Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-25-2019, 04:41 AM   #1
Neil Mylar LakewoodCA
Senior Member
 
Neil Mylar LakewoodCA's Avatar
 
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,338
Default My brothers 29 AA tanker truck overheated w/ cherry red manifold

My youngest brother owns a 1929 AA tanker truck. It's been sitting in his back yard for years (see pictures). It would overheat and get so hot that the exhaust manifold turned cherry red. He removed the muffler to see if it made any difference and it did not. He removed and cleaned out the radiator. Made no difference. He removed the timing cover and found that the spring inside the plunger was broken and that the timing gear was probably moving in and out. He wondered if that could have changed the timing making it overheat. The truck has been sitting for years with the timing cover still off and a plastic tarp over the motor.
Have any of you experienced a cherry red exhaust manifold and if so, what was the cause?
I wonder if at one time a squirrel or a mouse had stored some nuts or food in the motor's water jackets?
Any ideas would be much appreciated?
He is thinking of selling the truck, but wants to correct the overheating problem and get it running first.
Attached Images
File Type: jpg 20190224_150649.jpg (92.9 KB, 155 views)
File Type: jpg 20190224_150444.jpg (104.6 KB, 147 views)

Last edited by Neil Mylar LakewoodCA; 02-25-2019 at 04:46 AM.
Neil Mylar LakewoodCA is offline   Reply With Quote
Old 02-25-2019, 04:55 AM   #2
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

If it has been sitting for a while, I would say the rodents got to it. Those things can reak havock on whole cars. On one of my other cars, mice climbed all the way up from the tail pipe to the engine. So they will find a way in.
chrs1961815 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-25-2019, 06:45 AM   #3
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Quote:
Originally Posted by chrs1961815 View Post
If it has been sitting for a while, I would say the rodents got to it. Those things can reak havock on whole cars. On one of my other cars, mice climbed all the way up from the tail pipe to the engine. So they will find a way in.
Maybe they do but I doubt that would cause a hot manifold.
The first thing I'd do is check the ignition timing. Your brother is advancing the ignition once the motor is running, isn't he?
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 02-25-2019, 06:45 AM   #4
macdonge
Senior Member
 
macdonge's Avatar
 
Join Date: May 2015
Location: Frelighsburg, QC
Posts: 165
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

A cherry red exhaust manifold is typically a symptom of running the engine with retarded timing.


Sent from my iPhone using Tapatalk
macdonge is online now   Reply With Quote
Old 02-25-2019, 06:57 AM   #5
updraught
Senior Member
 
updraught's Avatar
 
Join Date: Feb 2015
Location: Australia
Posts: 1,966
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

running lean
updraught is offline   Reply With Quote
Old 02-25-2019, 07:43 AM   #6
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,173
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Sponsored Links (Register now to hide all advertisements)
Either or both of above. Stuck exhaust valve possibly.


Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Old 02-25-2019, 10:03 AM   #7
1930artdeco
Senior Member
 
1930artdeco's Avatar
 
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,548
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

I burned all of the rust off my mustangs exhaust manifold once while driving to the coast. I found about an inch or so of slop in the timing chain. So that is my guess.


Mike
__________________
1930 TownSedan (Briggs)
1957 Country Sedan
1930artdeco is offline   Reply With Quote
Old 02-25-2019, 10:46 AM   #8
eagle
Senior Member
 
eagle's Avatar
 
Join Date: Aug 2011
Location: Eagle Bend, MN
Posts: 2,025
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Timing is off.
__________________
"There are some that can destroy an anvil with a teaspoon and shouldn't be allowed to touch anything resembling a tool."
eagle is offline   Reply With Quote
Old 02-25-2019, 11:44 AM   #9
burner31
Senior Member
 
burner31's Avatar
 
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Yes to all the above
Another thing to check is the air filter...if you're running one...pull it off
__________________
Keith
Shawnee OK
'31 SW 160-B
burner31 is offline   Reply With Quote
Old 02-25-2019, 11:46 AM   #10
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

