|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-12-2021, 05:48 PM | #1 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Need some help identifying these hubs/drums
I realize this are early, but I am a '40 guy so I don't have much experience with older Fords. So what year or years would these be ? Thank you.
|
05-12-2021, 06:34 PM | #2 |
Senior Member
Join Date: May 2015
Posts: 8,125
|
Re: Need some help identifying these hubs/drums
They look like the ones on my '34....I think they're common to 35's as well. '32 to '35???
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
Sponsored Links (Register now to hide all advertisements) |
|
05-12-2021, 06:36 PM | #3 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,750
|
Re: Need some help identifying these hubs/drums
To my eyes they look like 32-34.
|
05-12-2021, 07:50 PM | #4 |
Senior Member
Join Date: May 2010
Location: so cal, placerville, vegas
Posts: 1,394
|
Re: Need some help identifying these hubs/drums
What width shoes would they be for?
|
05-12-2021, 08:00 PM | #5 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Need some help identifying these hubs/drums
Measure the depth for a "close" figure.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
05-12-2021, 08:36 PM | #6 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,834
|
Re: Need some help identifying these hubs/drums
Sponsored Links (Register now to hide all advertisements)
__________________
Unfortunately, two half wits don't make a whole wit! |
05-12-2021, 08:40 PM | #7 |
Senior Member
Join Date: May 2010
Location: N. GA
Posts: 531
|
Re: Need some help identifying these hubs/drums
If they measure 11 inches they are late '31...if they measure 12 inches they are '32 or later...
TOB |
05-13-2021, 03:42 AM | #8 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,750
|
Re: Need some help identifying these hubs/drums
|
05-14-2021, 07:27 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: Need some help identifying these hubs/drums
They measure about 11 3/4" in depth, so would those be A or later EV8 ? Thank you all !
|
05-14-2021, 10:15 AM | #10 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: Need some help identifying these hubs/drums
The 11" or 12" measurement referred to above is the inside diameter of the drum where the brake shoes/linings fit, not the depth of the drum/hub assembly. Further, nothing after the '32-'34 version have that identical exterior appearance.
|
05-14-2021, 10:49 AM | #11 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,750
|
Re: Need some help identifying these hubs/drums
I think it may be a mis spelling of 1-3/4" If that is the width they are 32-34 and made for 1-1/2" shoes.
|
05-14-2021, 02:15 PM | #12 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: Need some help identifying these hubs/drums
Mart,
That makes sense (that it isn't eleven, but rather one). |
05-14-2021, 05:46 PM | #13 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: Need some help identifying these hubs/drums
To clarify what I mean by depth; The width of the swept area of the brake shoe in the ID of the drum is 11 3/4". So are we in agreement they are '32-34 ? Thank you.
|
05-14-2021, 07:07 PM | #14 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,749
|
Re: Need some help identifying these hubs/drums
Like Mart said do you mean 1 3/4" width not 11 3/4" and what is the diameter?
|
05-15-2021, 09:01 AM | #15 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: Need some help identifying these hubs/drums
Sorry, the width of the swept area for the shoes in the ID of the drum is 1.750, or 1 3/4".
|
05-15-2021, 09:41 AM | #16 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: Need some help identifying these hubs/drums
The easiest dimension for establishing whether or not they are Model A drums or '32-'34 drums is the inside diameter of the swept area. If that diameter is not 12" or a slight fraction over 12" (from wear) then they are not '32-'34 drums.
|
05-15-2021, 06:38 PM | #17 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: Need some help identifying these hubs/drums
Thank you. I miked the ID of the swept area and it was 12.000", which makes sense as the OD is thick. I have several other pairs and they are all over 12.000" ID. I appreciate everyone's help and patience.
|
05-15-2021, 06:59 PM | #18 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: Need some help identifying these hubs/drums
'32-'34 and if you want to sell those measuring 12.000" that are not scarred, I'm your buyer, please.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|