|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-13-2020, 08:02 AM | #1 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,743
|
Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 Pt 19
Hello! Welcome to some Early Ford Tech from Mart's Garage. How can you tell if your driveshaft is running true? How about the torque tube?? Is it square to the axle? Well, I'll show you a method that has worked for me. Best of all, it doesn't require any fancy equipment. Mind reeling from all that tech? Lets bust out the vintage Buma valve seat tool and show the O'l 59 flatty what for.
Thanks for checking in, hopefully some of this tech stuff will help someone out there. Catch you on the next one! Mart. https://youtu.be/eTmxoFgBlUU Last edited by Mart; 11-13-2020 at 09:35 AM. |
11-13-2020, 11:30 AM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,919
|
Re: Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 P
Mart, thanks for posting that very informative video. I really like that you show the entire process including how to correct the "over bend" mistake. Do the built up weld beads on the banjo end of the drive shaft present any problems? Do you grind them down smooth or leave them? Please refresh our memories as to what year make and model you are working on that required you to undertake this drive shaft modification. Thanks.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-13-2020, 01:32 PM | #3 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,743
|
Re: Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 P
Cheers Fordy.
The axle, driveshaft and torque tube are going into my 32 sedan. The axle is Ford Pilot, very similar to 35/36 US Ford. The torque tube is shortened 35/36 Ford. I did have a driveshaft but it was too long and also had a dent so I opted to lengthen an Allard driveshaft. I lengthened it by welding a 6 spline coupler to the end. I've covered all the steps over the last few weeks in my videos. Mart. |
11-14-2020, 12:03 PM | #4 |
Senior Member
Join Date: May 2010
Location: At my kitchen table in Santa Rosa, Ca
Posts: 2,903
|
Re: Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 P
Hi Mart! thanks for the Vid's i think they are very interesting! keep up the hard work. are we gonna get crusty flatty 2 running? i hope so
__________________
If it would have been a snake it would have bit ya! i can't spell my way out of a paper bag! |
11-15-2020, 08:24 AM | #5 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,623
|
Re: Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 P
Good show Mart!!....I wondered about just using a torch instead of welding.....the first time I saw that being done, I was hauling 50 foot I beams for new bridge construction. There was an iron worker heating one side of a beam with a huge torch and I asked what that was for. He said he was straightening it. It would expand and come back further to where he wanted it. I’ve always been intrigued by watching people who know what their doing! Thanks for having us in Mart’s Garage.........Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
11-15-2020, 10:59 AM | #6 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Early Ford Torque Tube and Driveshaft Alignment How To. Flatty Valve Seats. 32 P
Sponsored Links (Register now to hide all advertisements)
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|