I had a cherry red exhaust manifold on a Model T one time when I was a teenager, it happened because I had drained the water out of it so it wouldn't freeze overnight and then forgot to refill it. lesson learned.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 02-25-2019, 11:48 AM   #11
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Check points gap and the initial distributor timing . Points gap should be set to factory specs of 18 to 22 thousants . Points gap has an effect on timing . Too small of a points gap retards the timing . I mostly use the larger .022 gap because it allows the points to open quicker , if initial timing is correct . Try removing all of the spark plugs to remove compression . Remove the timing pin and turn the engine over until the timing pin drops into the timing dimple on the timing gear . loosen the cam screw and adjust the distributor cam so that the trailing edge of the rotor tip points exactly at the number one contact in the distributor cap . There will usually be some rotational slack or free movement in the distributor shaft . This rotational movement is sometimes referred to as backlas h. Make sure that ALL of the backlash is in the counter clockwise direction when the cam screw is tightened . Being as the distributor shaft rides on the clockwise side of the backlash , any free rotation in the clockwise direction causes the engine to have to turn a small amount to catch up the slack before the distributor shaft begins to turn and the timing will be retarded to whatever amount of backlash that remains in the clockwise direction after the cam screw is tightened . A lot of people never understand how clockwise backlash in the distributor shaft effects timing and that is the reason that many model A's are out of time , lack power and the manifold turns cherry red . Again , being as the distributor rides on the clockwise side of the backlash , any clockwise backlash in the distributor shaft after the cam screw is tightened retards timing .Back lash in the counter clockwise direction after tightening the cam screw will have NO effect on timing or anything else . A cam wrench comes in very handy at holding the distributor cam while the cam screw is tightened. Close attention to direction of distributor backlash has a big effect on timing .
Purdy Swoft is offline   Reply With Quote
Old 02-26-2019, 12:27 AM   #12
Neil Mylar LakewoodCA
Senior Member
 
Neil Mylar LakewoodCA's Avatar
 
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,338
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Thanks everyone for your advice.
I will pass this information onto my brother and will let you know what happens.
Neil Mylar LakewoodCA is offline   Reply With Quote
Old 03-22-2019, 10:38 PM   #13
Neil Mylar LakewoodCA
Senior Member
 
Neil Mylar LakewoodCA's Avatar
 
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,338
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Here is an update.
My brother found and removed mouse debris in the timing cover area. He replaced the missing thrust plunger and broken spring. He removed the valve cover and the oil pan and removed built up sludge. He re-set the timing which was off. The motor runs much better and it no longer overheats.
Neil Mylar LakewoodCA is offline   Reply With Quote
Old 03-22-2019, 10:44 PM   #14
Neil Mylar LakewoodCA
Senior Member
 
Neil Mylar LakewoodCA's Avatar
 
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,338
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

By the way, he has decided to sell the truck. I'm going to list it in the swap section soon.
Neil Mylar LakewoodCA is offline   Reply With Quote
Old 03-22-2019, 11:30 PM   #15
Bill Cilker
Senior Member
 
Bill Cilker's Avatar
 
Join Date: Apr 2011
Location: Milpitas, CA
Posts: 396
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Neil
Your brother's truck is an early 1930 truck made between January and June of 1930. It has he bevel gear rear axle and the heavier duty front axle. The 5 hole budd wheels were first used starting January 1930. The 28-29 style cab was used through June of 1930.
__________________
Bill Cilker, Jr
Unrestored 190A Victoria
45B, 160B & 189A
Victoria Association President

Last edited by Bill Cilker; 03-23-2019 at 12:16 PM.
Bill Cilker is offline   Reply With Quote
Old 03-23-2019, 04:18 AM   #16
john charlton
Senior Member
 
john charlton's Avatar
 
Join Date: May 2010
Posts: 1,304
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

I lent my AA truck out it smelt hot on its return .I lifted the hood and the manifold was cherry red .On the 5 mile return journey the driver had forgotten my instructions and had not advanced the timing so it ran fully retarded for about twenty minutes on country roads slow drive.The truck was not boiling but close I guess . This was years ago the truck runs well so no lasting harm done it seems .

John in settled high pressure weather Suffolk County England.
john charlton is offline   Reply With Quote
Old 03-23-2019, 11:53 AM   #17
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

This is a good reason not to let anybody drive your model A unless you are in there with them . Some will badly lug the engine while thinking that they are going easy on it .. Many don't know what lugging actually is .
Purdy Swoft is offline   Reply With Quote
Old 03-23-2019, 12:53 PM   #18
Neil Mylar LakewoodCA
Senior Member
 
Neil Mylar LakewoodCA's Avatar
 
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,338
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Bill,
Thanks for the info.
Yes, my brother looked up the number and it is a January 1930. The motor and frame number match.
Surprisingly, it has the high speed beveled rear end.
Neil Mylar LakewoodCA is offline   Reply With Quote
Old 03-23-2019, 01:24 PM   #19
ursus
Senior Member
 
Join Date: May 2010
Location: Oregon
Posts: 1,369
Default Re: My brothers 29 AA tanker truck overheated w/ cherry red manifold

Quote:
Originally Posted by Neil Mylar LakewoodCA View Post
Here is an update.
My brother found and removed mouse debris in the timing cover area. He replaced the missing thrust plunger and broken spring. He removed the valve cover and the oil pan and removed built up sludge. He re-set the timing which was off. The motor runs much better and it no longer overheats.
The thrust plunger and spring replacement was the critical factor in this repair. Absent that, no amount of fiddling with the distributor would have been effective for very long. I struggled with this same problem until I discovered the cause. I would set timing, drive for a few miles until engine runs rough and overheats, then reset timing, drive for a few miles, etc., etc.
ursus is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:30 AM.