|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-19-2020, 09:44 PM | #1 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,943
|
Removing Engine from '40 Ford Question
Using a standard size engine hoist with a boom, is it possible to remove an 8BA engine from a 40 Ford car WITHOUT
removing the HOOD, FRONT SHEET METAL or GRILLE? I've done it by removing only the hood and radiator but, am wondering if it's really necessary. Anyone done it that way? Thanks, JIM |
05-19-2020, 11:40 PM | #2 |
Senior Member
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,800
|
Re: Removing Engine from '40 Ford Question
Don't know about an 8ba but I have removed the 40 engine from my wagon after only removing the radiator and leaving the hood on. l left the trans in the car with a jack under it and used 4 line up pins (long bolts with heads cut off and screwdriver slots cut in the ends) when installing the motor. This was to fix a junk new TO bearing that lasted 7 miles. Was pretty easy as I unbolted the exhaust manifolds from the block and left the exhaust system intact.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-19-2020, 11:47 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,574
|
Re: Removing Engine from '40 Ford Question
a tape measure would tell you. 1st you would need to mount as close as possible to the motor to reduce the height needed, then once free of the tranny you can start going up so you will gain clearance as you go forward. never done it on a 40, just "thinking out loud". i'll bet kube has some thoughts about this
|
05-20-2020, 05:11 AM | #4 |
Senior Member
Join Date: May 2010
Posts: 1,770
|
Re: Removing Engine from '40 Ford Question
why take a chance of damage if you just take the pivot bolts off the hood you do not change the hood fit
|
05-20-2020, 06:28 AM | #5 |
Senior Member
Join Date: Sep 2013
Location: Dighton, Mass
Posts: 1,230
|
Re: Removing Engine from '40 Ford Question
Is it necessary? Removing the radiator and hood makes life way easy. Like the Duece
said unbolt manifolds and leave it -better than fooling with nasty exhaust always frozen pipe bolts. The hood not heavy just two people each with a wrench = hood over your shoulders no damage done. Whatever do not remove engine and transmission with the common cherry picker cause it will take a nose dive unless you have the high end picker that the front wheels slide way out or you need somebody to stand on the picker back, that turns this into three people one to stand on it and two to pull it out LOL Thats a chain fall job. sam |
05-20-2020, 07:56 AM | #6 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,007
|
Re: Removing Engine from '40 Ford Question
Sponsored Links (Register now to hide all advertisements)
Quote:
LOTS of heavy blankets...
__________________
"I can explain it for you. However, I can't understand it for you". |
|
05-20-2020, 08:01 AM | #7 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,752
|
Re: Removing Engine from '40 Ford Question
I've taken a 59A style motor from my 40 coupe without removing anything except the radiator. Mine was a deluxe model. I did take out the trans cover. If you undo the hood supports the hood will open higher than normal and in my case I tied it back to the rear bumper with a rope.
You have to attach the hoist to the motor very low down. Mart. I found a pic: Last edited by Mart; 05-20-2020 at 08:14 AM. |
05-20-2020, 08:37 AM | #8 |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 832
|
Re: Removing Engine from '40 Ford Question
Seems like more risk to damage something than it's worth even if it can be done.
|
05-20-2020, 08:55 AM | #9 |
Senior Member
Join Date: Aug 2010
Location: newark, delaware
Posts: 3,735
|
Re: Removing Engine from '40 Ford Question
I just changed a 8ba in a 40 pickup. Took out the radiator and the hood off
I did as mentioned above and took the manifold off the motor and left them in the chassis with the exhaust. I also took the oil filter , carburetor , fuel pump with stand and distributor off . The less stuff to get hung up on something and had to swap all that stuff to the new motor anyway. I also have a I beam with a chain hoist and trolley which is way easier then a cherry picker. Junk cars i pull motors with a forklift.... A word of advice, sweep the floor before you try to roll the cherry picker....the tiniest piece of anything will stop you in your tracks and can be deadly |
05-20-2020, 09:19 AM | #10 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: Removing Engine from '40 Ford Question
I removed the engine from my 39 DeLuxe like Mart did.
|
05-20-2020, 09:52 AM | #11 | |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 3,260
|
Re: Removing Engine from '40 Ford Question
Quote:
Last edited by Ken/Alabama; 05-20-2020 at 10:01 AM. |
|
05-20-2020, 10:10 AM | #12 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,943
|
Re: Removing Engine from '40 Ford Question
Thank you all very much for sharing your experience and knowledge.
Thanks, Mart, for posting that photo. My decision is pending as there's a strange "tinny" sound coming from the engine that comes and goes at idle. Great oil pressure and runs smooth. Can't figure out what it is. Last time I removed the engine was in 1972 with a chain fall. I removed the hood myself, back then when I was 29 and back was fine. See photo of engine back then. Last edited by 19Fordy; 05-20-2020 at 10:17 AM. |
05-20-2020, 10:37 AM | #13 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,113
|
Re: Removing Engine from '40 Ford Question
Sooo, let's seeeeee…...that should make you about 43-ish NOW? Damn you're gettin' old! DD |
05-20-2020, 11:04 AM | #14 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Removing Engine from '40 Ford Question
Yes. I have done it several times. Did nothing but remove the radiator. Left the transmission in, unbolted the exhaust from the block only. If you look at Mart's photo, he did not need to unbolte the hood.
|
05-20-2020, 11:13 AM | #15 |
Senior Member
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,800
|
Re: Removing Engine from '40 Ford Question
I too have that KRW tool Ken has that fits in the valley and it is quite handy, quick to put in and take out, those 2 pins keep it from moving.
|
05-20-2020, 01:37 PM | #16 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: Removing Engine from '40 Ford Question
My preference on my '39 is to remove grill and radiator only and take everything out the front...and keep everything as low as possible, relative to shop crane.....swaying engine over fenders makes me really nervous!! Putting '39 grill back in is an easy one person job. Putting hood back on is a two person for me!!
|
05-20-2020, 03:04 PM | #17 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: Removing Engine from '40 Ford Question
Over the past 20 years we;ve remover and installed a Ardun/C4 combination a dozen times. Have to install it this year again, come and watch. But we do take the hood off.
|
05-20-2020, 04:11 PM | #18 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,113
|
Re: Removing Engine from '40 Ford Question
Quote:
I've gotta ask.....WHO would waste a beautiful ARDUN on a slushbox transmission? Isn't that considered to be some sort of crime against nature? DD |
|
05-21-2020, 06:31 PM | #19 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: Removing Engine from '40 Ford Question
Yes, I might agree, I suggested an AOD. It's beautiful car and MIGHT be up for sale soon????
|
05-21-2020, 07:01 PM | #20 | |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,037
|
Re: Removing Engine from '40 Ford Question
Quote:
Same way I do it. a lot less chance of something smacking a fender. |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|