|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-14-2020, 01:32 PM | #1 |
Senior Member
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,346
|
Gap at wishbone to bell housing
I can't seem to get rid of the gap at the wishbone to bell housing area.
Is this gap normal or should I be concerned? If so, how do I fix it? I dont remember seeing this gap in the past. |
10-14-2020, 01:47 PM | #2 |
Senior Member
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,339
|
Re: Gap at wishbone to bell housing
Look just like mine, not a problem.
__________________
Ruth "Sometimes you really DO need to read the whole thread" |
Sponsored Links (Register now to hide all advertisements) |
|
10-14-2020, 04:48 PM | #3 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,184
|
Re: Gap at wishbone to bell housing
That means your ball is not worn out-a good thing
John
__________________
Welcome each day |
10-14-2020, 05:38 PM | #4 |
Senior Member
Join Date: Sep 2017
Location: Mint Hill, North Carolina
Posts: 386
|
Re: Gap at wishbone to bell housing
The gap means that the bottom clamp is under spring pressure to hold the wishbone ball in place, which is normal.
If you didn't have any gap remaining... that's when you start having a problem. |
10-14-2020, 07:47 PM | #5 |
Senior Member
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,346
|
Re: Gap at wishbone to bell housing
Actually there are two gaps.
One between the bell housing and the inside, upper cup. Then one between the upper cup and the lower cup. Are you sure that is normal? |
10-14-2020, 08:34 PM | #6 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Gap at wishbone to bell housing
Sponsored Links (Register now to hide all advertisements)
The ball retainer has larger holes than the bolt by a considerable amount. There are actually annular "sleeves" which the ball retainer slides over: the springs are outside of these and on the lower side of the ball retainer. The nuts are held from compressing the springs "solid" by these sleeves. The proper setup has the nuts as tight as they can be, the compressed spring with small gap between the turns, and a small gap between ball seat and ball retainer. It is possible if there is considerable downward force on your wishbone that it could compress the springs, cause the ball retainer to drop, loosen the contact between the ball and its ball seat, and a gap to form between the ball seat and the bell housing. This I would consider unusual. And possibly a reason to replace at least the springs which in time may lose their compression. This quite a bit different from the aftermarket ball caps which when assembled are "solid" - and the make-up made in the rubber ball. Joe K
__________________
Shudda kept the horse. |
10-15-2020, 02:12 AM | #7 |
Senior Member
Join Date: May 2010
Posts: 1,304
|
Re: Gap at wishbone to bell housing
From your picture it looks to me that the bottom retainer is cast iron not pressed steel . This is the aftermarket rubber ball setup which I myself am not a fan of . With the all steel setup you can see what is going on with the hidden rubber ball you cannot . The reason that the rubber ball setup is used is because of excess wear on the radius ball (gone oval) If the ball is oval the parts houses sell a shaped washer to take up the slack . If it were my car i would ditch that setup and go back to standard .
John still in thanks to Covid 19 Suffolk County England . |
10-15-2020, 02:20 AM | #8 |
Senior Member
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,346
|
Re: Gap at wishbone to bell housing
John,
I have the original set up. The upper cup is cad plated. See picture from Brattons online catalog. |
10-15-2020, 09:30 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 1,304
|
Re: Gap at wishbone to bell housing
Looking again I can see OOOOPS !!!
John in same place same weather . |
10-22-2020, 04:04 PM | #10 |
Member
Join Date: May 2010
Location: St. Paul, MN
Posts: 45
|
Re: Gap at wishbone to bell housing
The sleeves are supposed to hold the upper cap firmly against the bottom of the bell housing. I would look for some interference between the upper cap and bellhousing that is preventing the cap from seating tightly at the bellhousing.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|