|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-08-2017, 05:58 PM | #1 |
Senior Member
|
Need 6V gas tank sending unit rebuilt
Any information on reliable source to rebuild my 50 Ford gas tank sending unit would be appreciated.
|
05-08-2017, 06:27 PM | #2 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Need 6V gas tank sending unit rebuilt
You might try some of the instrument shops. If they can repair the King Seeley indicators then the sender should be near the same construction. If you pop the cap off the to of the sender, you can see the bi-metallic strip and the little contact points set. They have a calibration resistance spool in there too. Sometimes they just need the little points cleaned up.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-08-2017, 07:31 PM | #3 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Need 6V gas tank sending unit rebuilt
The K/S units insides look like this 1940 unit.
If you find a rebuilder please let us all know. |
05-08-2017, 08:57 PM | #4 |
Senior Member
Join Date: Sep 2010
Posts: 350
|
Re: Need 6V gas tank sending unit rebuilt
i sent an original 38 packard sending unit in to get rebuilt by so called experts a fewyears ago.what i got back was a cheap generic sender cobbled onto the original holder didnt work for s..t b careful and ask first.
|
05-09-2017, 01:44 AM | #5 | |
Senior Member
Join Date: May 2010
Location: Melbourne Australia.
Posts: 2,079
|
Re: Need 6V gas tank sending unit rebuilt
Quote:
Hi there, May I ask why you think it requires rebuilding or more accurately to be repaired or tested. Have you tested the sender unit or the dash gauge and wiring ? You can lever the top off the sender unit carefully and inspect the contact points at the end of the bi-metal strip . Clean them carefully without bending anything with a fine strip of doubled over wet and dry paper. Also inspect the fine coil winding to see if it has been overheated or burnt. If it is all burnt then the unit is more than likely is unrepairable. On no account make alterations to the gear wheel adjustment. Check the contact point under the cover is clean. Make sure the sender unit and fuel tank has a good ground to the chassis. Regards, Kevin. |
|
05-09-2017, 05:58 AM | #6 |
Senior Member
|
Re: Need 6V gas tank sending unit rebuilt
Sponsored Links (Register now to hide all advertisements)
|
05-09-2017, 06:39 AM | #7 |
Senior Member
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
|
Re: Need 6V gas tank sending unit rebuilt
Most old Ford fuel senders I worked on have a resistance of 0 to 74 ohms.
Use an ohmmeter from the body of the sender to the terminal screw. It should move in the range above as you move the float up and down. G.M.
__________________
www.fordcollector.com |
05-09-2017, 10:20 AM | #8 |
Senior Member
Join Date: Jul 2014
Location: Guston,ky
Posts: 653
|
Re: Need 6V gas tank sending unit rebuilt
The one i bought from Bob Drake said it worked 6
6 or 12 volt. May look into a nude one to see |
05-09-2017, 11:09 AM | #9 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Need 6V gas tank sending unit rebuilt
King Seeley won't work well off resistance alone. They work off current and pressure. Current for the heating element and pressure against the bi-metallic strip. The amount of pressure on the bi-metallic strip is reproduced in the indicator unit with pressure against the indicator needle.
If you replace the sending unit with a rheostat type unit, you have to change the instrument to that type as well to get full accuracy throughout the range of meter movement. Last edited by rotorwrench; 05-09-2017 at 12:04 PM. |
05-09-2017, 11:16 AM | #10 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
|
05-09-2017, 12:39 PM | #11 |
Senior Member
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
|
Re: Need 6V gas tank sending unit rebuilt
What points???? G.M.
__________________
www.fordcollector.com |
05-09-2017, 01:02 PM | #12 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
The points in the sender. Current is regulated in the sender by opening and closing a set of points (contacts). The rate at which they are opening and closing determines the current in the system between the sender and the gauge. The float position changes the tension on the point and thus the rate they vibrate. If the points are open the resistance will be zero and if closed, a very low value based on the coil (windings around the bimetal strips). There should be no change in the resistance once the points close regardless of the float position. The attached operation description is related to Mercury/Lincoln units, but they all functional work the same.
Last edited by JSeery; 05-09-2017 at 02:53 PM. |
05-09-2017, 07:22 PM | #13 |
Senior Member
Join Date: May 2010
Location: Melbourne Australia.
Posts: 2,079
|
Re: Need 6V gas tank sending unit rebuilt
GM, You are thinking of the later type sender unit (late 1950s on) which is a variable resistance or rheostat type. The senders used from 1936 to the 1950s are the type made by King Seeley and have contacts and a heated bi-metal strip inside and work in a chopping on/off switching system as described by JSeery and rotorwrench in the previous posts. Regards, Kevin.
|
05-09-2017, 07:48 PM | #14 |
Senior Member
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
|
Re: Need 6V gas tank sending unit rebuilt
The sender in my 36 gives an ohms reading of about 17 ohms which is about
3/4's of a tank. I have a loose sender that reads from 0 to 24 ohms. I have a loose sender that also measures 0 to 24 ohms. When clipped with jumper wires to my gauge the gauge go's from empty full. Never had the sender out of the tank, it's a roadster and not that easy for me to get at. G.M.
