have been questionable over the years. Why? maybe it has to do with the fact that trying to keep costs down has forced the quality to suffer. Maybe it has to do with the fact that the market is small for Model A's and as a result parts are not necessarily made by craftsmen. Now, on the other hand, Terry Burtz has been able to produce new parts, in China, but from a manufacturer who supplies engines for major car brands. There is a very big difference between a casting house that makes blocks and cranks vs iron skillets. Just an observation, I have had junk parts from questionable sources and original Ford parts butchered by someone in the past. My money says the import engine is good. John
__________________
As Carroll Smith wrote; All Failures are Human in Origin. |
07-21-2021, 06:04 PM | #47 | |
Senior Member
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,824
|
Re: 3rd engine failure...getting frustrated
Quote:
The people who were rebuilding those engines were also like a mechanic today working on a 1990 car. Old but not that old. The junk yards were full of parts that you might need. Our 1929 with the Sears rebuilt drives very nicely at well over 50 MPH. I just don’t like pushing it. It has given us 42 years of service, engine has been in the car over 50 years. Compare that to a rebuilt of today lasting 1,000 to 3,000 miles. How many times have we heard that complaint. Poor quality today and in 1960. It happens. But just because it was rebuilt in the 60’s does not mean it is poor quality. Sears short block 1963 price $199.95. What would that be today? $2,500.00 to $3,000.00. Last edited by WHN; 07-21-2021 at 06:15 PM. |
|
07-21-2021, 07:04 PM | #48 |
Senior Member
Join Date: May 2010
Posts: 2,791
|
Re: 3rd engine failure...getting frustrated
I checked the US Govt web site on Inflation, that $75 in 1960 ( and I'm guessing I don't recall just how much I saw them listed for!) is something like $688 today.
Yeah I have to admit, today at that price I'd be afraid to push the car even over 20MPH |
07-21-2021, 07:09 PM | #49 | |
Senior Member
Join Date: May 2010
Posts: 2,791
|
Re: 3rd engine failure...getting frustrated
Quote:
I looked it up it would be $1835 in today's money. But as you said parts were a lot more plentiful in the 60's than today. Sorry for leading this post astray I got it headed in the wrong direction. Let's get back to the original post Terry's new block holds some exciting promises. I think his second order of 500 will sell out pretty fast. |
|
07-21-2021, 07:15 PM | #50 |
Senior Member
Join Date: May 2016
Location: Scottsdale, Arizona
Posts: 615
|
Re: 3rd engine failure...getting frustrated
Good afternoon...I looked on the inflation calculator and that $200 short block in 1963 would be $1,750.00 today. So depending on who did the installation and what knot...the final package might well be close to $3,000 in today's money...Ernie in Arizona
|
07-21-2021, 07:23 PM | #51 |
Senior Member
Join Date: Mar 2012
Location: Ohio
Posts: 1,987
|
Re: 3rd engine failure...getting frustrated
The high-school parking lot comment above... I used to work with an engineer here, and he told me he drove a Model-A back-n-forth to college all 4-years. I guess plenty of people drove them as daily drivers for quite some time.
|
07-21-2021, 09:24 PM | #52 | |
Senior Member
Join Date: Apr 2013
Posts: 293
|
Re: 3rd engine failure...getting frustrated
Quote:
Suspect he buys JB Weld by the truck load. One of them was supposed to have gotten different block. He had punch marked his block. Guess what?? The new, rebuilt block he got back had the same exact punch marks. Engine crapped out after 100 miles. Like, I said earlier, don't get taken in by fancy ads, websites and videos. |
|
07-22-2021, 12:30 AM | #53 |
Senior Member
Join Date: May 2010
Location: Campbell,CA, USA
Posts: 321
|
Re: 3rd engine failure...getting frustrated
Goodcar,
Without naming the midwest "reputable" builder, can you tell us what state the rebuilder is in? Good rebuildable cores are getting hard to find and to be competitive, engine rebuilders often take shortcuts. Engine cores from areas of the USA that have freezing winter temperatures are more likely to have cracks. Please see my previous post where Bert's has to go through 12 engines to find a good core that they can rebuild economically and guarantee. |
07-22-2021, 02:36 AM | #54 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: 3rd engine failure...getting frustrated
I too would like to know who this is so you can avoid them. I think I speak for a lot of people.
__________________
"The more things change, the more they stay the same." |
07-22-2021, 07:51 AM | #55 |
Senior Member
Join Date: May 2010
Posts: 2,791
|
Re: 3rd engine failure...getting frustrated
It is best for people to PM each other about this situation.
