|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-10-2016, 03:33 PM | #1 |
Senior Member
Join Date: Jul 2013
Location: Johnstown, PA.
Posts: 137
|
Head gasket again
I wanted to buy a "BEST" brand head gasket but it seems that none of the big Model A part houses sell the "BEST" brand. "BEST doesn't sell retail so if it's so good, why isn't it avaible through the normal channels?
|
07-10-2016, 03:36 PM | #2 |
BANNED
Join Date: May 2010
Location: Michigan / Ontario border, Sarnia, Ontario. 50 miles from Detroit and 150 from Toronto.
Posts: 5,800
|
Re: Head gasket again
Ask the manufacturer who retails their product! Wayne
|
Sponsored Links (Register now to hide all advertisements) |
|
07-10-2016, 03:37 PM | #3 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Head gasket again
Go to Bests web site,they list the suppliers there.
Lawrie |
07-10-2016, 04:21 PM | #4 |
Senior Member
Join Date: Jul 2010
Location: Auckland, New Zealand
Posts: 514
|
Re: Head gasket again
HI Divco1,
I have just bought BEST G509 from Arizona Model A and G573 from Steve Becker at Berts. 509 is for A head up to 4 inch bore and 573 is similar but with 2 small steam hole for B engines. It also fits A's and both work well with Snyders higher compression heads. Just ask for them by BEST part number as I don't think they are listed as BEST in the catalogues but I think Steves one is A 6051 B composition gasket.. These numbers are from memory as I don't have the gaskets or receipts with me at present. SAJ back in NZ |
07-10-2016, 04:25 PM | #5 |
Senior Member
Join Date: Sep 2012
Location: New Jersey shore
Posts: 257
|
Re: Head gasket again
The last "Best" head gasket I purchased was a B style from Snyders
|
07-10-2016, 04:44 PM | #6 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Head gasket again
Sponsored Links (Register now to hide all advertisements)
http://secretsofspeed.com/gaskets.htm |
07-14-2016, 11:39 AM | #7 |
Senior Member
Join Date: Apr 2014
Location: Connecticut
Posts: 130
|
Re: Head gasket again
For Thomas Head from Snyders part number is B-6051-C it has 573 stamped on it, I had tried copper first, spoke to them and they recommended this one as it was thinner and would not require many re-torques. Note I had leak up head bolt between 1 and 2 when I pulled head there was nothing wrong with copper gasket. 250 miles on new rebuild. Diamond block.
|
07-14-2016, 08:58 PM | #8 |
Senior Member
Join Date: May 2010
Location: Northport, NY
Posts: 1,597
|
Re: Head gasket again
Antique Engines in Skokie recommends Best 573 for their hi compression head engines which is available at ANTIQUE FORD on Long Island. 631 256 0030.
Last edited by Bruce Adams; 07-15-2016 at 04:29 AM. |
07-15-2016, 07:54 PM | #9 |
Senior Member
Join Date: May 2010
Location: Camino, CA.
Posts: 3,086
|
Re: Head gasket again
I buy my head gaskets from Brattons, spray them with Copper Coat, put a 2" piece of copper wire in the Copper Coat between #3 AND #4 for renforcement, and reinstall the head. Torque to 50#, run to operating temp and torque to 55#
|
07-15-2016, 08:26 PM | #10 |
Senior Member
Join Date: Jul 2013
Location: Johnstown, PA.
Posts: 137
|
Re: Head gasket again
I ordered the "best" gasket from Sandy Olson. My original question was why don't the big 3 or 4 model A suppliers sell the gasket that a lot of people recommend. Snyders sell the 573 but not the 509. Best doesn't recommend the 573 with a stock head.
|
07-15-2016, 10:40 PM | #11 | |
Senior Member
|
Re: Head gasket again
Quote:
Best bet is to ask them to get the true answer.
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II |
|
07-15-2016, 11:26 PM | #12 |
BANNED
Join Date: May 2012
Location: inside your RAM
Posts: 3,134
|
Re: Head gasket again
they prolly have a mountain of FelPros on the shelf they need to move. The FelPros only fit the stock head well; they fit the HC heads very poorly
__________________
'31 180A |
07-15-2016, 11:50 PM | #13 |
Senior Member
Join Date: May 2010
Location: Lakewood, CA
Posts: 1,346
|
Re: Head gasket again
What gasket would you guys recommend for a Model B police head on a Model A block?
Neil |
07-16-2016, 12:47 AM | #14 |
Senior Member
|
Re: Head gasket again
I trust the head manufacturer. The Brumfeld HC head calls out a R3 Felpro.
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II |
07-16-2016, 09:48 AM | #15 |
BANNED
Join Date: May 2012
Location: inside your RAM
Posts: 3,134
|
Re: Head gasket again
only the R4 avail now as far as i know
never had a Brumfield in my hand to examine the fit in the valve area. That is where some gaskets do not match up well
__________________
'31 180A |
|
|
Sponsored Links (Register now to hide all advertisements) |
|