__________________
www.fordcollector.com |
05-09-2017, 08:33 PM | #15 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
Must be a replacement unit that uses resistance.
|
07-14-2017, 02:34 PM | #16 |
Senior Member
Join Date: Mar 2014
Location: Webster, NY
Posts: 215
|
Re: Need 6V gas tank sending unit rebuilt
I made the same mistake of buying a sending unit from Mac's and discovering that it does not work well. The problem turned out to be a rusted out float in the original unit. It looks just like the pictures that 19 Fordy posted. I also got resistance readings of around 10 to 74 ohms from it. I would like to clean up or have the unit professionally cleaned up and calibrated before I drop the tank and reinstall it. I jumpered it to the gauge wire and grounded it and the fuel gauge read 7/8 full with the float all the way up and empty with the float all the way down. Morris Gauge had been recommended at one time but their website is defunct. Any thoughts?
|
07-14-2017, 03:34 PM | #17 | |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,779
|
Re: Need 6V gas tank sending unit rebuilt
Quote:
|
|
07-14-2017, 03:55 PM | #18 | |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
Quote:
Ford up to 1986 - 73-10 Ohms Ford 1987 & up - 16-158 Ohms GM up to 1964 - 0-30 Ohms GM 1965-1997 - 0-90 Ohms GM 1998 & up - 40-250 Ohms Mopar up to 1986 - 73-10 Ohms AMC 1950-1977 - 73-10 Ohms Autometer -240-33 Ohmswww.jalopyjournal.netis the most common however other ohm ranges are made Classic Instruments - 240-33 Ohmswww.jalopyjournal.net(excluding vehicle specific gaugewww.jalopyjournal.netkits which use factory ohm range) Dolphin - 0-90 Ohms Dakota Digital - Programmable to work with most Ohm range senders VDO - 10-180 Ohms King-Seegley work with points, they are either open or closed. In the closed position you would see some ohms reading for the heater coil. |
|
07-15-2017, 09:33 AM | #19 |
Senior Member
Join Date: Mar 2014
Location: Webster, NY
Posts: 215
|
Re: Need 6V gas tank sending unit rebuilt
I'm sorry JSeery - do you ever get tired of having to repeat yourself? Obviously the PO replaced my sending unit. So the seller is wrong if a for sale supposed OEM/NOS sending unit shows a range of resistance (as above) between the connection and ground. How do you tell if a sending unit is OEM/NOS and works? I just looked at the Detroit Iron reprint of the shop manual and it says to connect a new sending unit and operate the float arm. If the gauge works then the old sending unit was bad. Tough to do online or at a swap meet.
|
07-15-2017, 10:14 AM | #20 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
I hear ya. I've never seen a Ford or King Seegley test procedure except pull and replace. The first thing I would try to check would be to see if you can get the contacts (points) to open and close by moving the float arm on a fuel gauge and checking with an ohms meter. Closed should read very low ohms and open is open, LOL. They are very well made gauges and can often be brought back to life by cleaning the contacts.
|
07-15-2017, 12:48 PM | #21 |
Senior Member
Join Date: Mar 2014
Location: Webster, NY
Posts: 215
|
Re: Need 6V gas tank sending unit rebuilt
The gauge is fine. I now want an OEM style sending unit; do not want to drop the tank to install the old, but better working resistor unit with a new float in place of the "new" worthless Mac's replacement that I installed three years ago. I'll take my ohmmeter to swap meets and avoid any resistance units. From 19Fordy's post in another thread I at least know that the Ford p/n should be on the tank side of the flange. Thanks for all the help. Now I know what I did not know.
|
07-15-2017, 09:35 PM | #22 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Need 6V gas tank sending unit rebuilt
Ok, I don't have a lot of K-S fuel senders to play with, but I did pull one out of a tank this evening and started playing around with it. For starters with no power connected to it the contacts are closed no matter where the float is positioned. The ohms through the contacts to ground is 2-3 ohms. I am going to try some different test procedures and see if anything looks promising.
|
Sponsored Links (Register now to hide all advertisements) |
|
07-15-2017, 10:17 PM | #23 |
Senior Member
Join Date: Mar 2014
Location: Webster, NY
Posts: 215
|
Re: Need 6V gas tank sending unit rebuilt
Thanks. Would be neat to come up with a small text fixture. Is that a good sending unit that you are playing with? If so, at least we now know that there should be a constant 2-3 ohms. That in itself is a good start.