Please do not post any names on the Forum. This needs to be kept private. In all fairness we're talking about work being done on engines nearing a hundred years old. Over that course of time these things have gone thru immeasurable stress, heating-cooling cycles etc. Henry Ford would be proud they lasted THIS long. The over all picture is summed up by 1.) Bert's has to go thru 12 engines to find a GOOD rebuildable candidate and 2.) Terry Burtz' block package is all brand new 2021 Model A Ford material. I can see where rebuilders today are scrimping trying to put together an engine for someone. The good rebuildable candidates are getting thinner by the year. Look at the labor and all Bert's invests in 11 blocks that turn out to be garbage. You have to get your money back somehow somewhere. Last edited by Jeff/Illinois; 07-22-2021 at 07:58 AM. |
07-22-2021, 10:21 AM | #56 |
Senior Member
Join Date: May 2010
Posts: 2,601
|
Re: 3rd engine failure...getting frustrated
I agree with Jeff that posting names BEFORE the cause is found it is unfair to engine builders.
There are many possible causes for rebuilt engine failures besides the builder being at fault. Did you know that a few years ago in California a fellow had his USED engine lock up ... bearing failure MAYBE. They did not investigate it any further as to the cause. He bought a rebuilt engine and it also failed within a short time. As I remember Pat in Santa Cruz (Not original builder) was asked to investigate. The crankcase was empty! Pat found a green plastic pot cleaner had been stuffed inside the oil filler cap and was totally plugged up with that White gooey stuff that forms when an engine is run for MANY short trips and never warms up. After awhile the white gooey stuff hardens totally and then plugs the green plastic pot cleaner. With the breather plugged or restricted. the crankcase pressure builds up and forces all of the oil out the rear main bearing. Same thing when someone puts oil in engine and slams the breather cap back down and bends the tabs in cap blocking the air coming out of breather tube. There is a service bulletin on this where tabs in the cap were reinforced During the discussion an engine builder said he had seen all of oil forced out the rear main when breather was plugged. This will happen in 70 miles ... YES 70 miles. That is just what happened in this case. Customer installed the rebuilt engine and tested the engine and changed the oil then left on a tour. He only got 70 miles and the engine seized up. When Pat asked the owner he said that he had just moved the breather tube from one engine to the next one without checking it. I wonder what the odds are that the first engine ran out of oil also! As I remember Pat said it was so plugged that he could not blow air through the cap. Stuffing steel wool in breather cap is the worse thing that you can do. The water vapor collects on steel wool which rusts and the small pieces of steel fall into oil pan and get into the bearings. In this case: these were NOT copper cleaners or steel wool they are plastic fiber pot cleaners. The lesson here is to find cause of the failure before proceeding! Ten years later many folks will only remember that the builder was at fault not what the real cause was! So wait until the real cause is found before blaming someone. These kind of things spread like wildfire on Farsebook and by then the untruth can NEVER be rolled back. Last edited by Benson; 07-22-2021 at 12:09 PM. |
07-22-2021, 10:29 AM | #57 | |
Senior Member
Join Date: Apr 2013
Posts: 293
|
Re: 3rd engine failure...getting frustrated
Quote:
|
|
07-22-2021, 12:21 PM | #58 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,528
|
Re: 3rd engine failure...getting frustrated
Quote:
IMO, the rebuilder I think you are describing basically sells his engines on price-point. He wants to be, or near the lowest price of his competitors. Being brutally honest with you, even though it appears he can produce a great product (-because he does have many out there), my shop cannot compete with him on pricing. Because of that, I do lose some jobs to his shop. The issue in most situations is, that potential customer for me was more interested in going the route of the lower price vs. paying for the extra steps to ensure a top-quality rebuild. It is only after there is a problem that the customer starts looking for others to place blame instead of admitting where they went wrong in their decision making. Maybe where they went wrong was choosing the cheaper option, -or maybe not asking enough questions, -or maybe not having a concise agreement on the scope of work, ...or several of those maybes. While none of us will likely ever know the full extent of what happened with your friend's engine, -nor will we hear both sides to factually establish where the blame lies, I do think it is very fair to say that in many instances there are assumptions made in a business deal that were never part of the discussion. I have found that taking extra time to digitally document the condition of a component from many angles and writing the scope of requested work in exacting detail is the way to circumvent these misunderstandings. Even then, expectations and disagreements can be an issue. I also think it is fair to share how I was recently involved with one of this shop's unhappy customers where the engine had a massive oil leak and a clutch chattering issue. I was contacted and asked if I would repair the problem. That shop's customer was frustrated because they had sent it back twice and it still had the same issue after being returned. I agreed however I suggested that he work thru it until there was no resolution. In defense of that shop, the owner stood behind it on the 3rd trip back. He corrected the issues and paid the transportation expenses for the customer. I think that says a lot about the shop owner's character in that he tried to do the right thing when mistakes were made. Rarely does this type of 'word on the street' get told, but I do think it does need to be shared more often. Unless you have the ability to walk on water, we all are going to have mishaps and malfunctions happen. |
|
07-22-2021, 01:47 PM | #59 | |
Senior Member
Join Date: Apr 2013
Posts: 293
|
Re: 3rd engine failure...getting frustrated
Quote:
|
|
07-22-2021, 01:57 PM | #60 | |
Senior Member
Join Date: Mar 2017
Location: Connecticut Shoreline
Posts: 1,824
|
Re: 3rd engine failure...getting frustrated
Quote:
We’re to old to worry about others comments. Enjoy. Haze Gray and Underway! |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|