|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-07-2020, 01:37 PM | #1 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Quick question re valve springs.
Hello!
Just a quickie. If you have a valve spring with closely wound coils at one end only, should the end with the tightly wound coils go towards the guide, or the keeper?? Or does it not matter which way around they are fitted? Thanks in advance. Mart. |
12-07-2020, 02:20 PM | #2 |
Senior Member
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,528
|
Re: Quick question re valve springs.
Mart the closely wound end of the spring goes towards the retainer/ keeper end.
Ronnieroadster
__________________
I use the F word a lot no not that word these words Flathead , Focus and Finish. "Life Member of the Bonneville 200 MPH Club using a Ford Flathead block" Owner , Builder, Driver of the First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921 in one and a half miles burning gasoline. First ever gas burning Ford flathead powered roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH |
Sponsored Links (Register now to hide all advertisements) |
|
12-07-2020, 02:28 PM | #3 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Re: Quick question re valve springs.
Thanks Ronnie. I used 8 of these valve springs and got 7 the wrong way around!
Got a little rework to do! Mart. |
12-07-2020, 06:29 PM | #4 |
Senior Member
Join Date: May 2010
Location: Wa.
Posts: 5,408
|
Re: Quick question re valve springs.
|
12-07-2020, 07:44 PM | #5 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Quick question re valve springs.
The tight wrapped coils go on the guide, or another description, against the block, or up.
|
12-07-2020, 08:12 PM | #6 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,312
|
Re: Quick question re valve springs.
Sponsored Links (Register now to hide all advertisements)
|
12-07-2020, 08:17 PM | #7 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: Quick question re valve springs.
I've always put the close would end to the guide. Less mass of the spring to control.
|
12-07-2020, 08:30 PM | #8 |
Member Emeritus
Join Date: May 2010
Location: Fitzgerald, Georgia
Posts: 2,204
|
Re: Quick question re valve springs.
Yes, the tight wound end goes up against the guide.
|
12-07-2020, 09:21 PM | #9 |
Senior Member
Join Date: May 2010
Location: Yakima Washington
Posts: 913
|
Re: Quick question re valve springs.
|
12-07-2020, 10:55 PM | #10 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 921
|
Re: Quick question re valve springs.
Yes, close wound coils to the stationary end of the spring.
Terry
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" 302 |
12-08-2020, 03:15 AM | #11 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Re: Quick question re valve springs.
Thanks for all the input, fellas. I'll go with the consensus.
Mart. |
12-08-2020, 10:11 AM | #12 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Quick question re valve springs.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|