|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-28-2016, 02:58 AM | #1 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
cam shaft centre line
Any one know the centre distance between the camshaft and the crankshaft centres.
also the bore diameter of the block were the valve guides fit. Thanks Lawrie |
05-28-2016, 03:31 AM | #2 |
Member
Join Date: Jul 2010
Location: Canterbury, New Zealand
Posts: 95
|
Re: cam shaft centre line
Lawrie Have a look on Vince Falters site , ford garage.com. I know he has the center line measurements you need . Good luck
|
Sponsored Links (Register now to hide all advertisements) |
|
05-28-2016, 05:02 AM | #3 |
Senior Member
Join Date: Mar 2013
Location: Australa Melbourne
Posts: 878
|
Re: cam shaft centre line
Lawrie I set up for 4.155"
|
05-28-2016, 05:29 AM | #4 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Thanks Guys that is exactly what I needed.
Lawrie |
05-28-2016, 07:02 PM | #5 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Thanks ,Measured the centres this morning,.008 under,
Lawrie |
05-29-2016, 11:58 AM | #6 |
Junior Member
Join Date: Mar 2012
Location: Mahtomedi, MN
Posts: 7
|
Re: cam shaft centre line
Sponsored Links (Register now to hide all advertisements)
|
05-29-2016, 03:01 PM | #7 |
Senior Member
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,496
|
Re: cam shaft centre line
Dan did the same for me they mesh perfectly. Thanks Dan...
|
05-30-2016, 10:19 AM | #8 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
Re: cam shaft centre line
Four and a half years after this thread, I had to call on Dan to provide me with a -.005" timing gear to salvage a "fresh" short block that has been haunting me for decades after a run-in with America's Sweetheart antique engine family. The mains had been line bored just a little off. Hoping that it's not your problem just keep the Dan option in mind if it continues to destroy timing gears. Good Luck: Fred A
|
05-30-2016, 03:50 PM | #9 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Sure will, I have just yesterday fixed the main bolts looseness up,and will then look at the fix for the cam.
Lawrie |
05-30-2016, 04:36 PM | #10 |
Senior Member
Join Date: Mar 2013
Location: Australa Melbourne
Posts: 878
|
Re: cam shaft centre line
Lawrie I am sure you know but check center line front and back
|
05-30-2016, 04:41 PM | #11 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Sure will
Lawrie |
06-11-2016, 12:58 AM | #12 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Would any one have an e/mail for Dan Mc eachern.
to save me ringing at an ungodly hour for me. Thanks Lawrie |
06-11-2016, 03:47 AM | #13 |
Senior Member
Join Date: Mar 2013
Location: Australa Melbourne
Posts: 878
|
Re: cam shaft centre line
Lawrie try
[email protected] |
06-11-2016, 04:53 PM | #14 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: cam shaft centre line
Thanks Colin,
I,m onto it. Lawrie |
|
|
Sponsored Links (Register now to hide all advertisements) |
|