Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-09-2012, 08:16 PM   #1
Wilbur
Senior Member
 
Wilbur's Avatar
 
Join Date: Nov 2012
Location: Mays Landing, NJ
Posts: 113
Default Opinions on using a Shortened Pitman Arm

What do you guys have to say regarding using the imported shortened pitman arm to reduce steering effort?
Wilbur is offline   Reply With Quote
Old 12-09-2012, 08:48 PM   #2
Gord. B by the bay
Senior Member
 
Join Date: May 2010
Location: Owen Sound Ont. Canada
Posts: 198
Default Re: Opinions on using a Shortened Pitman Arm

Money well spent i have one on each A Grod B by the Bay
Gord. B by the bay is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-09-2012, 09:10 PM   #3
allen
Senior Member
 
allen's Avatar
 
Join Date: May 2010
Location: petal mississippi
Posts: 550
Send a message via ICQ to allen
Default Re: Opinions on using a Shortened Pitman Arm

Snyders now sells them, so no cutting and welding all four of my A's have them
allen is offline   Reply With Quote
Old 12-09-2012, 09:23 PM   #4
2manycars
Senior Member
 
2manycars's Avatar
 
Join Date: May 2010
Location: Eastern CT
Posts: 2,732
Default Re: Opinions on using a Shortened Pitman Arm

I cut and welded mine 10 years ago, and I find it to ease steering effort, with no loss of turning radius. I just bought a new one for the coupe. I could have welded another, but a new one was easier.
2manycars is offline   Reply With Quote
Old 12-09-2012, 09:36 PM   #5
allen
Senior Member
 
allen's Avatar
 
Join Date: May 2010
Location: petal mississippi
Posts: 550
Send a message via ICQ to allen
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by 2manycars View Post
I cut and welded mine 10 years ago, and I find it to ease steering effort, with no loss of turning radius. I just bought a new one for the coupe. I could have welded another, but a new one was easier.

Totally agree, 35 dollars very worth it.
allen is offline   Reply With Quote
Old 12-09-2012, 10:02 PM   #6
Wilbur
Senior Member
 
Wilbur's Avatar
 
Join Date: Nov 2012
Location: Mays Landing, NJ
Posts: 113
Default Re: Opinions on using a Shortened Pitman Arm

Sponsored Links (Register now to hide all advertisements)
Sounds good. My wife has a hard time with the steering on her 29. Thanks
Wilbur is offline   Reply With Quote
Old 12-09-2012, 10:52 PM   #7
pat in Santa Cruz
Senior Member
 
pat in Santa Cruz's Avatar
 
Join Date: May 2010
Location: santa cruz, calif
Posts: 2,011
Default Re: Opinions on using a Shortened Pitman Arm

the new manufactured ones are the safest. There have been failures with welded ones. Even Henry shortened the pitman arm for 1932. Combine it with round spindle balls and the steering gets much easier. If the spindle balls are .020 out of round, they will contribute to stiff steering. A&L re balls the spindle arms the right way so the ball does not break off. With new smooth surfaces you can use the Teflon buttons, AKA EZ steer kit, in the tie rod and drag link ends which will make it even easier to steer..
pat in Santa Cruz is offline   Reply With Quote
Old 12-10-2012, 02:29 PM   #8
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Opinions on using a Shortened Pitman Arm

I agree, a short pitman arm is the way to go for easy steering.
However, I have gone the other way with a longer one on my F100 box along with a linear controlled power assist cylinder.
It gives me 3/4 turn lock to lock which is ideal for the type of driving I have come to enjoy most of late. Going FAST down dirt logging roads. I can see why rally racers do what they do.
Pete is offline   Reply With Quote
Old 12-10-2012, 03:11 PM   #9
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Opinions on using a Shortened Pitman Arm

I tried one on my 40B. Being a light car, I did not feel any significant ease in the steering effort. It did, however make it feel like I was driving a bus with the slowed ratio. I put the stock arm back on. I like the quicker steering and more direct road feel.
MikeK is offline   Reply With Quote
Old 12-10-2012, 03:41 PM   #10
#1modelafan
Junior Member
 
Join Date: Nov 2012
Posts: 6
Default Re: Opinions on using a Shortened Pitman Arm

I have a shorted pitman arm on one of Model A's. I do not find it to make any difference in the required turning effort. Also, now it takes a lot more area to make a U turn. When I get time, I plan to replace back to an original. Lee
#1modelafan is offline   Reply With Quote
Old 12-10-2012, 04:22 PM   #11
Barry B./ Ma.
Senior Member
 
