Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 06-14-2020, 03:06 PM   #1
txmike
Senior Member
 
Join Date: Jun 2010
Location: DFW Area
Posts: 165
Default Negative Battery Cable

I have a 1929 Ford Coupe. Went out this morning top test my restored pop out ignition. Started fine.... let it idle for about 5 mins then took her out of the driveway and it died. Would not start back up.....

Let it sit for awhile and went and put the battery charger on it.
When i removed the access panel to the battery the negative cable has separated from where it clamps on to the battery. Look like it melted?

Fuse did not blow....

What gives... I now know what it will not start

thanks
txmike is offline   Reply With Quote
Old 06-14-2020, 03:21 PM   #2
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: Negative Battery Cable

Well it either was not the right gauge and melted with the electricity or something shorted there which is odd because it is right at the beginning of the electrical system.

It should be number 1 gauge like this:
https://www.brattons.com/original-ba...tch-cable.html
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-14-2020, 03:51 PM   #3
txmike
Senior Member
 
Join Date: Jun 2010
Location: DFW Area
Posts: 165
Default Re: Negative Battery Cable

It was the right cable.... any idea why it would short and melt there?
txmike is offline   Reply With Quote
Old 06-14-2020, 03:56 PM   #4
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Negative Battery Cable

Is your car still positive ground? Maybe your negative cable was rubbing against something and caused a direct short. It would get hot in a hurry.
Y-Blockhead is offline   Reply With Quote
Old 06-14-2020, 04:25 PM   #5
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: Negative Battery Cable

Any chance it shorted to the battery hold down?

Charlie Stephens
Charlie Stephens is offline   Reply With Quote
Old 06-14-2020, 04:29 PM   #6
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: Negative Battery Cable

Sponsored Links (Register now to hide all advertisements)
Yes the terminal on the wire can rub up against the hold down if you are not careful when installing it or using the wrong parts. It can also move and short out if not tight enough.
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Old 06-14-2020, 05:33 PM   #7
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: Negative Battery Cable

High resistance due to a loose connection can cause a load just like an electric heater coil. There would only be current flow if there is a pathway for it to go. I'd certainly check the power cable to the starter for a short. It would take a lot of current load to generate that much heat.

It had to have died on you for a reason. The open circuit is likely. I assume it wouldn't turn over or there would have been no reason to hook up the battery charger. I wonder what the amp meter was reading while it was idling for the 5 minutes? If the starter cranked after it died, how long did you crank the starter to try for restart or was the starter non-functional after it died?
rotorwrench is offline   Reply With Quote
Old 06-14-2020, 06:13 PM   #8
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Negative Battery Cable

I agree with either a loose connection or the terminal contacting the metal hold down bracket. I slid a piece of thin plastic tube over the cable and tape it in place.

The tube is just big enough to slide over the cable terminal [ keeps it off [away] the bracket and extend forward past the brake pedal. That would be , what, about 8" or so.

Last edited by Patrick L.; 06-15-2020 at 05:32 PM.
Patrick L. is offline   Reply With Quote
Old 06-14-2020, 06:52 PM   #9
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Negative Battery Cable

Got a picture?
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 06-14-2020, 07:02 PM   #10
txmike
Senior Member
 
Join Date: Jun 2010
Location: DFW Area
Posts: 165
Default Re: Negative Battery Cable

looks like a loose battery connection
I will buy a new one and see what i find out - thanks to all
txmike is offline   Reply With Quote
Old 06-14-2020, 08:15 PM   #11
30 Closed Cab PU
Senior Member
 
Join Date: Aug 2018
Posts: 2,332
Default Re: Negative Battery Cable

I seem to remember there was a cable routing change in the service bulletins for rerouting the cable from the battery to the Starter due to wearing of the cable insulation on something. Sorry do not remember all the details.
30 Closed Cab PU is offline   Reply With Quote
Old 06-15-2020, 03:28 AM   #12
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: Negative Battery Cable

They changed the routing because it was discovered that the pedals would wear on the cable eventually getting to the wire and shorting it out.
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:28 AM.