|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-28-2022, 01:46 PM | #1 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
1935 Wire Wheel Backspacing and offset
Can some please tell me what those dimension are?
Thank you, Joe |
08-28-2022, 08:18 PM | #2 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: 1935 Wire Wheel Backspacing and offset
I can't give you those dimensions right off the top of my head, but I CAN tell you that they will vary a few thousandths between each wheel. One size does not necessarily fit all, here.
WHOOPS: I read that to mean support spacers between the wheel and hub when using later drums with wire spoke wheels. My bad.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
Sponsored Links (Register now to hide all advertisements) |
|
08-28-2022, 10:46 PM | #3 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,053
|
Re: 1935 Wire Wheel Backspacing and offset
You talking model A to 35? or wire to 40s?
|
08-29-2022, 03:24 AM | #4 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,114
|
Re: 1935 Wire Wheel Backspacing and offset
Not sure why folks want to confuse with answers to questions that they don't understand. This is a "one-year-only", 1935 Ford 16" wire wheel. "Re: 1935 Wire Wheel Backspacing and offset" Simple questions: What is BACKSPACING? What is OFFSET? Sorry Joe, that I don't have those figures, nor a wheel to measure such! Coop . |
08-29-2022, 02:22 PM | #5 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
Re: 1935 Wire Wheel Backspacing and offset
Quote:
|
|
08-29-2022, 02:30 PM | #6 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,320
|
Re: 1935 Wire Wheel Backspacing and offset
Sponsored Links (Register now to hide all advertisements)
|
08-29-2022, 02:57 PM | #7 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: 1935 Wire Wheel Backspacing and offset
I have a couple sets of what I think is in Coops picture.I’ll check in later to see if you got measurements……Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
08-29-2022, 06:03 PM | #8 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: 1935 Wire Wheel Backspacing and offset
I come up with 3 1/8 backspace and 9/16 positive offset. Again, as long as these are the same wheels you’re talking about........Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver Last edited by flatford8; 08-29-2022 at 07:14 PM. |
08-29-2022, 08:22 PM | #9 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: 1935 Wire Wheel Backspacing and offset
I took some 3/16 rod !made a ring the size that fit the rim ,welded it togeather to form ring
then laid in in wheel,put a straight across the holes from one to the other then ground the ring to be flush with lug holes,,made a little clip to hold them in place when you put wheel on,,,I believe it helped some with the wiggle,I only needed them on front.
__________________
DON P |
08-30-2022, 02:16 AM | #10 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
Re: 1935 Wire Wheel Backspacing and offset
|
08-30-2022, 02:17 AM | #11 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
Re: 1935 Wire Wheel Backspacing and offset
|
08-30-2022, 02:18 AM | #12 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
Re: 1935 Wire Wheel Backspacing and offset
|
08-30-2022, 02:23 AM | #13 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,114
|
Re: 1935 Wire Wheel Backspacing and offset
SAME spoke count (32). Hubs APPEAR to be same. OUGHT to work! Coop |
08-30-2022, 02:45 AM | #14 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,427
|
Re: 1935 Wire Wheel Backspacing and offset
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|