|
07-16-2017, 08:54 AM | #24 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Need 6V gas tank sending unit rebuilt
When checking resistance of a King Seeley sender from the early Ford V8 era, a person it basically checking the heating element circuit inside there. It would be interesting to know what the average values are. Many of them have a wire spool in there that I assume was placed there so that resistance could be adjusted for calibration purposes during manufacture but the units should all be relatively close in the resistance values within a range at least. The bimetallic strips can be made exactly the same way but that doesn't mean that they will bend the same amount when the same heat is applied so this gave the manufacture a way to calibrate things for a consistent reading with all units. There was also another adjustment for positioning. Both adjustments were likely made at initial testing and would basically never change throughout the life of the instrument. If a person is very careful during points cleaning or other service inspections/checks. The unit should not need any adjustments.
|
09-18-2023, 09:52 AM | #25 |
Senior Member
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,800
|
Re: Need 6V gas tank sending unit rebuilt
No NON SEELEY sending unit will ever work correctly with the stock gauge. BECAUSE THE SENDER AND GAUGE WORK ON FREQUENCY OF THE POINTS THAT ARE IN THE SENDER. A NOS sender that has been sitting for 90 plus years probably had some corrosion on the points just like your distributor will have if not run for a long time with open points. The float arm changes the "adjustment" of the points and changes the frequency which the gauge is calibrated to read. I think somewhere in the Ford Service Manual there is directions on how you calibrate the gauge to your sender. Of course the sender must be good. Carefully pulling some fine wet dry paper through the points will usually fix the problem. I have done this many times with success.
The gauge does not properly work with varying ohms resistance values sent to it because it is calibrated to the varying FREQUENCY the sender sends. This keeps coming up because the people selling those sending units have NO IDEA how the gauge works. If you are using an aftermarket sending unit, buy and aftermarket gauge, install that like you would other aftermaket gauges and that will work like it should. |
09-18-2023, 10:25 AM | #26 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Need 6V gas tank sending unit rebuilt
Sponsored Links (Register now to hide all advertisements)
So true. That's the bottom line when using aftermarket sending units. |
09-18-2023, 01:10 PM | #27 |
Senior Member
Join Date: Dec 2012
Location: CT
Posts: 394
|
Re: Need 6V gas tank sending unit rebuilt
This thread has given me my potential winter project.
The issues as I see them Sealy gauges almost impossible to get New tanks won’t except the Sealy gauge (unbelievable!!!) I’m not sure these resistive based gauges can even be installed in a tank without current limiting. Resistive based tank sending units not compatable with stock fuel gauge I’m thinking a small interface box under the dash with a microprocessor doing the work necessary to feed the correct amount of current to the stock fuel gauge |
09-19-2023, 08:56 AM | #28 |
Senior Member
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,800
|
Re: Need 6V gas tank sending unit rebuilt
I have read that some of the newer tanks have mounting holes for original and new sending units. Maybe Drake.
|
09-19-2023, 09:02 AM | #29 |
Senior Member
Join Date: Jul 2010
Location: 36 miles north of Albany NY
Posts: 2,954
|
Re: Need 6V gas tank sending unit rebuilt
|
09-19-2023, 10:28 AM | #30 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Need 6V gas tank sending unit rebuilt
corvette8n: This looks like it could be used. You just have to make a bracket to hold the gauge. Call the company first to verify.
https://the-co.com/product/720730fg6vp/ |
09-19-2023, 11:04 AM | #31 | |
Senior Member
Join Date: May 2015
Posts: 8,166
|
Re: Need 6V gas tank sending unit rebuilt
Quote:
https://the-co.com/product/720730fg6vp/ JD FUEL GAUGE & SENDING UNIT – 6 VOLT POSITIVE GROUND Item #: 720730FG6VP Price: $59.95 $49.95 Item Details Weight 1.5 lbs OEM AB5139R, AF2173R, AR1112R Manufacturers John Deere John Deere 70D, 720D, 730D, 80, 820, 830
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
09-20-2023, 12:43 AM | #32 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,945
|
Re: Need 6V gas tank sending unit rebuilt
Or if you have converted to 12 v, a fuel gauge from a toyota landcruiser fj 40 will mount in your instrument cluster with little or no modification. It uses an ohm type sender the landcruiser places sell for 30 bucks. Or get one from toyota. Same depth gauge, same mounting to the ford 2 eared, 2 hole circular mount with the cross in the center. Get the stick on gauge face from a vintage ford place to make it look like your year ford.. I started playing with this last winter when I saw how similar the two instruments are. These are made by yazaki meter and I think available from toyota parts. No matter what you think about foreign cars the Japanese know their electrical systems. The gauge is a dead on bolt up to a '40-'47 panel and others that match that. I think I read the gauge has a resistor that turns 12 v to 7v. , but I'm no electrician, I just know what fits in that panel. My plan is to redrill the flange on the toyota sender, And there's nothing hanging under the dash. The toyota gauge is actually a tiny bit smaller on the face than the ford, the perspective shows the opposite.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
09-20-2023, 12:46 AM | #33 | |
Senior Member
Join Date: May 2015
Posts: 8,166
|
Re: Need 6V gas tank sending unit rebuilt
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|