Barry B./ Ma.'s Avatar
 
Join Date: May 2010
Location: Southbridge, Ma.
Posts: 1,614
Default Re: Opinions on using a Shortened Pitman Arm

I have a new one on my roadster and it makes it easier to turn. The wheels still turn lock to lock so the radius didn't change.
Barry B./ Ma. is offline   Reply With Quote
Old 12-10-2012, 04:39 PM   #12
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by Ross/Kzoo View Post
An added advantage is that it keeps the drag link separated from the tie rod, no rubbing.
????
Pete is offline   Reply With Quote
Old 12-10-2012, 04:47 PM   #13
CarlG
Senior Member
 
CarlG's Avatar
 
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,109
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by Ross/Kzoo View Post
An added advantage is that it keeps the drag link separated from the tie rod, no rubbing.
Quote:
Originally Posted by Pete View Post
????
Probably caused by a sagging front spring ??
CarlG is offline   Reply With Quote
Old 12-10-2012, 04:51 PM   #14
Terry, NJ
Senior Member
 
Terry, NJ's Avatar
 
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
Default Re: Opinions on using a Shortened Pitman Arm

Anyone have any instructions on welding one of these up? Where to make the cut? What rod works best (70/ 8018LH?) Preheat? Cool slowly or quench? I am thinking of drilling it out and putting a 5/16 X 2" rod down the middle, in effect, a spine. Or weld a piece on the back where it can't be seen to bridge over the weld. Jest thinkin'!
Terry
Terry, NJ is offline   Reply With Quote
Old 12-10-2012, 04:51 PM   #15
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by Ross/Kzoo
An added advantage is that it keeps the drag link separated from the tie rod, no rubbing.

Quote:
Originally Posted by Pete
????

Probably caused by a sagging front spring ??




The drag link is on top of the spindle.
The tie rod is on the bottom of the spindle.
Pete is offline   Reply With Quote
Old 12-10-2012, 04:52 PM   #16
Ross/Kzoo
Senior Member
 
Ross/Kzoo's Avatar
 
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by CarlG View Post
Probably caused by a sagging front spring ??
Yes!
Ross/Kzoo is offline   Reply With Quote
Old 12-10-2012, 05:01 PM   #17
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by Ross/Kzoo View Post
Yes!
It is physically impossible for the drag link and the tie rod to rub on a stock A front end. Not even if you remove the spring...Not even if you disconnect the drag link from the pitman are and lay the end on the ground. They are seperated by 7 inches.
Pete is offline   Reply With Quote
Old 12-10-2012, 05:13 PM   #18
Ross/Kzoo
Senior Member
 
Ross/Kzoo's Avatar
 
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
Default Re: Opinions on using a Shortened Pitman Arm

Maybe I called it wrong but there was rubbing. I about started from scratch so maybe I did something wrong. I'll post pictures later.
Attached Images
File Type: jpg IMG_0198.jpg (68.5 KB, 86 views)
File Type: jpg IMG_0199.jpg (54.9 KB, 84 views)

Last edited by Ross/Kzoo; 12-10-2012 at 05:27 PM.
Ross/Kzoo is offline   Reply With Quote
Old 12-10-2012, 05:25 PM   #19
allen
Senior Member
 
allen's Avatar
 
Join Date: May 2010
Location: petal mississippi
Posts: 550
Send a message via ICQ to allen
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by Terry, NJ View Post
Anyone have any instructions on welding one of these up? Where to make the cut? What rod works best (70/ 8018LH?) Preheat? Cool slowly or quench? I am thinkingg of drilling it out and putting a 5/16 X 2" rod down the middle, in effect, a spine. Or weld a piece on the back where it can't be seen to bridge over the weld. Jest thinkin'!
Terry

Terry the way i did mine is cut a v take out 1and 1/2 preheat oven 450 the used cast iron rods build with each pass when done pack it in sand and let cool. done this with three none broke couple of thousand miles on each
allen is offline   Reply With Quote
Old 12-10-2012, 05:31 PM   #20
MikeK
Senior Member
 
MikeK's Avatar
 
Join Date: May 2010
Location: Windy City
Posts: 2,919
Default Re: Opinions on using a Shortened Pitman Arm

Quote:
Originally Posted by allen View Post
Terry the way i did mine is cut a v take out 1and 1/2 preheat oven 450 the used cast iron rods build with each pass when done pack it in sand and let cool. done this with three none broke couple of thousand miles on each
Cast iron filler rod on a steel forging? Accident waiting to happen.
MikeK is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:42 AM.