|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-25-2017, 06:36 PM | #1 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
36 ford wiper motor
I have a 36 Ford convertible with the hart shaped wiper motor does anyone have a photo or diagram on all the parts to install in the windshield frame
__________________
Ford |
09-25-2017, 07:19 PM | #2 |
Senior Member
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
|
Re: 36 ford wiper motor
conv sedan/cabriolet or roadster/phaeton??????
|
Sponsored Links (Register now to hide all advertisements) |
|
09-25-2017, 08:44 PM | #3 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
Re: 36 ford wiper motor
Conv sedan
__________________
Ford |
09-26-2017, 08:41 AM | #4 |
Senior Member
Join Date: May 2010
Posts: 642
|
Re: 36 ford wiper motor
I have one I was going to take to Hershey BUT health issues have forced me to change plans. My space at Light 84 will be MT.
|
09-27-2017, 04:09 PM | #5 |
Senior Member
Join Date: May 2010
Location: Waddell, AZ
Posts: 2,540
|
Re: 36 ford wiper motor
Jacob, has Al Casteen been in touch with you about your C/S??
|
09-27-2017, 05:20 PM | #6 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
Re: 36 ford wiper motor
Sponsored Links (Register now to hide all advertisements)
__________________
Ford |
09-27-2017, 05:40 PM | #7 |
Senior Member
Join Date: May 2010
Posts: 4,725
|
Re: 36 ford wiper motor
From the hardware book it appears the same hardware as the Cabriolet. Special nut for the shaft, flat washer, Grommet 48-761370 (flat rubber or leather same OD as washer and same ID as the shaft) On the interior is the spacer 48-761424. I believe that is all.
|
09-28-2017, 08:04 PM | #8 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
Re: 36 ford wiper motor
Terry would you know were to get one? And how is it installed
__________________
Ford |
09-29-2017, 06:16 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 4,725
|
Re: 36 ford wiper motor
Ford used the spacer with different lengths and finish on a number of cars. If you can find a longer one you can whittle it down to the correct length and have it chromed. It is made of white metal. The wiper shaft slides through the hole in the center and the step goes against the motor and holds it in place without any attachment hardware. The two small tits on the other end go against the wind shield frame. The one stem nut (5/16-32 with 7/16 hex) holds the assembly together. I believe Kent Jaquith at "Clean Sweep" has the spacer
Kent Jaquith Clean-Sweep 2633 SW Obsidian # 15 Redmond, Oregon (541) 923-4319 Last edited by Terry,OH; 09-29-2017 at 06:47 AM. |
09-30-2017, 08:39 PM | #10 |
Senior Member
Join Date: Nov 2014
Location: New ringgold pa
Posts: 311
|
Re: 36 ford wiper motor
Thank you Terry. I checked with Kent and he is out right know. I am going to Hershey next week maybe I will get lucky
__________________
Ford |
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|