46-48 ford car parts

[hooversab]

parting out 3 1946 thru 48 ford cars 1 4dr. sedan good doors, front and rear seat assemblys. decent deck lid not perfect but usable also exterior trim. 1 bussiness coupe , side mldgs, front seat some side mlgs and door parts. no deck lid . 1 47 ford 5 passenger coupe nice seats , good cowl vent, qter window assemblys . heater , windsheild trim . column shift manuel trans. sorry all 3 cars have rough dashes . some usable fenders but far from perfect complete front clips . ford script rear bumpers. email me with you parts needs maybe i can help. going to jefferson swap meet and bringing parts . thanks joe

[yblock46]

If you have shift tube bring it with you to jefferson, I should be there.
thanks
yblock46

[Juergen]

If you have the 46 grille guard (actually the license plate guard) send me a message at [email protected] I can't figure out how to get private messages.

[46fatford]

Interested in front and rear bumpers, heater and business or 5 pass coupe front seat.
Thx
Matt

[dullchrome]

Interested in the rear window stainless if you have it.

[F-6Garagerat]

Sponsored Links (Register now to hide all advertisements)

i need 2 open drive transmission yokes

[GaLi]

Joe:
I'd like to talk to you about a few parts I'm looking for. Please call me, Gary, at (303) 665-5531 and leave your telephone number or email. Thanks.

[47Fordvert]

If you happen to have the passenger side interior windshield trim (garnish) would you let me know? Also a price. Thanks. Larry

[Graeme / New Zealand]

need a complete speedo " turtle" drive number "19".

Thanks

GB

[The Zoomer]

Hello Looking for front hubs, please email me at [email protected] thanks

[The Zoomer]

Nevermind Hooversab, I found some. Thanks

[needparts10]

looking for e-brake actuating arm's for inside rear drum's 1942-48 ford two' L' shaped, two 'CRESENT' shaped thank's [email protected]

[pdgtx4]

If you still havethe cars, I'm interested in the heater, air cleaner, distributor and plug wire tubes if available. Thanks - Ron.

[Tejas34]

I am interested in the 1947 5 window Coupe rear seat, and a drivers side rear fender. I am building a Coupe, which I need the back seat for and my brother is building a 2-dr sedan which he needs the rear fender.
.
If these are not sold yet, could you send me a picture and shot me a price.

John Stanford
Towanda, KS

[peewee2you]

looking for smooth stainless running board trim only? I say smooth only because I am not sure if on a 46 it has that line in it like the body belt trim, and I have a 47 which is all smooth stainless. The running board trim doesn't need to be all that perfect itself, I am missing one side, and although I have new replacement don't want to use them til I have it painted, so let me know what you want for the pair if you don't want to sell only one, so either way if you have it let me know.

Thanks,
Pete
Elk Grove, CA

[chrisbob12]

Can send me a picture of the Business Coupe front seat and price. I'm in Nevada City, Ca. Along ways but if the seat is decent I"m interested.
Thanks, Bob.

[RAYSSUPERDELUX]

Hi- i could use a '48 driver's side rear fender-

thanks, ray empire, mi

[hooversab]

hi i will check i have the fender with the gas opening that is the left fender correct ? $100 pluse freight send me your email address and i will send photo thanks joe

[studebaker]

Hi, I'am looking for rear axle complete. Live in the UP pick up no problem. [email protected]

[peewee2you]

I never received an answer to my post?
Thanks,
Pete