Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 06-06-2015, 12:26 AM   #1
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Radius ball shim

I can't find my answer on existing posts, so I'll ask afresh to all the Model A Wizards... I seem to have no appreciable CASTOR, so I purchased a hemi-spherical cup-like shim with a hole in it from Brattons. Then, I found a really dumb You Tube video of some guys in Mass. "RichPins" installing it UNDER THE BALL! [Jeepers, these guys don't know how to communicate, and the dad gives rediculous half answers to his son, like "I don't know, I tighten it till it feels good"]. I'm convinced they are wrong and "bass-ackwards". Shouldn't it go OVER the radius ball? Only OVER the ball would push the ball down (lower it) and change the castor. Am I wrong or right here?
Also, is it fairly easy to pull the radius ball down to get this cup over the top of the ball (felt pad too)?
~ Chuck
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Old 06-06-2015, 12:53 AM   #2
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Radius ball shim

Given that most of the wear happens on the top of the ball, I agree with you but for a different reason. It should go on the top.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-06-2015, 05:38 AM   #3
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Radius ball shim

Yes, it should go on the top for both reasons. But, it won't add very much caster. Make sure the rod to axle attachment is tight/correct also. Caster should be around 5º.
Patrick L. is offline   Reply With Quote
Old 06-06-2015, 08:04 AM   #4
Joop
Senior Member
 
Joop's Avatar
 
Join Date: May 2010
Location: Glendale, AZ
Posts: 2,939
Default Re: Radius ball shim

Maybe you should also check if you have the original Radius Rod socket set or the later replacement.


Ps. I am from Massachusetts
Joop is offline   Reply With Quote
Old 06-06-2015, 08:31 AM   #5
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Re: Radius ball shim

Ok, Thanks. I put it in wrong, due to "You Tube University". ~ Chuck
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Old 06-09-2015, 12:44 AM   #6
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Re: Radius ball shim

Sponsored Links (Register now to hide all advertisements)
I redid the radius ball shim, putting it on top. WHAT A DIFFERENCE! I measured the caster. now, it is exactly 5 degrees forward. [I don't know what is measured before, but the car tracks forward much better; no more wandering, no more swimming.
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Old 06-09-2015, 01:10 PM   #7
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Radius ball shim

Quote:
Originally Posted by Henry's Lady's Man View Post
I redid the radius ball shim, putting it on top. WHAT A DIFFERENCE! I measured the caster. now, it is exactly 5 degrees forward. [I don't know what is measured before, but the car tracks forward much better; no more wandering, no more swimming.
Tiny bit of caster change probably DIDN'T do much to improve it. Taking the ball slack out of it was what REALLY helped. Be SURE to rub heavy grease on the BALL! Like "they" say, if it moves, grease or lubricate it!
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 06-09-2015, 09:03 PM   #8
Bruce,Upstate NY
Senior Member
 
Join Date: May 2010
Location: Odessa, NY
Posts: 385
Default Re: Radius ball shim

Regarding caster; are there any "axle twisters " left in upstate N.Y. The one in Williamsport, Pa. can't do A's, only trucks.
Bruce,Upstate NY is offline   Reply With Quote
Old 06-10-2015, 06:56 PM   #9
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: Radius ball shim

Any large truck repair/spring shop might be able to help??
Paul in CT
1931 flamingo is offline   Reply With Quote
Old 06-10-2015, 11:47 PM   #10
pat in Santa Cruz
Senior Member
 
pat in Santa Cruz's Avatar
 
Join Date: May 2010
Location: santa cruz, calif
Posts: 2,011
Default Re: Radius ball shim

it will work its way to the bottom unless you tack weld it up top.
pat in Santa Cruz is offline   Reply With Quote
Old 06-16-2015, 11:41 PM   #11
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Re: Radius ball shim

Quote:
Originally Posted by BILL WILLIAMSON View Post
Tiny bit of caster change probably DIDN'T do much to improve it. Taking the ball slack out of it was what REALLY helped. Be SURE to rub heavy grease on the BALL! Like "they" say, if it moves, grease or lubricate it!
Bill W.
Thanks, Bill. I will put some heavy axle grease on it, even though it's supposed to be lubricated from the top. I guess if they got enough grease from the top, they wouldn't wear out... right?
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Old 06-17-2015, 06:31 AM   #12
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Radius ball shim

Slack in the radius ball gets "overlooked" many times! Just think, with a loose ball, if you welded a TILLER handle to the rear of the radius rods, you could LITERALLY "STEER" the car with it!
You also have to KNOW if the socket set up is original, or the larger set up, that was designed to accommodate the rubber ball.
Another, often overlooked thing, is loose nuts that secure the steering arms to the spindles, usually causing a side to side "WOBBLY" FEELING, at "MID" speeds!
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 06-18-2015, 11:14 PM   #13
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Re: Radius ball shim

Quote:
Originally Posted by BILL WILLIAMSON View Post
Slack in the radius ball gets "overlooked" many times! Just think, with a loose ball, if you welded a TILLER handle to the rear of the radius rods, you could LITERALLY "STEER" the car with it!
You also have to KNOW if the socket set up is original, or the larger set up, that was designed to accommodate the rubber ball.
Another, often overlooked thing, is loose nuts that secure the steering arms to the spindles, usually causing a side to side "WOBBLY" FEELING, at "MID" speeds!
Bill W.
Good advice. I believe my car is fairly original, and the steel radius ball is still there... no evidence of ever having a rubber conversion. I fixed all my wobble by redoing spindle balls and drag link ball, with new (shorter) pitman arm, and new kingpins and bushings. The brakes are all redone, with Flathead Ted stuff in it.
One last fix: cast iron drums tomorrow, and I'm in tall cotton!
Chuck
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Old 06-18-2015, 11:25 PM   #14
Henry's Lady's Man
Senior Member
 
Henry's Lady's Man's Avatar
 
Join Date: Apr 2015
Location: Albuquerque, NM
Posts: 441
Default Re: Radius ball shim

Quote:
Originally Posted by pat in Santa Cruz View Post
it will work its way to the bottom unless you tack weld it up top.
Pat, Seriously???

I'm not refuting you, but I never heard of, or considered that the shim would work its way down. The hole in the center is clearly intended to pass lubricant from "on high" onto the ball. If the shim ishifts downward, that would be a design flaw, I'm thinkin'. Then again, a shim was not in the original engineering. You could be right.
__________________
... prosperity is not the product of charity but of industry - HENRY FORD
Henry's Lady's Man is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:42 AM.