|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-30-2021, 11:36 AM | #21 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,304
|
Re: The case for sacrificial anodes in your cooling system
I got mine from Amazon.com. Each piece yield 3 chunks. Here's a link : https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1.
|
07-30-2021, 12:07 PM | #22 | |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: The case for sacrificial anodes in your cooling system
Quote:
|
|
Sponsored Links (Register now to hide all advertisements) |
|
07-30-2021, 01:21 PM | #23 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,304
|
Re: The case for sacrificial anodes in your cooling system
In a perfect world, yes. However, conditions are different and can change. Who for example, has calculated the mix of materials (basically aluminum vs. iron) exposed to the coolant and determined the precise antifreeze product required for that particular combination? Nobody I know. As soon as the fresh coolant mixture has been in the engine one minute, changes are already taking place. Nothing takes the place of proper maintenance, but most people don't change their coolant once a year. For that matter, who do you know that changes their brake fluid every "two or three years" as mentioned in his post? Nobody I know. Perhaps those with a staff looking after their cars, but not most of us; this is a hobbyist forum, after all.
Look at the sacrificial anode as an indicator first and then as an insurance policy. In the first case, a casual inspection will give you an early indication if anything is starting to go wrong, and secondly, it's presence will serve as a partial cure if anything is going wrong. The anti-freeze mixture in my car was fresh 3 years ago in a clean engine. I didn't like what I saw, so a flush and refill is in order. The one thing I do know is the the material leached from the magnesium chunk did not come from the aluminum heads. I fail to see why anyone would go to such lengths to avoid such an easy, effective method of checking and controlling cooling system performance. |
07-30-2021, 02:57 PM | #24 |
Senior Member
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,627
|
Re: The case for sacrificial anodes in your cooling system
This is the one from Mac's. the little wire wraps around the brass button at the bottom of the radiator cap and the chunk of zinc drops into the water when you put the cap on. Designed to protect aluminum. Mine has shown considerable erosion over five years, so it is doing something. Cheap insurance for the Offy heads.
https://www.amazon.com/MACs-Auto-Par...7674754&sr=8-4 |
07-30-2021, 06:45 PM | #25 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,304
|
Re: The case for sacrificial anodes in your cooling system
As I have said before, the Galvanic Series table tells me that zinc is not the best anode to be used to protect aluminum. They are too close together. Magnesium is a better choice, which is why the RV's with aluminum water heater tanks use magnesium rather than zinc.
Zinc anodes are mainly for marine use, like "Floyd"'s example of a bronze propeller and a stainless steel shaft. Look at the Galvanic Series table in both situations, and try to comprehend what it is telling you. |
07-30-2021, 09:00 PM | #26 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,829
|
Re: The case for sacrificial anodes in your cooling system
Sponsored Links (Register now to hide all advertisements)
I have made and fitted 'pencil' anodes into every 24 stud engine I've built over the years [I use 1/2 dia zinc rod, thread one end 1/4 pipe and using common 3/8 NPT plugs, I tap them 1/4 NPP, then screw the zinc pencil into the plug; it then sorta resembles a post 40 temp sender unit, these screw into the boss under the centre hose outlet] My own personal engines are 37-38 blocks with the pump in heads fitted. This leaves theoriginal water pump openings in the block to be capped. Ford actually produced cast caps for this very purpose...I make my own out of 3/8 plate steel. The inside surface of these I tap to accomodate zinc 'rudder' anodes. These are big 'domed pancakes', just the right size to fit in the block openings, and provide a massive surface area with the coolant. Irrespective as to whether you choose magnesium or zinc for your anode choice, the most important thing, that hasn't been mentioned, is that they MUST make a good ground. No use just dangling it into the top radiator tank on a bit of string!
__________________
Unfortunately, two half wits don't make a whole wit! |
07-31-2021, 07:30 PM | #27 |
Senior Member
Join Date: Oct 2017
Posts: 563
|
Re: The case for sacrificial anodes in your cooling system
The "good ground" aspect is also a factor for the radiator itself, especially aluminum radiators. I'm not sure why this happens to aluminium in particular but stray voltage or current draw (as when starting the engine) or specifically electrical components "searching for a ground" can inadvertantly send serious amperage through the coolant and/or the radiator and eventually, ruin it. This damage or type of defect is not covered under warranty. The pictures I've seen of it show long dark vertical streaks externally, on the fins.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|