Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-27-2024, 11:31 AM   #1
TPR1930
Junior Member
 
TPR1930's Avatar
 
Join Date: Jun 2016
Location: Polk County, Florida
Posts: 10
Default Radiator Leak

In mid-2017, I bought a replacement heavy duty radiator (For 1930 -31, 8 Fins per inch) from Brattonís. Since then, I have put no more that 1,000 miles on my car. The radiator is filled with Sierra Safer-Formula antifreeze. Approximately 100 miles ago, I started to notice a mineral-type deposit developing beneath my radiator cap, and subsequently a leak at the junction of the overflow tube. I repaired this with a patch of metal putty, but now see that it has developed again. Brattonís has told me this is the first theyíve ever heard of this problem (they sell over 100 radiators a year), and told me to contact the maker with my questions. A call to them left on a vague answering machine has been unreturned. My question is Ö has anyone else encountered this problem? Since I donít put many miles on the car, would anyone suggest an additive that might stop this leak? I know it can be a temporary fix, with issues, but would like to hear any pros and cons. In my case, Iím not so concerned about the radiator itself, but instead, the cooling channels in engine block. I think I remember a member here mentioning a solder failure they once had, and itís been in my mind that if that is the case here, what is to guarantee that it will not continue happening elsewhere? The cost of having it recored vs. a new replacement is not an issue for me. What is, is the annoying fact that I may have to go through the double-work of replacing it. Please give me your thoughts ..
Attached Images
File Type: jpg IMG_4926.jpg (50.3 KB, 174 views)
File Type: jpg IMG_5068.jpg (44.5 KB, 178 views)
TPR1930 is offline   Reply With Quote
Old 02-27-2024, 12:01 PM   #2
Bob-A
Senior Member
 
Bob-A's Avatar
 
Join Date: May 2010
Location: Central FL, USA
Posts: 1,137
Question Re: Radiator Leak

The corrosion on the locking cap I can't help you with? I've used the Sierra
brand anti-freeze (half distilled water/half Sierra) for years with no problems.
The leak I would have used JB Weld. It has worked on a small leak on my cast iron "B" block.


Bob-A


"Skirts are for Women not car Fenders"
Bob-A is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-27-2024, 12:27 PM   #3
Ernie Vitucci
Senior Member
 
Join Date: May 2016
Location: Scottsdale, Arizona
Posts: 611
Default Re: Radiator Leak

Agree...Drain some coolent out of the radiator and use a dremell tool or some such to slightly expand and clean out the crack. Use JB Weld and let it sit for a couple of days, then put the coolent back in and fire her up and see what happens. Some of these sorts of problems come from not driving the A more often...stuff sits in the same place and tends to do damage that would not be done if the car is driven more and all of the systems exercised. Good Luck...Ernie in Arizona
Ernie Vitucci is offline   Reply With Quote
Old 02-27-2024, 12:31 PM   #4
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,900
Default Re: Radiator Leak

I would contend that the Sierra Safer-Formula antifreeze may be at fault. How often do you change it? I think it may only last a couple years. I also agree that driving the car more may help.

I am going to go with the suggestion to use JB Weld to fix the leak. Meticulously clean the area down to metal and rough it up. A small stainless wire wheel on a Dremel might be best. Then do a final clean with acetone.

Alternately, re solder the area with radiator solder.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 02-27-2024, 01:50 PM   #5
Gene F
Senior Member
 
Gene F's Avatar
 
Join Date: Mar 2012
Location: Ohio
Posts: 1,958
Default Re: Radiator Leak

Is there still a radiator shop near you? if so drive it over and ask them about it. Tell them you will pull it, and bring it to them for repair. If you start messing with it no one is gonna wanna help you fix it later. Sorry to be so blunt, but that is just a fact.

Also, either drive it more, or lose the anti-freeze.
Gene F is offline   Reply With Quote
Old 02-27-2024, 04:32 PM   #6
mercman from oz
Senior Member
 
mercman from oz's Avatar
 
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,361
Default Re: Radiator Leak

Sponsored Links (Register now to hide all advertisements)




Radiator Leak 1930 Ford Model A - TPR1930
mercman from oz is offline   Reply With Quote
Old 02-27-2024, 04:51 PM   #7
ronn
Senior Member
 
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,785
Default Re: Radiator Leak

doesnt look too great. maybe consider a diff rad cap?
ronn is offline   Reply With Quote
Old 02-27-2024, 09:02 PM   #8
brito36
Senior Member
 
Join Date: May 2010
Location: Marengo. Illinois
Posts: 262
Default Re: Radiator Leak

I don't know. If it were me, I would pull the radiator and send it to a good radiator shop to check it out, flush it, and make any necessary repairs. I would then completely flush out the block. I would use a can of Barr's Stop Leak, and then fill it with a 50-50 mixture of anti-freeze and drive it. I have done this to all my Model A's and diesel engines for over fifty years and have not had a problem. It appears that you have some type of mineral precipitate on the cap. Could be the cap's material.
brito36 is offline   Reply With Quote
Old 02-28-2024, 06:40 AM   #9
WRA
Senior Member
 
WRA's Avatar
 
Join Date: Sep 2010
Location: South of I-40
Posts: 379
Default Re: Radiator Leak

That’s nothing, if anything dissimilar metal corrosion from the cap.


Drain it out, flush good with plain water. Fill with a quart of Blue Devil Radiator flush. Do a run to temp at least 3 times over a 10 hour period. Directions say not to leave in more than 4 hours, but that’s based on modern aluminum.

Once Done, Drain and fill with a good quality 50/50 mix.

Last edited by WRA; 03-01-2024 at 05:52 AM.
WRA is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:29 PM.